REMOVE REAR NO. 1 SEAT ASSEMBLY RH (for 60/40 Split Seat Type 40 Side)
REMOVE REAR NO. 1 SEAT ASSEMBLY LH (for 60/40 Split Seat Type 60 Side)
REMOVE REAR SEAT COVER CAP (w/ Rear No. 2 Seat, except Face to Face Seat Type)
REMOVE REAR AIR DUCT GUIDE (w/ Rear Air Conditioning System)
REMOVE REAR NO. 7 AIR DUCT (w/ Rear Air Conditioning System)
Fuel Sender Gauge Assembly (For Fuel Sub Tank) -- Removal |
| 1. PRECAUTION |
- NOTICE:
- After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
| 2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
- NOTICE:
- When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).
Disconnect the cables from the negative (-) main battery and sub-battery terminals.
| 3. REMOVE REAR NO. 1 SEAT ASSEMBLY RH (for 60/40 Split Seat Type 40 Side) |
| 4. REMOVE REAR NO. 1 SEAT ASSEMBLY LH (for 60/40 Split Seat Type 60 Side) |
| 5. REMOVE REAR NO. 2 SEAT ASSEMBLY |
- for Face to Face Seat Type:
(Click here) - except Face to Face Seat Type:
(Click here)
| 6. REMOVE REAR STEP COVER |
- HINT:
- Use the same procedure for both rear step covers.
Detach the 2 claws and remove the rear step cover.
 |
| 7. REMOVE REAR DOOR SCUFF PLATE LH |
 |
Remove the screw.
Detach the 3 claws and 4 clips, and remove the rear door scuff plate LH.
| 8. REMOVE REAR DOOR SCUFF PLATE RH |
- HINT:
- Use the same procedures described for the LH side.
| 9. REMOVE REAR FLOOR MAT REAR SUPPORT PLATE |
 |
Detach the 6 clips and remove the rear floor mat support plate.
| 10. REMOVE REAR SEAT COVER CAP (w/ Rear No. 2 Seat, except Face to Face Seat Type) |
- HINT:
- Use the same procedure for both No. 1 luggage compartment trim hooks.
Using a screwdriver, detach the 3 claws and remove the rear seat cover cap.
- HINT:
- Tape the screwdriver tip before use.
Text in Illustration *a Protective Tape
 |
| 11. REMOVE FRONT QUARTER TRIM PANEL ASSEMBLY LH |
- w/ Sliding Roof:
(Click here) - w/o Sliding Roof:
(Click here)
| 12. REMOVE FRONT QUARTER TRIM PANEL ASSEMBLY RH |
- w/ Sliding Roof:
(Click here) - w/o Sliding Roof:
(Click here)
| 13. REMOVE AIR DUCT PLUG (w/ Rear Air Conditioning System) |
Detach the 2 claws and remove the plug.
- HINT:
- Use the same procedures for both sides.
 |
| 14. REMOVE REAR AIR DUCT GUIDE (w/ Rear Air Conditioning System) |
Remove the screw.
 |
Detach the claw and remove the guide.
- HINT:
- Use the same procedures for both sides.
| 15. SEPARATE REAR FLOOR MAT ASSEMBLY |
 |
w/ Rear Air Conditioning System:
Detach the 5 clips and fold back the rear floor mat assembly toward the front of the vehicle.- HINT:
- Fold back the rear floor mat assembly so that the rear No. 7 air duct can be removed.
w/o Rear Air Conditioning System:
Detach the 5 clips and fold back the rear floor mat assembly toward the front of the vehicle.- HINT:
- Fold back the rear floor mat assembly so that the service hole cover can be removed.
| 16. REMOVE REAR NO. 7 AIR DUCT (w/ Rear Air Conditioning System) |
Detach the 4 clips and remove the rear No. 7 air duct.
 |
| 17. REMOVE REAR FLOOR SERVICE HOLE COVER |
 |
| 18. REMOVE FUEL SENDER GAUGE ASSEMBLY |
Disconnect the fuel sender gauge connector.
 |
Remove the 5 screws and fuel sender gauge assembly.
- NOTICE:
- Be careful not to bend the arm of the fuel sender gauge assembly.
 |
Remove the gasket from the fuel sender gauge assembly.