Power Window Regulator Motor (For Rear Door) Installation

Apply MP grease to the sliding and rotating areas of the regulator motor assembly LH.

Using a T25 "TORX" socket wrench, install the power window regulator motor with the 3 screws.

Torque:

5.4 N*m{55 kgf*cm, 48 in.*lbf}

Apply MP grease to the sliding and rotating areas of the rear door window regulator.

NOTICE:

Do not apply grease to the spring of the window regulator.

w/ Power Window:

1. Temporarily install the temporary bolt to the rear door window regulator.
   

2. Install the rear door window regulator with the 3 bolts, and then tighten the temporary bolt.
   

   Torque:

   8.0 N*m{82 kgf*cm, 71 in.*lbf}

   Text in Illustration

   *1	Temporary Bolt

   NOTICE:

   Be careful not to drop the rear door window regulator as it may become damaged.

3. Connect the connector.
   

w/o Power Window:

1. Temporarily install the temporary bolt to the rear door window regulator.
   

2. Install the rear door window regulator with the 2 bolts, and then tighten the temporary bolt.
   

   Torque:

   8.0 N*m{82 kgf*cm, 71 in.*lbf}

   Text in Illustration

   *1	Temporary Bolt

   NOTICE:

   Be careful not to drop the rear door window regulator as it may become damaged.

w/ Power Window:

1. Temporarily install the rear power window regulator switch assembly with rear door armrest base panel.
   

2. Connect the cable to the negative (-) battery terminal.
   

3. Operate the rear door window regulator so that the rear door glass can be installed.
   

4. Disconnect the cable from the negative (-) battery terminal.
   

   NOTICE:

   When disconnecting the cable, some systems need to be initialized after the cable is reconnected (HILUX_TGN26 RM000004QR300CX.html).

5. Remove the rear power window regulator switch assembly with rear door armrest base panel.
   

w/o Power Window:

1. Temporarily install the rear door window regulator handle.
   

2. Operate the rear door window regulator so that the rear door glass can be installed.
   

3. Remove the rear door window regulator handle.
   

Install the front side of the rear door glass run.

Apply MP grease to the sliding area of the rear door glass channel as shown in the illustration.

Standard:

Area	Specified Condition
A	155 mm (6.10 in.)
B	30 mm (1.18 in.)

Install the rear door glass by passing it through the cutout of the rear door panel in the direction indicated by the arrow in the illustration.

NOTICE:

Do not damage the door glass.

Install the rear door glass channel to the rear door window regulator as shown in the illustration.

NOTICE:

Do not damage the door glass.

Align the rear door glass run with the rear door window division bar.

Install the rear door glass run together with the rear door window division bar with the 2 bolts.

Finish installing the rear door glass run.

w/ Rear Speaker:

1. Apply new butyl tape to the rear door panel.
   

2. Pass the rear door inside locking cable, rear door lock remote control cable and wire harness through a new rear door service hole cover, and then attach the rear door service hole cover using the reference points on the rear door panel.
   

   Text in Illustration

   *a	Reference Point

   NOTICE:

   1. Securely install the rear door service hole cover to prevent wrinkles and air bubbles.
      
   2. There should be no wrinkles or folds after installing the rear door service hole cover.
      
   3. After installing the rear door service hole cover, check the seal quality.
      

w/o Rear Speaker:

1. Apply new butyl tape to the rear door panel.
   

2. Pass the rear door inside locking cable and rear door lock remote control cable through a new rear door service hole cover, and then attach the rear door service hole cover using the reference points on the rear door panel.
   

   Text in Illustration

   *a	Reference Point

   NOTICE:

   1. Securely install the rear door service hole cover to prevent wrinkles and air bubbles.
      
   2. There should be no wrinkles or folds after installing the rear door service hole cover.
      
   3. After installing the rear door service hole cover, check the seal quality.
      

Install the rear door No. 2 trim bracket with the 2 screws.

Connect the rear door inside locking cable and rear door lock remote control cable to the rear door inside handle.

Attach the 2 guides as indicated by the arrow in the illustration, and then attach the claw to install the rear door inside handle.

Attach the 9 clips to install the rear door trim board.

Install the screw and clip.

Install the door pull handle with the screw.

Connect the connector.

Attach the 2 claws and 2 clips to install the rear power window regulator switch assembly with rear door armrest base panel.