Window Glass. Power Window Regulator Motor (For Front Door) Removal

Vehicle Exterior. Hilux. Tgn26, 36 Kun25, 26, 35, 36 Ggn25

Window Glass. Hilux. Tgn26, 36 Kun25, 26, 35, 36 Ggn25

PRECAUTION
DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
REMOVE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL LH
REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL RH (for Front Passenger Side)
REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH LH
REMOVE DOOR PULL HANDLE
REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH
REMOVE FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY LH
REMOVE FRONT DOOR NO. 1 TRIM BRACKET
REMOVE FRONT DOOR SERVICE HOLE COVER LH
REMOVE FRONT DOOR GLASS SUB-ASSEMBLY LH
REMOVE FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY LH
REMOVE POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

Power Window Regulator Motor (For Front Door) -- Removal

HINT:

Use the same procedure for the RH and LH sides.
The procedure listed below is for the LH side.

1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (HILUX_TGN26 RM000004QR1006X.html).

2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (HILUX_TGN26 RM000004QR3008X.html).

3. REMOVE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL LH

Hilux. Tgn26, 36 Kun25, 26, 35, 36 Ggn25.Window Glass.Power Window Control System (W/ Jam Protection Function).Power Window Regulator Motor (For Front Door) Removal

Using a moulding remover, detach the 2 clips and 4 claws.

Disconnect the connector and remove the power window regulator master switch assembly with front door armrest base panel.
Text in Illustration
*A
for Double Cab
*B
for Single Cab

Text in Illustration
*A	for Double Cab
*B	for Single Cab

4. REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL RH (for Front Passenger Side)

Hilux. Tgn26, 36 Kun25, 26, 35, 36 Ggn25

Using a moulding remover, detach the 2 clips and 4 claws.

Disconnect the connector and remove the power window regulator switch assembly with front door armrest base panel.

5. REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH LH

Detach the 2 clips and remove the front door lower frame bracket garnish.
Text in Illustration
*A
w/o Front No. 2 Speaker
*B
w/ Front No. 2 Speaker

Text in Illustration
*A	w/o Front No. 2 Speaker
*B	w/ Front No. 2 Speaker

6. REMOVE DOOR PULL HANDLE

Remove the screw and door pull handle.

7. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH

for Double Cab:
1. Remove the clip and screw.
  Text in Illustration
  *1
  Clip
  *2
  Screw
2. Detach the 8 clips and remove the front door trim board.

Text in Illustration
*1	Clip
*2	Screw

for Single Cab:
1. Remove the clip and screw.
  Text in Illustration
  *1
  Clip
  *2
  Screw
2. Detach the 9 clips and remove the front door trim board.

Text in Illustration
*1	Clip
*2	Screw

8. REMOVE FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY LH

Detach the claw and 2 guides as indicated by the arrows in the order shown in the illustration.

Disconnect the front door inside locking cable and front door lock remote control cable and remove the front door inside handle.

9. REMOVE FRONT DOOR NO. 1 TRIM BRACKET

Remove the 2 screws and front door No. 1 trim bracket.

10. REMOVE FRONT DOOR SERVICE HOLE COVER LH

Pull out the front door inside locking cable, front door lock remote control cable and wire harness from the front door service hole cover, and then remove the front door service hole cover.
HINT:
Remove any remaining butyl tape from the front door panel.

11. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY LH

w/ Power Window:
1. Temporarily install the power window regulator master switch assembly with front door armrest base panel.
2. Connect the cable to the negative (-) battery terminal.
3. Move the front door glass sub-assembly so that the front door glass bolts can be seen.
4. Disconnect the cable from the negative (-) battery terminal.
  NOTICE:
  When disconnecting the cable, some systems need to be initialized after the cable is reconnected (HILUX_TGN26 RM000004QR3008X.html).
5. Remove the power window regulator master switch assembly with front door armrest base panel.

w/o Power Window:
1. Temporarily install the door window regulator handle.
2. Move the front door glass sub-assembly so that the front door glass bolts can be seen.
3. Remove the door window regulator handle.

Remove the 2 bolts.
NOTICE:
After the bolts are removed, do not allow the front door glass to fall.

Remove the front door glass as indicated by the arrows in the order shown in the illustration.
NOTICE:
Do not damage the front door glass.

12. REMOVE FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY LH

w/ Power Window:
1. Disconnect the connector.
2. Loosen the temporary bolt.
  NOTICE:
  Do not remove the temporary bolt. If the temporary bolt is removed, the front door window regulator may fall and become damaged.
  Text in Illustration
  *1
  Temporary Bolt
3. Remove the 5 bolts and front door window regulator.
4. Remove the temporary bolt from the front door window regulator.

Text in Illustration
*1	Temporary Bolt

w/o Power Window:
1. Loosen the temporary bolt.
  NOTICE:
  Do not remove the temporary bolt. If the temporary bolt is removed, the front door window regulator may fall and become damaged.
  Text in Illustration
  *1
  Temporary Bolt
2. Remove the 4 bolts and front door window regulator.
3. Remove the temporary bolt from the front door window regulator.

Text in Illustration
*1	Temporary Bolt

13. REMOVE POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

Using a T25 "TORX" socket wrench, remove the 3 screws and power window regulator motor assembly LH.