Audio And Visual System (For Radio Receiver Type) Steering Pad Switch Circuit
DESCRIPTION
WIRING DIAGRAM
INSPECTION PROCEDURE
INSPECT STEERING PAD SWITCH ASSEMBLY
INSPECT SPIRAL CABLE SUB-ASSEMBLY
CHECK HARNESS AND CONNECTOR (RADIO RECEIVER - SPIRAL CABLE)
AUDIO AND VISUAL SYSTEM (for Radio Receiver Type) - Steering Pad Switch Circuit |
DESCRIPTION
This circuit sends an operation signal from the steering pad switch assembly to the radio receiver assembly.If there is an open in the circuit, the audio system cannot be operated using the steering pad switch assembly.If there is a short in the circuit, the same condition as when the switch is continuously depressed occurs.Therefore, the radio receiver assembly cannot be operated using the steering pad switch assembly, and the radio receiver assembly itself cannot function.
WIRING DIAGRAM
INSPECTION PROCEDURE
- CAUTION:
- The vehicle is equipped with an SRS (Supplemental Restraint System) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precautionary notice for the SRS (HILUX_TGN26 RM000000KT10E2X.html).
| 1.INSPECT STEERING PAD SWITCH ASSEMBLY |
Remove the steering pad switch assembly (HILUX_TGN26 RM0000033RT06DX.html).
Text in Illustration*A
| w/ Multi-information Display
| -
| -
|
*1
| Volume+ Switch
| *2
| Volume- Switch
|
*3
| Seek- Switch
| *4
| Seek+ Switch
|
*5
| MODE Switch
| -
| -
|
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
| Switch Condition
| Specified Condition
|
z3-10 (AU1) - z3-8 (EAU)
| No switch is pushed
| 95 to 105 kΩ
|
Seek+ switch is pushed
| Below 2.5 Ω
|
Seek- switch is pushed
| 312.6 to 345.5 Ω
|
Volume+ switch is pushed
| 950 to 1050 Ω
|
Volume- switch is pushed
| 2954.5 to 3265.5 Ω
|
z3-9 (AU2) - z3-8 (EAU)
| No switch is pushed
| 95 to 105 kΩ
|
MODE switch is pushed
| Below 2.5 Ω
|
| 2.INSPECT SPIRAL CABLE SUB-ASSEMBLY |
Remove the spiral cable sub-assembly (HILUX_TGN26 RM0000010B200SX.html).
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
| Condition
| Specified Condition
|
8 (EAU) - 4 (EAU)
| Spiral cable is turned 2.5 rotations counterclockwise
| Below 1 Ω
|
Spiral cable is centered
|
Spiral cable is turned 2.5 rotations clockwise
|
10 (AU1) - 6 (AU1)
| Spiral cable is turned 2.5 rotations counterclockwise
|
Spiral cable is centered
|
Spiral cable is turned 2.5 rotations clockwise
|
9 (AU2) - 5 (AU2)
| Spiral cable is turned 2.5 rotations counterclockwise
|
Spiral cable is centered
|
Spiral cable is turned 2.5 rotations clockwise
|
Text in Illustration*a
| Steering Pad Switch Side
|
*b
| Vehicle Side
|
- CAUTION:
- The spiral cable is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable may prevent the airbag from deploying. Be sure to read the Precaution for the SRS (HILUX_TGN26 RM000000KT10E2X.html).
| 3.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER - SPIRAL CABLE) |
Disconnect the G1 radio receiver assembly connector.
Disconnect the G12 spiral cable sub-assembly connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
| Condition
| Specified Condition
|
G1-21 (SW1) - G12-6 (AU1)
| Always
| Below 1 Ω
|
G1-22 (SW2) - G12-5 (AU2)
|
G1-23 (SWG) - G12-4 (EAU)
|
G1-21 (SW1) - Body ground
| Always
| 10 kΩ or higher
|
G1-22 (SW2) - Body ground
|
G1-23 (SWG) - Body ground
|
| | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
