Anti-Lock Brake System Dtc Check / Clear

Brake. Hilux. Tgn26, 36 Kun25, 26, 35, 36 Ggn25
Brake Control Dynamic Control Systems. Hilux. Tgn26, 36 Kun25, 26, 35, 36 Ggn25

  1. DTC CHECK/CLEAR (When Using Intelligent Tester)

  1. DTC CHECK/CLEAR (When Using SST Check Wire)

  1. END OF DTC CHECK/CLEAR

Anti-Lock Brake System -- Dtc Check / Clear



DTC CHECK/CLEAR (When Using Intelligent Tester)

  1. Check for DTCs.

    1. Turn the ignition switch off.

    2. Connect the intelligent tester to the DLC3.

    3. Turn the ignition switch to ON.

    4. Turn the intelligent tester on.

    5. Enter the following menus: Chassis / ABS/VSC/TRC / DTC.

    6. Check the details of the DTCs.

      HINT:
      Refer to the intelligent tester operator's manual for further details.

  2. Clear the DTCs.

    NOTICE:
    Clearing the DTC also clears the freeze frame data.

    1. Turn the ignition switch off.

    2. Connect the intelligent tester to the DLC3.

    3. Turn the ignition switch to ON.

    4. Turn the intelligent tester on.

    5. Enter the following menus: Chassis / ABS/VSC/TRC / DTC.

    6. Clear the DTCs by following the prompts on the intelligent tester.

      HINT:
      Refer to the intelligent tester operator's manual for further details.

DTC CHECK/CLEAR (When Using SST Check Wire)


    Hilux. Tgn26, 36 Kun25, 26, 35, 36 Ggn25.Brake Control Dynamic Control Systems.Anti-Lock Brake System.Anti-Lock Brake System Dtc Check / Clear

  1. Check for DTCs.

    Text in Illustration
    *a
    		Front view of DLC3

    1. Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.

      SST
      09843-18040
      NOTICE:
      Do not connect the incorrect terminals as this will cause damage.

    2. Turn the ignition switch to ON.

    3. Read the DTCs output from the ABS warning light in the combination meter.

      HINT:
      1. When the system is normal, the ABS warning light blinks at 0.25 second intervals (0.25 seconds on and 0.25 seconds off).
      2. When only 1 DTC is output, the light outputs the same code after an interval of 4 seconds. Example: when DTC 21 is output, the light blinks twice, turns off for 1.5 seconds, blinks once, turns off for 4 seconds, and then repeats this output pattern.
      3. When 2 or more DTCs are output, the light outputs the codes with an interval of 2.5 seconds between each different code, and it repeats the output of all codes after an interval of 4 seconds.

    4. Disconnect terminals 13 (TC) and 4 (CG) of the DLC3.



    2. Hilux. Tgn26, 36 Kun25, 26, 35, 36 Ggn25.Brake Control Dynamic Control Systems.Anti-Lock Brake System.Anti-Lock Brake System Dtc Check / Clear

  2. Clear the DTCs.

    Text in Illustration
    *a
    		Front view of DLC3

    1. Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.

      SST
      09843-18040
      NOTICE:
      Do not connect the incorrect terminals as this will cause damage.

    2. Turn the ignition switch to ON.

    3. Clear the DTCs stored in the ECU by depressing the brake pedal 8 times or more within 5 seconds.

    4. Check that the ABS warning light blinks at 0.25 second intervals (0.25 seconds on and 0.25 seconds off).

    5. Remove SST from the terminals of the DLC3.


END OF DTC CHECK/CLEAR

  1. Turn the ignition switch to ON.

  2. Check that the ABS warning light goes off within approximately 3 seconds after turning the ignition switch to ON.