Dtc P0705 Transmission Range Sensor Circuit Malfunction (Prndl Input)

Drivetrain. Hilux. Tgn26, 36 Kun25, 26, 35, 36 Ggn25
A343F Automatic Transmission Transaxle. Hilux. Tgn26, 36 Kun25, 26, 35, 36 Ggn25

DESCRIPTION

MONITOR DESCRIPTION

WIRING DIAGRAM

INSPECTION PROCEDURE

CHECK PARK/NEUTRAL POSITION SWITCH ASSEMBLY (POWER SOURCE)

CHECK HARNESS AND CONNECTOR (NSW TERMINAL VOLTAGE)

INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

INSPECT SHIFT LOCK CONTROL ECU

CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - SHIFT LOCK CONTROL ECU)

CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM)

CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM)

DTC P0705 Transmission Range Sensor Circuit Malfunction (PRNDL Input)


DESCRIPTION

The Park/Neutral Position (PNP) switch detects the shift lever position and sends signals to the ECM.

DTC Code
DTC Detection Condition
Trouble Area
P0705
One of the following conditions is met:
(A) Any 2 or more of the following signals are ON simultaneously (2-trip detection logic):
  1. NSW input signal
  2. R input signal
  3. 2 input signal
  4. L input signal
(B) All signals are OFF simultaneously for NSW, R, 2 and L positions (2-trip detection logic).
(C) Any of the following signals is ON for 2.0 seconds or more with the shift lever in 3 (2-trip detection logic):
  1. NSW input signal
  2. R input signal
  3. 2 input signal
  4. L input signal
  1. Open or short in park/neutral position switch circuit
  2. Park/neutral position switch
  3. Shift lock control ECU (Shift lock control unit assembly)
  4. ECM

MONITOR DESCRIPTION

This DTC indicates a problem with the park/neutral position switch or the wire harness in the park/neutral position switch circuit.
The park/neutral position switch detects the shift lever position and sends a signal to the ECM.
For security, the park/neutral position switch detects the shift lever position so that the engine can be started only when the shift lever is in P or N.
The park/neutral position switch sends a signal to the ECM according to the shift lever position (R, D, 3, 2 or L).
The ECM determines that there is a problem with the switch or related parts if it receives more than 1 position signal simultaneously. The ECM will illuminate the MIL and store the DTC.

WIRING DIAGRAM


Hilux. Tgn26, 36 Kun25, 26, 35, 36 Ggn25.A343F Automatic Transmission Transaxle.Automatic Transmission System. Dtc P0705 Transmission Range Sensor Circuit Malfunction (Prndl Input)


INSPECTION PROCEDURE


DATA LIST
HINT:
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the intelligent tester to the DLC3.

  4. Turn the ignition switch to ON.

  5. Turn the intelligent tester on.

  6. Enter the following menus: Powertrain / Engine and ECT / Data List.

  7. According to the display on the tester, read the Data List.

    Engine and ECT
    Tester Display
    		Measurement Item/Range
    		Normal Condition
    		Diagnostic Note
    Neutral Position SW Signal
    		PNP switch status/
    ON or OFF
    1. Shift lever in P or N: ON
    2. Shift lever not in P or N: OFF
    		When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
    Shift SW Status (R Range)
    		PNP switch status/
    ON or OFF
    1. Shift lever in R: ON
    2. Shift lever not in R: OFF
    		When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
    Shift SW Status (2 Range)
    		PNP switch status/
    ON or OFF
    1. Shift lever in 2: ON
    2. Shift lever not in 2: OFF
    		When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
    Shift SW Status (L Range)
    		PNP switch status/
    ON or OFF
    1. Shift lever in L: ON
    2. Shift lever not in L: OFF
    		When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
    Shift SW Status (3 Range)
    		PNP switch status/
    ON or OFF
    1. Shift lever in 3: ON
    2. Shift lever not in 3: OFF
    		When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
1.CHECK PARK/NEUTRAL POSITION SWITCH ASSEMBLY (POWER SOURCE)


    Hilux. Tgn26, 36 Kun25, 26, 35, 36 Ggn25.A343F Automatic Transmission Transaxle.Automatic Transmission System. Dtc P0705 Transmission Range Sensor Circuit Malfunction (Prndl Input)

  1. Disconnect the C26 park/neutral position switch connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    		Switch Condition
    		Specified Condition
    C26-2 (RB) - Body ground
    		Ignition switch ON
    		11 to 14 V
    C26-2 (RB) - Body ground
    		Ignition switch off
    		Below 1 V
    Text in Illustration
    *a
    		Front view of wire harness connector
    (to Park/Neutral Position Switch)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.CHECK HARNESS AND CONNECTOR (NSW TERMINAL VOLTAGE)


    Hilux. Tgn26, 36 Kun25, 26, 35, 36 Ggn25.A343F Automatic Transmission Transaxle.Automatic Transmission System. Dtc P0705 Transmission Range Sensor Circuit Malfunction (Prndl Input)

  1. Disconnect the C26 park/neutral position switch connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    		Switch Condition
    		Specified Condition
    C26-4 (B) - Body ground
    		Ignition switch ON
    		11 to 14 V
    C26-4 (B) - Body ground
    		Ignition switch off
    		Below 1 V
    Text in Illustration
    *a
    		Front view of wire harness connector
    (to Park/Neutral Position Switch)


NG
Go to step 7
OK


3.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY


    Hilux. Tgn26, 36 Kun25, 26, 35, 36 Ggn25.A343F Automatic Transmission Transaxle.Automatic Transmission System. Dtc P0705 Transmission Range Sensor Circuit Malfunction (Prndl Input)

  1. Disconnect the C26 park/neutral position switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    		Condition
    		Specified Condition
    4 (B) - 5 (L)
    		Shift lever in P
    		Below 1 Ω
    2 (RB) - 1 (RL)
    		Shift lever in R
    		Below 1 Ω
    4 (B) - 5 (L)
    		Shift lever in N
    		Below 1 Ω
    2 (RB) - 7 (DL)
    		Shift lever in D or 3
    		Below 1 Ω
    2 (RB) - 3 (2L)
    		Shift lever in 2
    		Below 1 Ω
    2 (RB) - 8 (LL)
    		Shift lever in L
    		Below 1 Ω
    4 (B) - 5 (L)
    		Shift lever not in P
    		10 kΩ or higher
    2 (RB) - 1 (RL)
    		Shift lever not in R
    		10 kΩ or higher
    4 (B) - 5 (L)
    		Shift lever not in N
    		10 kΩ or higher
    2 (RB) - 7 (DL)
    		Shift lever not in D or 3
    		10 kΩ or higher
    2 (RB) - 3 (2L)
    		Shift lever not in 2
    		10 kΩ or higher
    2 (RB) - 8 (LL)
    		Shift lever not in L
    		10 kΩ or higher
    Text in Illustration
    *a
    		Component without harness connected
    (Park/Neutral Position Switch)


NG
REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY (HILUX_TGN26 RM0000010NC05LX.html)
OK


4.INSPECT SHIFT LOCK CONTROL ECU


    Hilux. Tgn26, 36 Kun25, 26, 35, 36 Ggn25.A343F Automatic Transmission Transaxle.Automatic Transmission System. Dtc P0705 Transmission Range Sensor Circuit Malfunction (Prndl Input)

  1. Disconnect the G37 shift lock control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    		Condition
    		Specified Condition
    3 (AT3) - 9 (NSSD)
    		Shift lever in 3
    		Below 1 Ω
    3 (AT3) - 9 (NSSD)
    		Shift lever in D
    		10 kΩ or higher
    Text in Illustration
    *a
    		Component without harness connected
    (Shift Lock Control ECU)


NG
REPLACE SHIFT LOCK CONTROL ECU (SHIFT LOCK CONTROL UNIT ASSEMBLY) (HILUX_TGN26 RM0000010NQ021X.html)
OK


5.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - SHIFT LOCK CONTROL ECU)


    Hilux. Tgn26, 36 Kun25, 26, 35, 36 Ggn25.A343F Automatic Transmission Transaxle.Automatic Transmission System. Dtc P0705 Transmission Range Sensor Circuit Malfunction (Prndl Input)

  1. Disconnect the G37 shift lock control ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    		Condition
    		Specified Condition
    9 (NSSD) - Body ground
    1. Ignition switch ON
    2. Shift lever in D or 3
    		11 to 14 V
    9 (NSSD) - Body ground
    1. Ignition switch ON
    2. Shift lever not in D or 3
    		Below 1 V
    Text in Illustration
    *a
    		Front view of wire harness connector
    (to Shift Lock Control ECU)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM)


    Hilux. Tgn26, 36 Kun25, 26, 35, 36 Ggn25.A343F Automatic Transmission Transaxle.Automatic Transmission System. Dtc P0705 Transmission Range Sensor Circuit Malfunction (Prndl Input)

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    		Condition
    		Specified Condition
    C97-17 (R) - C98-5 (E1)
    1. Ignition switch ON
    2. Shift lever in R
    		11 to 14 V*
    G146-23 (3) - C98-5 (E1)
    1. Ignition switch ON
    2. Shift lever in 3
    		11 to 14 V
    C97-15 (2) - C98-5 (E1)
    1. Ignition switch ON
    2. Shift lever in 2
    		11 to 14 V
    C97-25 (L) - C98-5 (E1)
    1. Ignition switch ON
    2. Shift lever in L
    		11 to 14 V
    C97-17 (R) - C98-5 (E1)
    1. Ignition switch ON
    2. Shift lever not in R
    		Below 1 V
    G146-23 (3) - C98-5 (E1)
    1. Ignition switch ON
    2. Shift lever not in 3
    		Below 1 V
    C97-15 (2) - C98-5 (E1)
    1. Ignition switch ON
    2. Shift lever not in 2
    		Below 1 V
    C97-25 (L) - C98-5 (E1)
    1. Ignition switch ON
    2. Shift lever not in L
    		Below 1 V
    Text in Illustration
    *a
    		Rear view of wire harness connector
    (to ECM)
    HINT:
    *: The voltage will drop slightly due to the illumination of the back-up light.


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (HILUX_TGN26 RM000000VW2024X.html)

7.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM)

  1. Disconnect the C26 park/neutral position switch connector.

  1. Disconnect the G146 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    		Condition
    		Specified Condition
    C26-4 (B) - G146-24 (NSW)
    		Always
    		Below 1 Ω
    C26-4 (B) - Body ground
    		Always
    		10 kΩ or higher


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (HILUX_TGN26 RM000000VW2024X.html)