Power Window Control System (For Sedan) Rear Power Window Lh Does Not Operate With Rear Power Window Switch Lh
DESCRIPTION
WIRING DIAGRAM
INSPECTION PROCEDURE
CHECK POWER WINDOW REGULATOR SWITCH ASSEMBLY (POWER SOURCE)
INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY
CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH - POWER WINDOW REGULATOR MOTOR)
INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY
CHECK HARNESS AND CONNECTOR (REGULATOR MASTER SWITCH - REGULATOR SWITCH)
INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (REAR LH SWITCH)
POWER WINDOW CONTROL SYSTEM (for Sedan) - Rear Power Window LH does not Operate with Rear Power Window Switch LH |
DESCRIPTION
If the rear LH side manual UP/DOWN function does not operate, a malfunction may exist in the power window regulator motor, power window regulator switch, power window regulator master switch or wire harness.
WIRING DIAGRAM
INSPECTION PROCEDURE
- NOTICE:
- Inspect the fuses for circuits related to this system before performing the following inspection procedure.
1.CHECK POWER WINDOW REGULATOR SWITCH ASSEMBLY (POWER SOURCE) |
Disconnect the I1 power window regulator switch assembly connector.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
| Switch Condition
| Specified Condition
|
I1-3 (B) - Body ground
| Ignition switch ON
| 11 to 14 V
|
Reconnect the power window regulator switch assembly connector.
| REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
2.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY |
Remove the power window regulator switch assembly.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
| Switch Condition
| Specified Condition
|
1 - 2 3 - 4
| UP
| Below 1 Ω
|
4 - 5 1 - 2
| OFF
| Below 1 Ω
|
1 - 3 4 - 5
| DOWN
| Below 1 Ω
|
Reinstall the power window regulator switch assembly.
3.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH - POWER WINDOW REGULATOR MOTOR) |
Disconnect the I1 power window regulator switch assembly connector.
Disconnect the I2 power window regulator motor assembly connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
| Condition
| Specified Condition
|
I1-4 (U) - I2-1 (U)
| Always
| Below 1 Ω
|
I1-4 (U) or I2-1 (U) - Body ground
| Always
| 10 kΩ or higher
|
I1-1 (D) - I2-2 (D)
| Always
| Below 1 Ω
|
I1-1 (D) or I2-2 (D) - Body ground
| Always
| 10 kΩ or higher
|
Reconnect the power window regulator switch assembly connector.
Reconnect the power window regulator motor assembly connector.
| REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
4.INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY |
Remove the power window regulator motor assembly.
Apply battery voltage to connector terminals 1 and 2.
Check that the motor gear rotates smoothly as follows.
- OK:
Measurement Condition
| Specified Condition
|
Battery positive (+) → 1 Battery negative (-) → 2
| Motor gear rotates clockwise
|
Battery positive (+) → 2 Battery negative (-) → 1
| Motor gear rotates counterclockwise
|
Reinstall the power window regulator motor assembly.
5.CHECK HARNESS AND CONNECTOR (REGULATOR MASTER SWITCH - REGULATOR SWITCH) |
Disconnect the G1 power window regulator master switch assembly connector.
Disconnect the I1 power window regulator switch assembly connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
| Condition
| Specified Condition
|
G1-12 (U) - I1-5 (SU)
| Always
| Below 1 Ω
|
G1-12 (U) or I1-5 (SU) - Body ground
| Always
| 10 kΩ or higher
|
G1-13 (D) - I1-2 (SD)
| Always
| Below 1 Ω
|
G1-13 (D) or I1-2 (SD) - Body ground
| Always
| 10 kΩ or higher
|
Reconnect the power window regulator master switch assembly connector.
Reconnect the power window regulator switch assembly connector.
| REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
6.INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (REAR LH SWITCH) |
Remove the power window regulator master switch assembly.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
| Window Lock Switch Condition
| Power Window Switch Condition
| Specified Condition
|
1 (E) - 13 (D) 6 (B) - 12 (U)
| OFF
| UP
| Below 1 Ω
|
1 (E) - 12 (U) 1 (E) - 13 (D)
| OFF
| OFF
| Below 1 Ω
|
1 (E) - 12 (U) 6 (B) - 13 (D)
| OFF
| DOWN
| Below 1 Ω
|
1 (E) - 13 (D)
| ON
| UP
| 10 kΩ or higher
|
6 (B) - 12 (U)
| Below 1 Ω
|
12 (U) - 13 (D)
| ON
| OFF
| Below 1 Ω
|
1 (E) - 12 (U)
| ON
| DOWN
| 10 kΩ or higher
|
6 (B) - 13 (D)
| Below 1 Ω
|
Reinstall the power window regulator master switch assembly.