Roof Headlining (For Hatchback 3 Door) Removal

Remove the deck board.

Disengage the 8 claws and remove the front door scuff plate.

Remove the clip.

Disengage the clip and remove the cowl side trim board.

Remove the front door opening trim weatherstrip.

Disengage the 2 claws and remove the anchor cover.

Remove the bolt and separate the front seat outer belt.

Disengage the 8 clips and 10 claws.

Disengage the 3 guides and remove the quarter trim panel.

Remove the 2 screws and disengage the clip.

Pass the front seat outer belt through the slit in the center pillar upper garnish and remove the center pillar upper garnish.

Disengage the front pillar garnish clip and the clip.

HINT:

The front pillar garnish clip should remain between the front pillar garnish and the pillar.

Using needle nose pliers, turn the front pillar garnish clip 90° and disengage it from the front pillar garnish.

NOTICE:

1. As a pillar garnish clip is reusable, do not remove it from the pillar as long as it is not damaged.
   
2. Replace the front pillar garnish clips with new ones if they are removed from the vehicle.
   

HINT:

Tape the needle-nosed pliers tip before use.

Disengage the 2 guides and remove the front pillar garnish.

for 6 speakers:

1. Disconnect the connector.
   

Protect the curtain shield airbag assembly.

1. Cover the airbag with a cloth or piece of nylon and secure the ends of the cover with tape as shown in the illustration.
   

   NOTICE:

   Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.

Disengage the 2 clips and the 2 guides and remove the front pillar garnish.

for 6 speakers:

1. Disconnect the connector.
   

Using a screwdriver with its tip wrapped in protective tape, disengage the claw.

Disconnect the connector and remove the No. 2 room light assembly.

Disengage the 4 claws and 4 guides and remove the rear floor finish plate.

Remove the bolt.

Disengage the 2 claws and separate the rear seat 3 point type outer belt.

Remove the 3 screws.

Disengage the 3 clips and the 3 claws and remove the deck trim side panel.

Disengage the 5 clips.

Pass the rear seat 3 point type outer belt through the slit in the roof side inner garnish and remove the roof side inner garnish.

Disengage the 4 clips and remove the roof side rail garnish.

Remove the visor shaft from the visor holder.

Remove the 2 screws and the visor.

Turn the visor holder clockwise 45° and disengage the 2 claws to remove the visor holder.

HINT:

Use the same procedure for the LH side and RH side.

Using a moulding remover, disengage the 4 claws and remove the 2 assist grip covers.

Disengage the 2 clips and remove the assist grip.

Using a clip remover, remove the 2 roof headlining service hole covers.

Using a moulding remover, disengage the 4 claws.

Disconnect the connector and remove the map light assembly.

Disengage the 2 claws and open the slip joint cover.

Remove the bolt and separate the rear center seat outer belt.

for front pillar RH side:

1. Disconnect the connector
   

2. Using a clip remover, remove the 4 clamps.
   

for front pillar LH side:

1. Disconnect the connector
   

2. Using a clip remover, remove the 4 clamps.
   

for rear pillar RH side:

1. Disconnect the connector
   

2. Using a clip remover, remove the 3 clamps.
   

Disengage the 2 claws.

Using a clip remover, remove the 3 clips.

Disengage the 2 hooks.

Remove the roof headlining from the vehicle through the back door as shown in the illustration.

NOTICE:

Do not damage the roof headlining assembly or body interior.