Front Airbag Sensor (For Sedan) Removal

Vehicle Interior. Yaris. Ncp93, 131
Supplemental Restraint Systems. Yaris. Ncp93, 131

  1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

  2. REMOVE FRONT SPOILER COVER (w/ Front Spoiler)

  3. REMOVE FRONT BUMPER COVER (w/ Large Front Spoiler)

  4. REMOVE FRONT BUMPER COVER (w/ Small Front Spoiler)

  5. REMOVE FRONT BUMPER COVER (w/o Front Spoiler)

  6. REMOVE FRONT AIRBAG SENSOR

Front Airbag Sensor (For Sedan) -- Removal


CAUTION:
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing (YARIS_NCP93 RM000000KT10D1X.html).
HINT:
The procedure described below is for the LH side. Use the same procedure for both the RH and LH sides, unless otherwise specified.


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


2. REMOVE FRONT SPOILER COVER (w/ Front Spoiler)


    Yaris. Ncp93, 131

  1. Remove the 2 screws, the 10 bolts and the front spoiler cover.



3. REMOVE FRONT BUMPER COVER (w/ Large Front Spoiler)


    Yaris. Ncp93, 131.Supplemental Restraint Systems.Airbag System (For Sedan).Front Airbag Sensor (For Sedan) Removal

  1. Apply protective tape, as shown in the illustration.



    Yaris. Ncp93, 131

  1. Remove the 9 bolts and the 7 screws.

  1. Remove the 2 screw grommets.

  1. Remove the 6 clips.



    Yaris. Ncp93, 131

  1. Disengage the 6 claws and remove the front bumper cover.

  1. Disconnect the connectors.

    HINT:
    If the vehicle is equipped with fog lights, disconnect the connector.


    Yaris. Ncp93, 131

  1. Remove the 2 clips, the screw grommet and the 6 spring nuts.



4. REMOVE FRONT BUMPER COVER (w/ Small Front Spoiler)


    Yaris. Ncp93, 131.Supplemental Restraint Systems.Airbag System (For Sedan).Front Airbag Sensor (For Sedan) Removal

  1. Apply protective tape, as shown in the illustration.



    Yaris. Ncp93, 131

  1. Remove the 5 screws and the 3 bolts.

  1. Remove the 2 screw grommets.

  1. Remove the 6 clips.



    Yaris. Ncp93, 131

  1. Disengage the 6 claws and remove the front bumper cover.

  1. Disconnect the connectors.

    HINT:
    If the vehicle is equipped with fog lights, disconnect the connectors.


    Yaris. Ncp93, 131

  1. Remove the 2 clips, the screw grommet and the 10 spring nuts.



5. REMOVE FRONT BUMPER COVER (w/o Front Spoiler)


    Yaris. Ncp93, 131.Supplemental Restraint Systems.Airbag System (For Sedan).Front Airbag Sensor (For Sedan) Removal

  1. Apply protective tape, as shown in the illustration.



    Yaris. Ncp93, 131

  1. Remove the 5 screws and the 3 bolts.

  1. Remove the 2 screw grommets.

  1. Remove the 6 clips.



    Yaris. Ncp93, 131

  1. Disengage the 6 claws and remove the front bumper cover.

  1. Disconnect the connectors.

    HINT:
    If the vehicle is equipped with fog lights, disconnect the connectors.


    Yaris. Ncp93, 131

  1. Remove the 2 clips, the screw grommet and the 10 spring nuts.



6. REMOVE FRONT AIRBAG SENSOR


Yaris. Ncp93, 131.Supplemental Restraint Systems.Airbag System (For Sedan).Front Airbag Sensor (For Sedan) Removal
CAUTION:
Confirm that the negative battery terminal is disconnected before performing the operation. Even an impact to only the airbag sensor will cause the airbag to deploy.

  1. Remove the 2 bolts.

  1. Disengage the 2 claws and remove the front airbag sensor.



    Yaris. Ncp93, 131.Supplemental Restraint Systems.Airbag System (For Sedan).Front Airbag Sensor (For Sedan) Removal

  1. Disconnect the airbag connector.

    NOTICE:
    1. Do not disconnect the airbag connector by pulling the wire harness.
    2. Release the lock without holding the upper side of CPA.

    1. While pushing the housing, slide only the CPA backward (from a provisionally locked state).

    2. Detach the connector while pushing the housing in the provisionally locked state.

      NOTICE:
      1. Do not disconnect the airbag connector by pulling the wire harness.
      2. Release the lock without holding the upper side of CPA.


      3. Yaris. Ncp93, 131

    3. After detaching the connector, confirm that the CPA protrudes beyond the rear of the housing.