Sfi System (For Sedan) Readiness Monitor Drive Pattern

Engine Hybrid System. Yaris. Ncp93, 131
1Nz-Fe Engine Control. Yaris. Ncp93, 131

  1. PURPOSE OF READINESS TESTS

  1. CATALYST MONITOR (ACTIVE AIR-FUEL RATIO CONTROL TYPE)

  1. VVT SYSTEM MONITOR

  1. EVAP SYSTEM MONITOR (KEY OFF TYPE)

  1. AIR-FUEL RATIO (A/F) AND HEATED OXYGEN (HO2) SENSOR MONITORS (ACTIVE AIR-FUEL RATIO CONTROL TYPE)

  1. AIR-FUEL RATIO (A/F) AND HEATED OXYGEN (HO2) SENSOR HEATER MONITORS (FRONT A/F AND REAR HO2 SENSOR TYPE)

Sfi System (For Sedan) -- Readiness Monitor Drive Pattern



PURPOSE OF READINESS TESTS
  1. The On-Board Diagnostic (OBD II) system is designed to monitor the performance of emission related components, and indicate any detected abnormalities with DTCs (Diagnostic Trouble Codes). Since various components need to be monitored during different driving conditions, the OBD II system is designed to run separate monitoring programs called Readiness Monitors.
  2. To view the monitor status, enter the following menus: Powertrain / Engine and ECT / Monitor / Current Monitor / Current.
  3. When the Readiness Monitor status reads Complete, the necessary conditions have been met for running the performance tests for that Readiness Monitor.
  4. A generic OBD II scan tool can also be used to view the Readiness Monitor status.
HINT:
Many state Inspection and Maintenance (I/M) programs require a vehicle's Readiness Monitor status to show Complete before beginning emission tests.
  1. The Readiness Monitor will be reset to Incomplete if:
  1. The ECM has lost battery power or blown a fuse.
  2. DTCs have been cleared.
  3. The conditions for running the Readiness Monitor have not been met.
  1. If the Readiness Monitor status shows Incomplete, follow the appropriate Readiness Monitor Drive Pattern to change the status to Complete.
CAUTION:
Strictly observe posted speed limits, traffic laws, and road conditions when performing these drive patterns.
NOTICE:
These drive patterns represent the fastest method of satisfying all conditions necessary to achieve complete status for each specific Readiness Monitor.
In the event of a drive pattern being interrupted (possibly due to factors such as traffic conditions), the drive pattern can be resumed. In most cases, the Readiness Monitor will still achieve complete status upon completion of the drive pattern.
To ensure completion of the Readiness Monitors, avoid sudden changes in vehicle load and speed (driving up and down hills and/or sudden acceleration).

CATALYST MONITOR (ACTIVE AIR-FUEL RATIO CONTROL TYPE)

  1. Refer to Confirmation Driving Pattern [P0420] (YARIS_NCP93 RM000000TMD09GX_14.html).


VVT SYSTEM MONITOR

  1. Refer to Confirmation Driving Pattern [P0011] (YARIS_NCP93 RM000000PDU0JZX_12.html).


EVAP SYSTEM MONITOR (KEY OFF TYPE)

  1. Refer to Confirmation Driving Pattern [EVAP System] (YARIS_NCP93 RM0000011IO01OX_14.html).


AIR-FUEL RATIO (A/F) AND HEATED OXYGEN (HO2) SENSOR MONITORS (ACTIVE AIR-FUEL RATIO CONTROL TYPE)

  1. Refer to Confirmation Driving Pattern [P0136] (YARIS_NCP93 RM000000TEO09JX_09.html).

  2. Refer to Confirmation Driving Pattern [P2195] (YARIS_NCP93 RM000000WC40K6X_08.html).


AIR-FUEL RATIO (A/F) AND HEATED OXYGEN (HO2) SENSOR HEATER MONITORS (FRONT A/F AND REAR HO2 SENSOR TYPE)

  1. Refer to Confirmation Driving Pattern [P0031] (YARIS_NCP93 RM000000WC10KOX_12.html).

  2. Refer to Confirmation Driving Pattern [P0037] (YARIS_NCP93 RM000000PFA0KQX_16.html).