Fuel Lid Lock Control Cable Assembly Installation

Engage the 7 clamps.

Engage the 2 claws and connect the fuel lid lock control cable sub-assembly.

Connect the fuel lid lock control cable sub-assembly.

Install the luggage door lock open lever sub-assembly with the bolt.

Torque:

5.5 N*m{56 kgf*cm, 49 in.*lbf}

Install the inner luggage compartment trim cover LH with the 4 clips.

Engage the 8 claws and install the rear floor finish plate.

Install the 2 clips.

Engage the 2 guides and 2 claws, and install the roof side inner garnish board LH.

Engage the 2 claws, 2 clips and guide, and install the rear seat side garnish LH.

Place the rear seatback assembly LH in the cabin.

NOTICE:

Be careful not to damage the vehicle body.

Install the rear seatback assembly LH with the 2 bolts.

Torque:

18 N*m{184 kgf*cm, 13 ft.*lbf}

Install the 2 rear seatback clips.

Attach the rear hook of the seat cushion to the seatback.

Attach the 2 front hooks of the seat cushion to the vehicle body.

Confirm that the seat cushion is firmly installed.

NOTICE:

When installing the seat cushion, make sure that the seat belt buckle is not under the seat cushion.

Install the spare wheel cover.

Engage the 2 claws and 2 clips, and install the lower center pillar garnish LH.

Install the floor end of the front seat outer belt assembly with the bolt.

Torque:

41 N*m{420 kgf*cm, 30 ft.*lbf}

Check if the ELR locks.

NOTICE:

The check should be performed with the outer belt assembly installed.

1. With the belt assembly installed, check that the belt locks when it is pulled out quickly.
   

Engage the 3 claws and install the lap belt outer anchor cover.

for TMC Made:

1. Align the alignment mark (pink) on the weatherstrip and the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip LH.
   

   NOTICE:

   After installation, check that the corners fit correctly.

for TMMC Made:

1. Align the alignment mark (red) on the weatherstrip and the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip LH.
   

   NOTICE:

   After installation, check that the corners fit correctly.

Engage the 6 claws and install the rear door scuff plate LH.

Align the alignment mark (yellow) on the weatherstrip and the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip LH.

NOTICE:

After installation, check that the corners fit correctly.

Engage the guide and clip, and install the cowl side trim board LH.

Engage the 8 claws and install the front door scuff plate LH.

Place the front seat assembly in the cabin.

NOTICE:

Be careful not to damage the vehicle body.

Connect the connectors under the seat.

Temporarily install the front seat assembly with the 4 bolts.

Lift up the seat track adjusting handle and move the seat to the rearmost position.

Tighten the 2 bolts on the front side of the seat.

Torque:

37 N*m{377 kgf*cm, 27 ft.*lbf}

HINT:

Tighten the bolts in the order indicated in the illustration.

Lift up the seat track adjusting handle and move the seat to the foremost position.

Tighten the 2 bolts on the rear side of the seat.

Torque:

37 N*m{377 kgf*cm, 27 ft.*lbf}

HINT:

Tighten the bolts in the order indicated in the illustration.

While sliding the front seat, check that the left and right adjusters move together smoothly and lock simultaneously.
If the seat adjusters do not lock simultaneously, loosen the bolts securing the seat to adjust the adjuster position.

Lift up the seat track adjusting handle and move the seat to the rearmost position.

Engage the 2 claws and install the inner seat track cover.

Engage the 2 claws and install the outer seat track cover.

Place the front seat assembly in the cabin.

NOTICE:

Be careful not to damage the vehicle body.

Connect the connectors under the seat.

Connect the cable to the negative (-) battery terminal.

Temporarily install the front seat assembly with the 4 bolts.

Operate the power seat switch knob and move the seat to the rearmost position.

Tighten the 2 bolts on the front side of the seat.

Torque:

37 N*m{377 kgf*cm, 27 ft.*lbf}

HINT:

Tighten the bolts in the order indicated in the illustration.

Operate the power seat switch knob and move the seat to the foremost position.

Tighten the 2 bolts on the rear side of the seat.

Torque:

37 N*m{377 kgf*cm, 27 ft.*lbf}

HINT:

Tighten the bolts in the order indicated in the illustration.

Engage the 2 claws and install the inner seat track cover.

Engage the 2 claws and install the outer seat track cover.

Inspect the power seat operation.