Power Window Control System Front Passenger Side Power Window Does Not Operate With Front Passenger Side Power Window Switch

DESCRIPTION

WIRING DIAGRAM

INSPECTION PROCEDURE

CHECK HARNESS AND CONNECTOR (POWER SOURCE)

INSPECT POWER WINDOW SWITCH (FRONT PASSENGER SIDE)

CHECK HARNESS AND CONNECTOR (SWITCH (PASSENGER SIDE) - MOTOR (PASSENGER SIDE))

INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY (FRONT PASSENGER SIDE)

CHECK HARNESS AND CONNECTOR (MASTER SWITCH - SWITCH (FRONT PASSENGER SIDE))

DESCRIPTION

WIRING DIAGRAM

INSPECTION PROCEDURE

1. Disconnect the power window switch (front passenger side) connector.
   

2. Measure the voltage according to the value(s) in the table below.
   

   Standard Voltage:

   Tester Connection	Switch Condition	Specified Condition
   H7-3 (B) - Body ground	Ignition switch ON	11 to 14 V

1. Remove the power window switch (COROLLA_ZRE142 RM000002YA6014X.html).
   

2. Measure the resistance according to the value(s) in the table below.
   

   Standard Resistance:

   Tester Connection	Switch Condition	Specified Condition
   3 (B) - 4 (U) 2 (SD) - 1 (D)	UP	Below 1 Ω
   5 (SU) - 4 (U) 2 (SD) - 1 (D)	OFF	Below 1 Ω
   5 (SU) - 4 (U) 3 (B) - 1 (D)	DOWN	Below 1 Ω

1. Disconnect the power window regulator motor assembly (front passenger side) connector.
   

2. Measure the resistance according to the value(s) in the table below.
   

   Standard Resistance:

   Tester Connection	Condition	Specified Condition
   H7-1 (D) - H8-1 (D)	Always	Below 1 Ω
   H7-4 (U) - H8-2 (U)	Always	Below 1 Ω
   H7-1 (D) - Body ground	Always	10 kΩ or higher
   H7-4 (U) - Body ground	Always	10 kΩ or higher

1. Remove the power window regulator motor assembly (COROLLA_ZRE142 RM000002YF201SX.html).
   

2. Check power window regulator motor operation:
   

   1. Apply battery voltage to connector terminals 1 and 2.
      

      NOTICE:

      Do not apply battery voltage to any terminals except terminals 1 and 2.

   2. Check that the motor gear rotates smoothly as follows.
      

      OK:

      Measurement Condition	Specified Condition
      Battery positive (+) → 1 (D) Battery negative (-) → 2 (U)	Motor gear rotates clockwise
      Battery positive (+) → 2 (U) Battery negative (-) → 1 (D)	Motor gear rotates counterclockwise

3. Check PTC operation:
   

   NOTICE:

   This check must be performed with the power window regulator and door glass installed on the vehicle.

   1. Install the power window regulator motor (COROLLA_ZRE142 RM000002YF001UX.html).
      

   
   
   

   2. Connect an electrical tester DC 400 A probe to the wire harness of terminal 2.
      

      NOTICE:

      Match the arrow mark of the probe with the direction of the current flow.

   3. Fully close the door glass by pulling up the power window switch. Wait for approximately 60 seconds.
      

   4. Continue to pull up the power window switch and measure how long it takes for the electrical current to change from a range of 16 to 28 A to approximately 1 A (current shut-off inspection).
      

      Standard:

      4 to 90 seconds
      

   5. Wait for 60 seconds after the previous step, and then push down the power window switch (passenger side).
      

      OK:

      The passenger side window goes down.
      

1. Disconnect the power window master switch connector.
   

2. Disconnect the power window switch (front passenger side) connector.
   

3. Measure the resistance according to the value(s) in the table below.
   

   Standard Resistance:

   Tester Connection	Condition	Specified Condition
   I3-16 (U) - H7-5 (SU)	Always	Below 1 Ω
   I3-15 (D) - H7-2 (SD)	Always	Below 1 Ω
   I3-16 (U) - Body ground	Always	10 kΩ or higher
   I3-15 (D) - Body ground	Always	10 kΩ or higher