Steering Wheel Installation

for Type A:

1. Install the 2 steering wheel pad attaching screws to the lower steering wheel boss cover.
   





2. Engage the 2 claws to install the lower steering wheel boss cover to the steering wheel sub-assembly.
   





3. Install the 2 screws.
   

for Type B:

1. Engage the 2 claws to install the lower steering wheel boss cover to the steering wheel sub-assembly.
   

2. Engage the 2 pins.
   

Install the switch as shown in the illustration.

Install the 2 screws.

Connect the connector.

for Type A:

1. Engage the 2 pins to install the No. 1 steering wheel ornament to the steering wheel sub-assembly.
   





2. Install the screw.
   

   Torque:

   2.4 N*m{24 kgf*cm, 21 in.*lbf}

for Type B:

1. Engage the 2 pins and claw to install the No. 1 steering wheel ornament to the steering wheel sub-assembly.
   

2. Install the screw.
   

   Torque:

   2.4 N*m{24 kgf*cm, 21 in.*lbf}

for Type A:

1. Engage the 2 pins and install the steering pad switch LH.
   

2. Install the screw.
   

   Torque:

   2.4 N*m{24 kgf*cm, 21 in.*lbf}

3. Engage the clamp.
   

4. Connect the connector to the spiral cable.
   

for Type B:

1. Engage the 2 pins and claw to install the steering pad switch LH.
   

2. Install the screw.
   

   Torque:

   2.4 N*m{24 kgf*cm, 21 in.*lbf}

3. Connect the connector to the spiral cable.
   

for Type A:

1. Engage the 2 pins and install the steering pad switch assembly.
   

2. Install the screw.
   

   Torque:

   2.4 N*m{24 kgf*cm, 21 in.*lbf}

3. Engage the clamp.
   

4. Engage the 2 pins and install the steering pad switch.
   

5. Install the screw.
   

   Torque:

   2.4 N*m{24 kgf*cm, 21 in.*lbf}

6. Engage the clamp.
   

7. Connect the connector to the spiral cable.
   

for Type B:

1. Engage the 2 pins and claw to install the steering pad switch assembly.
   

2. Install the screw.
   

   Torque:

   2.4 N*m{24 kgf*cm, 21 in.*lbf}

3. Engage the 2 pins and claw to install the steering pad switch.
   

4. Install the screw.
   

   Torque:

   2.4 N*m{24 kgf*cm, 21 in.*lbf}

5. Connect the connector to the spiral cable.
   

Check that the ignition switch is off.

Check that the cable is disconnected from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

Rotate the spiral cable counterclockwise slowly by hand until it stops.

NOTICE:

Do not turn the spiral cable using the airbag wire harness.

Rotate the spiral cable clockwise approximately 2.5 turns to align the marks.

NOTICE:

Do not turn the spiral cable using the airbag wire harness.

HINT:

The spiral cable will rotate approximately 2.5 turns to both the left and right from the center.

for Type A:

1. Align the matchmarks on the steering wheel assembly and steering main shaft.
   

   Text in Illustration

   *a

   Matchmark

2. Install the steering wheel assembly set nut.
   

   Torque:

   50 N*m{510 kgf*cm, 37 ft.*lbf}

3. Connect the connectors to the spiral cable sub-assembly.
   

for Type B:

1. Align the matchmarks on the steering wheel assembly and steering main shaft.
   

   Text in Illustration

   *a

   Matchmark

2. Install the steering wheel assembly set nut.
   

   Torque:

   50 N*m{510 kgf*cm, 37 ft.*lbf}

3. Connect the connectors to the spiral cable sub-assembly.