Shift Lever Installation

Install the shift lever assembly with the 4 bolts.

Torque:

12 N*m{122 kgf*cm, 9 ft.*lbf}

Install the 3 wire harness clamps to the shift lever assembly.

Connect the 2 connectors to the shift lever assembly.

Turn the nut of the transmission control cable 180° counterclockwise. While holding the nut in place, push in the stopper until the stopper clicks twice.

Install the outer part of the transmission control cable to the shift lever retainer. Check that the spring is positioned at "A" and push in the stopper.

HINT:

If the stopper cannot be pushed in, slightly turn the nut clockwise and then push in the stopper again.

Push the 2 claws together at the top of the transmission control cable lock piece. While holding the 2 claws together, push the 2 lugs on the bottom of the lock piece toward each other and upward to pull out the lock piece.

Install the cable end to the shift lever assembly.

NOTICE:

1. Check that the lock piece is pulled up.
   

1. Install the cable end all the way to the base of the pin.
   

Push the lock piece into the adjuster case.

NOTICE:

Securely push in the lock piece until it locks.

Install the 2 screws.

Install the console box assembly with the 2 bolts and 2 screws.

Install the console box carpet.

Engage the 6 clips and 2 guides to install the upper console panel sub-assembly.

Engage the guide.

Engage the 3 claws and install the front No. 1 console box insert.

Engage the guide.

Engage the 3 claws and install the front No. 2 console box insert.

Connect the connector.

Engage the 2 claws.

Install the instrument panel box assembly with the 2 screws <B>.

Engage the guide.

Engage the 2 claws and 2 clips, and install the center No.1 instrument cluster finish panel assembly.

Turn the shift lever knob clockwise and install the shift lever knob sub-assembly.

Engage the 3 claws and clip, and then install the lower instrument panel finish panel LH.

Engage the 3 claws and clip, and then install the lower instrument panel finish panel RH.

When moving the shift lever from P to R with the ignition switch ON and the brake pedal depressed, make sure that the shift lever moves smoothly and correctly into position.

Start the engine and make sure that the vehicle moves forward when moving the shift lever from N to D and moves rearward when moving the shift lever to R. If the operation cannot be performed as specified, inspect the park/neutral position switch assembly and check the shift lever assembly installation condition.

Apply the parking brake and move the shift lever to N.

Remove the console box assembly (COROLLA_ZRE142 RM000002XV501QX.html).

Disconnect the end of the transmission control cable assembly from the shift lever assembly.

Using a screwdriver, pull out the stopper of the transmission control cable.

NOTICE:

Do not remove the stopper. If the stopper is removed, reinstall it to its original position.

Rotate the nut counterclockwise approximately 180°, and while holding the nut in place, disconnect the transmission control cable from the shift lever retainer.

NOTICE:

Do not over-rotate the nut as it will come off the internal spring and the transmission control cable will not be reusable.

Push the 2 claws together at the top of the transmission control cable lock piece. While holding the 2 claws together, push the 2 lugs on the bottom of the lock piece toward each other and upward to pull out the lock piece.

Turn the nut of the transmission control cable 180° counterclockwise. While holding the nut in place, push in the stopper until the stopper clicks twice.

Install the outer part of the transmission control cable to the shift lever retainer. Check that the spring is positioned at "A" and push in the stopper.

HINT:

If the stopper cannot be pushed in, slightly turn the nut clockwise and then push in the stopper again.

Install the cable end to the shift lever assembly.

NOTICE:

1. Check that the lock piece is pulled up.
   
2. Install the cable end all the way to the base of the pin.
   

Push the lock piece into the adjuster case.

NOTICE:

Securely push in the lock piece until it locks.

After adjusting the shift lever position, check the operation and function of the shift lever. If there is a problem, adjust the position again.

Install the console box assembly (COROLLA_ZRE142 RM000002XV301QX.html).