Oil Pump Removal

Remove the 2 front wiper arm head caps.

Remove the nut and the front wiper arm and blade assembly LH.

Remove the nut and the front wiper arm and blade assembly RH.

Disengage the 7 clips and remove the hood to cowl top seal.

Disengage the clip and 14 claws, and remove the center No. 1 cowl top ventilator louver.

Disengage the clip and 8 claws, and remove the cowl top ventilator louver LH.

Disconnect the connector.

Remove the 2 bolts and the windshield wiper motor and link assembly.

Disengage the clamp and bend the water guard plate RH as shown in the illustration.

Disengage the clamp and bend the No. 1 heater air duct splash shield seal.

Disengage the clamp.

Remove the 12 bolts and outer cowl top panel.

Remove the 2 nuts and suspension tower damper assembly.

Remove the 2 nuts and No. 1 engine cover sub-assembly.

Loosen the lower radiator drain cock plug.

CAUTION:

Do not loosen the lower radiator drain cock plug while the engine and radiator are still hot.

Pressurized, hot engine coolant and steam may be released and cause serious burns.

HINT:

Collect the coolant in a container and dispose of it according to the regulations in your area.

Remove the radiator cap.

Loosen the cylinder block drain cock plug.

Remove the oil filler cap.

Remove the oil drain plug and drain the oil into a container.

Clean and install the oil drain plug with a new gasket.

Torque:

25 N*m{255 kgf*cm, 18 ft.*lbf}

Remove the 4 bolts and 2 compression springs.

Remove the center exhaust pipe assembly from the 2 exhaust pipe supports.

Remove the 2 gaskets.

Disconnect the heated oxygen sensor connector.

Remove the 2 bolts, 2 compression springs and front exhaust pipe assembly.

Remove the gasket from the exhaust manifold.

Using SST, slowly turn the V-ribbed belt tensioner clockwise.

SST

09216-42010(09216-04010)

Remove the V-ribbed belt from each pulley and slowly return the tensioner.

NOTICE:

1. Make sure that SST and other tools are set to the tensioner securely.
   
2. When compressing the V-ribbed belt tensioner, slowly turn the tensioner.
   
3. Be careful not to pinch your fingers between the parts.
   

Disconnect the generator connector.

Remove the nut and disconnect the wire harness from terminal B.

Separate the 2 wire harness clamps.

Remove the 2 bolts and generator assembly.

Remove the bolt and wire harness clamp bracket.

Disconnect the No. 1 radiator hose from the cylinder head.

Disconnect the outlet heater water hose.

Disconnect the inlet heater water hose.

Remove the 3 bolts and separate the radiator reserve tank assembly.

Disconnect the mass air flow meter connector.

Separate the 2 wire harness clamps.

Disconnect the No. 1 vacuum switching valve connector and the 2 vacuum hoses.

Disconnect the ventilation hose.

Loosen the No. 1 air cleaner hose clamp, release the 3 air cleaner assembly clamps and remove the air cleaner cap sub-assembly with No. 1 hose.

Disconnect the 2 water by-pass hoses.

Disconnect the throttle body assembly connector.

Remove the 4 bolts and throttle body assembly.

Remove the gasket from the intake manifold.

Disconnect the 4 ignition coil connectors.

Remove the 4 bolts and 4 ignition coils.

Remove the 4 spark plugs.

Remove the 2 ventilation hoses from the cylinder head cover sub-assembly.

Remove the 2 bolts and separate the 2 wire harness brackets.

Remove the 8 bolts and 2 nuts, then remove the cylinder head cover sub-assembly and gasket.

Remove the bolt and engine oil level dipstick guide.

Remove the O-ring from the engine oil level dipstick guide.

Remove the fuel tube from the fuel hose clamp.

Remove the fuel pipe clamp.

Wipe off any dirt on the fuel tube connector.

Hold the fuel tube connector, and then install SST.

SST

09268-21011

Turn SST to align the retainer inside the fuel tube connector with the chamfered part of SST.

Insert SST into the fuel tube and hold it. Then push the fuel tube connector toward SST.

Mount the retainer of the fuel tube connector onto the chamfered part of SST.

Slide SST and fuel tube connector together towards the fuel tube until they make a "click" sound, and then disconnect the fuel tube.

Drain the fuel remaining inside the fuel tube.

Cover the fuel tube and fuel pipe with a plastic bag to protect the disconnected part.

Remove the 2 wire harness clamps.

Disconnect the 4 fuel injector connectors.

Remove the 2 bolts, then remove the fuel delivery pipe together with the 4 fuel injectors.

NOTICE:

Be careful not to drop the fuel injectors when removing the fuel delivery pipe.

Remove the 2 delivery pipe spacers from the cylinder head.

Remove the 4 insulators from the cylinder head.

Remove the bolt and the vacuum hose clamp.

Disconnect the camshaft timing oil control valve connector.

Remove the bolt and the camshaft timing oil control valve assembly.

Remove the O-ring from the camshaft timing oil control valve assembly.

Disconnect the union to connector tube hose from the No. 2 hose to hose tube.

Disconnect the camshaft timing oil control valve connector.

Remove the wire harness clamp.

Remove the union to connector tube hose from the vacuum hose clamp.

Remove the 5 bolts, 2 nuts and intake manifold.

Remove the gasket from the intake manifold.

Remove the No. 1 intake manifold insulator.

Remove the bolt, nut and manifold stay.

Remove the bolt, nut and No. 2 manifold stay.

Remove the 4 bolts and No. 1 exhaust manifold heat insulator.

Remove the 5 nuts and exhaust manifold converter sub-assembly.

Remove the gasket.

Place a wooden block between a floor jack and the engine, then support the engine using the floor jack.

Remove the 4 bolts and 2 nuts, then remove the engine mounting insulator sub-assembly RH.

NOTICE:

Do not apply excessive force to the return tube when removing the engine mounting insulator sub-assembly RH.

HINT:

Keep clearance by lowering the engine using the floor jack when removing the front engine mounting insulator.

Loosen the 2 bolts and remove the idler pulley sub-assembly with the 2 bolts.

Install the No. 1 and No. 2 engine hangers with new bolts.

Torque:

38 N*m{387 kgf*cm, 28 ft.*lbf}

Attach the sling device to the engine hangers and chain block.

Remove the 12 bolts and 2 nuts.

Insert the blade of oil pan seal cutter between the crankcase, chain cover and oil pan, then cut through the applied sealer and remove the oil pan.

NOTICE:

Be careful not to damage the contact surface of the crankcase, chain cover or oil pan.

Turn the crankshaft pulley until the groove and the timing mark "0" on the timing chain cover are aligned.

Check that each timing mark on the camshaft timing gear and sprocket is aligned with the timing marks located on the No. 1 and No. 2 bearing caps as shown in the illustration.
If not, turn the crankshaft 1 revolution (360°) to align the timing marks as above.

Using SST, hold the crankshaft pulley in place and loosen the pulley bolt.

SST

09213-54015(91651-60855)
09330-00021

Using SST, remove the crankshaft pulley.

SST

09950-50013(09951-05010,09952-05010,09953-05020,09954-05021)
09950-40011(09957-04010)

HINT:

If necessary, remove the pulley and pulley bolt using SST.

Remove the 2 nuts, No. 1 chain tensioner assembly and gasket.

NOTICE:

Do not turn the crankshaft without the No. 1 chain tensioner assembly.

Lift the engine upward.

NOTICE:

Do not lift the engine more than necessary.

Remove the bolt, nut and V-ribbed belt tensioner assembly.

Disconnect the crank position sensor connector.

Separate the crank position sensor connector clamp and wire harness.

Remove the bolt and crank position sensor.

Remove the 3 bolts and transverse engine engine mounting bracket.

Using an E10 "TORX" socket, remove the stud bolt for the V-ribbed belt tensioner.

Remove the 12 bolts and 2 nuts.

Remove the timing chain cover by prying the portions between the timing chain cover, cylinder head and cylinder block with a screwdriver.

NOTICE:

Be careful not to damage the contact surfaces of the timing chain cover, cylinder head and cylinder block.

HINT:

Tape the screwdriver tip before use.

Place the timing chain cover on wooden blocks.

Using a screwdriver, pry out the oil seal.

NOTICE:

Do not damage the surface of the oil seal press fit hole.

HINT:

Tape the screwdriver tip before use.

Remove the No. 1 crankshaft position sensor plate.

Remove the bolt and timing chain guide.

Remove the bolt and chain tensioner slipper.

Remove the 2 bolts and No. 1 chain vibration damper.

Remove the crankshaft timing gear or sprocket from the crankshaft.

Turn the crankshaft 90° counterclockwise to align the adjusting hole on the oil pump drive shaft sprocket with the groove on the oil pump.

Insert a 4 mm diameter bar into the adjusting hole of the oil pump drive shaft sprocket to lock the gear in position, and then remove the nut.

Remove the bolt, chain tensioner plate and spring.

Remove the oil pump drive sprocket, oil pump drive shaft sprocket and No. 2 chain.

Remove the 3 bolts, oil pump and gasket.