Dtc P0607 Control Module Performance

Engine Hybrid System. Corolla. Zre142 Aze141
2Az-Fe Engine Control. Corolla. Zre142 Aze141

MONITOR DESCRIPTION

MONITOR STRATEGY

TYPICAL ENABLING CONDITIONS

TYPICAL MALFUNCTION THRESHOLDS

CONFIRMATION DRIVING PATTERN

INSPECTION PROCEDURE

CHECK ANY OTHER DTCS OUTPUT

INSPECT DTC (P0136, P0137 OR P0138)

CHECK FOR EXHAUST GAS LEAK

PERFORM CONFIRMATION DRIVING PATTERN

INSPECT DTC (P0136, P0137 OR P0138)

INSPECT ECM

DTC P0607 Control Module Performance


MONITOR DESCRIPTION

The ECM continuously monitors its internal processors (CPUs) and Heated Oxygen (HO2) sensor transistors. This self-check ensures that the ECM is functioning properly.

DTC No.
DTC Detection Condition
Trouble Area
P0607
Either of the following conditions is met (1 trip detection logic):
  1. ECM CPUs malfunction
  2. Heated Oxygen (HO2) sensor transistors (built into ECM) malfunction
  1. Exhaust gas leak
  2. Heated oxygen sensor
  3. ECM
For Mexico models:
ECM CPU error
  1. ECM

MONITOR STRATEGY


Related DTCs
P0607: Control Module Performance
Required Sensors/Components (Main)
ECM
Required Sensors/Components (Related)
Heated oxygen sensor
Frequency of Operation
Continuous
Duration
60 seconds
MIL Operation
Immediate
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs not present
None
Engine
Running
Estimated heated oxygen sensor temperature
450 to 750°C (842 to 1382°F)

TYPICAL MALFUNCTION THRESHOLDS


Heated oxygen sensor transistors
Fail

CONFIRMATION DRIVING PATTERN


Corolla. Zre142 Aze141.2Az-Fe Engine Control.Sfi System. Dtc P0607 Control Module Performance

  1. Stop the engine for 30 minutes or more [A].
  2. Connect the Techstream to the DLC3.
  3. Turn the ignition switch to ON and turn the Techstream on [B].
  4. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  5. Turn the ignition switch off and wait for at least 30 seconds.
  6. Turn the ignition switch to ON and turn the Techstream on [C].
  7. Start the engine and wait 2 minutes [D].
  8. Warm up the engine until the engine coolant temperature is 75°C (167°F) or higher [E].
  9. Idle the engine for 1 minute [F].
  10. Accelerate the vehicle to 80 km/h (50 mph) and stop the vehicle [G].
    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.
  11. Drive the vehicle at 56 to 80 km/h (35 to 50 mph) for 5 minutes or more [H].
    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.
  12. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [I].
  13. Read the pending DTCs.
    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.
  14. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  15. Input the DTC: P0607, P0136, P0137 or P0138.
  16. Check the DTC judgment result.

    Techstream Display
    		Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit
    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform steps [E] through [I] again.
  17. If no pending DTC is output, perform a universal trip and check for permanent DTCs (COROLLA_ZRE142 RM000000PDK0ZBX.html).
    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
1.CHECK ANY OTHER DTCS OUTPUT

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs (COROLLA_ZRE142 RM000000PDK0ZBX.html).

    Result:

    Result
    		Proceed to
    P0607 and P0136, P0137 or P0138
    		A
    P0607
    		B


B
Go to step 3
A


2.INSPECT DTC (P0136, P0137 OR P0138)

  1. Inspect the P0136, P0137 or P0138 flowchart.

    HINT:
    1. If P0136 is output, troubleshoot for that DTC first (COROLLA_ZRE142 RM000000WBY0H0X.html). Then proceed to "INSPECT ECM".
    2. If P0137 is output, troubleshoot for that DTC first (COROLLA_ZRE142 RM000000WBY0H0X.html). Then proceed to "INSPECT ECM".
    3. If P0138 is output, troubleshoot for that DTC first (COROLLA_ZRE142 RM000000WBY0H0X.html). Then proceed to "INSPECT ECM".
    4. If DTC P0607 and P0136, P0137 or P0138 are output, the output voltage of the heated oxygen sensor may remain close to 0 V or become high (around 1 V or more).


NEXT
Go to step 6

3.CHECK FOR EXHAUST GAS LEAK

  1. Allow the engine to idle and rev the engine.

  1. Check for exhaust gas leaks around the heated oxygen sensor.
    If any exhaust gas leaks are present, repair it and proceed to "PERFORM CONFIRMATION DRIVING PATTERN". If no exhaust gas leaks are present, proceed to "PERFORM CONFIRMATION DRIVING PATTERN".

    HINT:
    1. If no exhaust gas leaks are present, a malfunction in the heated oxygen sensor circuit is suspected.
    2. If any exhaust gas leaks are present around the heated oxygen sensor, noise appears in the output voltage of the heated oxygen sensor.

NEXT


4.PERFORM CONFIRMATION DRIVING PATTERN

Corolla. Zre142 Aze141.2Az-Fe Engine Control.Sfi System. Dtc P0607 Control Module Performance

  1. Clear the DTC (COROLLA_ZRE142 RM000000PDK0ZBX.html).

  1. Connect the Techstream to the DLC3.

  1. Start the engine.

  1. Turn the Techstream on.

  1. Warm up the engine until the engine coolant temperature becomes 75° (167°F) or more.

  1. Perform the driving pattern.

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

    1. Accelerate the vehicle until 50 mph (80 km/h) and stop the vehicle.

    2. Drive the vehicle by 37 to 50 mph (60 to 80 km/h) for 5 minutes or more.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.

    Result:

    Result
    		Proceed to
    P0607 and P0136, P0137 or P0138
    		A
    P0607
    		B
    No output
    		C


B
REPLACE ECM (COROLLA_ZRE142 RM000002WT402ZX.html)

C
Go to step 6
A


5.INSPECT DTC (P0136, P0137 OR P0138)

  1. Inspect the P0136, P0137 or P0138 flowchart.

    HINT:
    1. If P0136 is output, troubleshoot for that DTC first (COROLLA_ZRE142 RM000000WBY0H0X.html). Then proceed to "INSPECT ECM".
    2. If P0137 is output, troubleshoot for that DTC first (COROLLA_ZRE142 RM000000WBY0H0X.html). Then proceed to "INSPECT ECM".
    3. If P0138 is output, troubleshoot for that DTC first (COROLLA_ZRE142 RM000000WBY0H0X.html). Then proceed to "INSPECT ECM".
    4. If DTC P0607 and P0136, P0137 or P0138 are output, the output voltage of the heated oxygen sensor may remain close to 0 V or become high (around 1 V or more).

NEXT


6.INSPECT ECM

  1. Clear the DTC (COROLLA_ZRE142 RM000000PDK0ZBX.html).

  1. Stop the engine and wait for 30 minutes.

  1. Connect the Techstream to the DLC3.

  1. Start the engine and allow it to idle for 2 minutes.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs (COROLLA_ZRE142 RM000000PDK0ZBX.html).

    Result:

    Result
    		Proceed to
    No output
    		A
    P0607
    		B


B
REPLACE ECM (COROLLA_ZRE142 RM000002WT402ZX.html)
A

END