Radio Antenna Cord Installation

Apply new double-sided tape.

1. Remove the double-sided tape from the roof headlining assembly.
   

2. Peel off the appropriate amount of new double-sided tape. Be careful not to touch the adhesive surface.
   

3. Apply the double-sided tape to the roof headlining while aligning the tape with the markings on the roof headlining assembly.
   

4. Peel off the backing sheet from the double-sided tape.
   

Install the antenna cord to the roof headlining assembly from the front of the vehicle.

Put the strips of the tape back to the positions shown in the illustration in order to secure the antenna cord to the roof headlining assembly.

HINT:

1. If the tape is no longer sticky, use other tape, such as packing tape, that has enough adhesion to secure the antenna cord to the roof headlining assembly.
   
2. For the right front corner of the roof headlining assembly, align the marking tape on the antenna cord with the protrusion of the roof headlining, and wrap tape around the antenna cord and roof headlining assembly once or twice to securely hold them.
   
3. For the right rear corner of the roof headlining assembly, align the marking tape on the antenna cord with the rear edge of the roof headlining, and secure the antenna cord to the roof headlining assembly with tape.
   
4. For the part of the antenna cord near the center of the roof headlining assembly, position the marking tape on the antenna cord within the area indicated by the marking line. Secure the antenna cord to the roof headlining assembly with tape as shown in the illustration. (without sliding roof)
   

Pull the roof headlining assembly into the vehicle through the rear left door.

Engage the 4 clips.

Connect the antenna cord sub-assembly connector and engage the clamp to the rear pillar RH.

Connect the antenna cord sub-assembly connector and engage each clamp to the front pillar RH.

Install the radio setting condenser to the front pillar RH with the bolt.

Connect the No. 1 roof wire connector and engage each clamp to the front pillar LH.

Pull the roof headlining assembly into the vehicle through the rear left door.

Engage the hook, 4 clips, and 2 fasteners.

Connect the sliding roof drive gear connector.

Connect the antenna cord sub-assembly connector and engage the clamp to the rear pillar RH.

Connect the antenna cord sub-assembly connector and engage each clamp to the front pillar RH.

Install the radio setting condenser to the front pillar RH with the bolt.

Connect the No. 1 roof wire connector and engage each clamp to the front pillar LH.

Engage the 2 claws.

Using a screwdriver, turn the pin of each sunshade trim holder 90°to install the sunshade trim holders.

Align the paint mark on the inner surface of the opening trim moulding with the notch of the roof headlining, and install the sun roof opening trim moulding so that joining point of the opening trim is on the left side of the vehicle as shown in the illustration.

NOTICE:

After installation, check that the corners fit correctly.

Push the light bulb holder in the direction indicated by the arrow in the illustration to engage the claw.

Engage the 4 claws.

Engage the 6 claws and install the spot light assembly.

Engage the 4 claws and install the room light switch base to the No. 1 room light assembly.

Engage the 4 claws.

Engage the 4 claws and install the lens cover.

Assemble the front assist grip sub-assembly as shown in the illustration.

Install the front assist grip sub-assembly.

HINT:

Use the same procedures for the RH side and the LH side.

Engage the 2 claws.

Push in the visor holder and turn it approximately 45°as shown in the illustration.

Engage the 2 clips and install the visor assembly LH.

Engage the 4 claws and install the visor bracket cover.

Connect the connectors.

Engage the 2 claws and 2 clips, and then install the roof console box assembly.

Remove the protective cover.

Install a new clip <A> on the front pillar garnish LH.

Engage the 2 claws and 2 clips, then install the front pillar garnish LH.

Remove the protective cover.

Install a new clip <A> on the front pillar garnish RH.

Engage the 2 claws and 2 clips, then install the front pillar garnish RH.

Engage the 5 clips and 2 claws, then install the roof side inner garnish LH.

Engage the clip.

Install the upper center pillar garnish LH with the bolt.

Engage the 2 claws and 2 clips, then install the lower center pillar garnish LH.

Install the floor end of the front seat outer belt assembly LH with the bolt.

Torque:

42 N*m{428 kgf*cm, 31 ft.*lbf}

Engage the 3 claws and install the lap belt outer anchor cover.

Install the front door opening trim weatherstrip LH as shown in the illustration.

NOTICE:

After installation, check that the corners fit correctly.

Engage the 2 clips.

Install the cowl side trim sub-assembly LH with the cowl side trim clip.

Engage the 7 claws and 3 clips, then install the front door scuff plate LH.

Install the front door opening trim weatherstrip RH as shown in the illustration.

NOTICE:

After installation, check that the corners fit correctly.

Engage the 3 claws to install the rear door inner glass weatherstrip.

Engage the claw to install the No. 1 door scuff plate clamp.

Connect each connector.

Engage the rear door trim board with the 4 clips of the rear door inner glass weatherstrip.

Engage the 7 clips to install the rear door trim board to the rear door panel.

Install the 3 screws.

Engage the 6 claws and install the door assist grip cover.

Engage the 3 claws to install the rear door inside handle bezel plug.

Install the rear seat reclining control cable.

Engage the 2 clips and claw and then install the reclining remote control lever sub-assembly.

Install the bolt.

Torque:

18 N*m{184 kgf*cm, 13 ft.*lbf}

Adjust the control lever to set the rear reclining adjuster assembly to its upper most position.

Pull plate A toward the front of the vehicle to lock the plate.

Install the rear door opening trim weatherstrip LH as shown in the illustration.

NOTICE:

After installation, check that the corners fit correctly.

Engage the 5 claws and 2 clips, then install the rear door scuff plate LH.

Install the rear door opening trim weatherstrip RH as shown in the illustration.

NOTICE:

After installation, check that the corners fit correctly.

Install the center seatback assembly with the 2 bolts.

Torque:

18 N*m{184 kgf*cm, 13 ft.*lbf}

Install the separate type rear seatback assembly LH with the 2bolts and 2 nuts.

Torque:

18 N*m{184 kgf*cm, 13 ft.*lbf}

Engage the 3 clamps and install the cover.

Install the 2 rear seat belts.

Install the separate type rear seatback assembly RH with the 2 bolts and 2 nuts.

Torque:

18 N*m{184 kgf*cm, 13 ft.*lbf}

Engage the 3 clamps and install the cover.

Install the rear seat belt.

Install the rear side seatback assembly with the bolt.

Torque:

18 N*m{184 kgf*cm, 13 ft.*lbf}

Install the separate type rear seatback assembly with the 2 bolts.

Torque:

18 N*m{184 kgf*cm, 13 ft.*lbf}

Install the separate type rear seat back assembly with the 2 bolts.

Torque:

18 N*m{184 kgf*cm, 13 ft.*lbf}

Attach the front hooks of the bench type rear seat cushion assembly to the vehicle body.

Confirm that the seat cushion is firmly installed.

NOTICE:

When installing the bench type rear seat cushion assembly, make sure that the seat belt buckle is not under the bench type rear seat cushion assembly.

Place the seat in the cabin.

Connect the connectors under the seat.

Connect the cable to the negative (-) battery terminal.

Move the front seat assembly fully forward by operating the slide and vertical power seat switch knob.

NOTICE:

Check that the seat is locked.

Temporarily install the front side of the front seat assembly with the 2 bolts.

Move the front seat assembly fully forward by operating the slide and vertical power seat switch knob.

NOTICE:

Check that the seat is locked.

Temporarily install the rear side of the front seat assembly with the 2 bolts.

Move the front seat assembly to the rearmost position by operating the slide and vertical power seat switch knob.

NOTICE:

Check that the seat is locked.

Fully tighten the 2 bolts on the front side of the front seat assembly in the order of the inner side bolt and then the outer side bolt.

Torque:

37 N*m{377 kgf*cm, 27 ft.*lbf}

Move the front seat assembly fully forward by operating the slide and vertical power seat switch knob.

NOTICE:

Check that the seat is locked.

Fully tighten the 2 bolts on the rear side of the front seat assembly in the order of the inner side bolt and then the outer side bolt.

Torque:

37 N*m{377 kgf*cm, 27 ft.*lbf}

Slide the inner seat track bracket cover along the seat rail toward the front of the vehicle. Engage claw A to the seat rail.

Push the inner seat track bracket cover to engage claw B.

Slide the seat track cover along the seat rail toward the front of the vehicle. Engage claw A to the seat rail.

Push the seat track cover to engage claw B.

Place the front seat assembly in the vehicle and align the adjuster pin with the hole on the vehicle side.

Connect the connector and clamp.

Move the front seat assembly to the rearmost position by operating the slide handle.

NOTICE:

Check that the seat is locked.

Temporarily install the front seat track bracket with the 2 bolts.

Move the front seat assembly fully forward by operating the slide handle.

NOTICE:

Check that the seat is locked.

Temporarily install the rear seat track bracket with the 2 bolts.

Move the front seat assembly to the rearmost position by operating the slide handle.

NOTICE:

Check that the seat is locked.

Fully tighten the 2 bolts on the front seat track bracket in the order of the inner side bolt and then the outer side bolt.

Torque:

37 N*m{377 kgf*cm, 27 ft.*lbf}

Move the front seat assembly fully forward by operating the slide handle.

NOTICE:

Check that the seat is locked.

Fully tighten the 2 bolts on the rear seat track bracket in the order of the inner side bolt and then the outer side bolt.

Torque:

37 N*m{377 kgf*cm, 27 ft.*lbf}

Slide the inner seat track bracket cover along the seat rail toward the front of the vehicle. Engage claw A to the seat rail.

Push the seat track bracket cover inner to engage claw B.

Slide the seat track cover along the seat rail toward the front of the vehicle. Engage claw A to the seat rail.

Push the seat track cover to engage claw B.

Engage the 6 clamps and clip and install the No. 2 antenna cord sub-assembly.

Engage the 6 clamps and clip and install the No. 2 antenna cord sub-assembly.

Install the No. 2 heater to register duct with the 2 screws <F>.

Install the No. 3 heater to register duct with the 3 screws <F>.

Install the No. 1 heater to register duct with the 3 screws <F>.

Install the defroster nozzle assembly with the 3 screws <F>.

Install the side No. 2 defroster nozzle duct with the screw <F>.

Install the side No. 1 defroster nozzle duct with the screw <F>.

Engage the 5 claws.

NOTICE:

Do not allow the wire harness to get caught in the claws.

Install the 2 bolts <H> or <O> and 2 nuts <C> or <I>.

Engage each clamp.

Install the bolt <J>.

Torque:

7.0 N*m{71 kgf*cm, 62 in.*lbf}

Install the 2 passenger airbag bolts <K>.

Torque:

20 N*m{204 kgf*cm, 15 ft.*lbf}

Connect each connector and install the instrument panel safety pad assembly.

with Plasmacluster:

1. Connect the connector.
   
   

   
   
   
   

Connect the connector (yellow colored one).

Connect each connector.

Engage the 4 guides.

Engage the 8 clips and install the No. 1 defroster nozzle garnish.

Connect the connector.

Install the front No. 2 speaker assembly with the 2 bolts.

Engage the 2 guides.

Engage the 6 claws and the 2 clips to install the instrument panel No. 1 speaker panel sub-assembly.

Engage the 4 clips and install the instrument panel No. 1 register assembly.

Remove the protective cover.

Install a new clip <A> on the front pillar garnish LH.

Engage the 2 claws and 2 clips, then install the front pillar garnish LH.

Engage the 2 guides.

Engage the 6 claws and the 2 clips to install the instrument panel No. 2 speaker panel sub-assembly.

Engage the 4 clips and install the instrument panel No. 3 register assembly.

Remove the protective cover.

Install a new clip <A> on the front pillar garnish RH.

Engage the 2 claws and 2 clips, then install the front pillar garnish RH.

Engage the clip.

Install the No. 1 console box insert front with the 3 screws <F>.

Engage the clip.

Install the No. 2 console box insert front with the 3 screws <F>.

Install the 2 screws <F>.

Install the console box assembly with the 2 bolts <G>.

Install the console box carpet.

Install the console box pocket.

Connect the connector.

Engage the 6 clips.

Install the radio tuner opening cover with heater control panel assembly with the 4 bolts <N>.

Connect each connector.

Engage the 4 clips.

Install the radio receiver with heater control panel assembly with the 4 bolts.

Connect the connector.

Engage the 7 clips and install the instrument panel No. 2 register assembly.

Connect each connector.

Engage the 2 claws and 2 clips.

Install the lower instrument cluster finish panel center sub-assembly with the 2 screws <F>.

Connect the connector and engage the clamp.

Engage the 3 claws and 5 clips to install the upper console rear panel sub-assembly.

Engage the 3 claws and 5 clips to install the upper console rear panel sub-assembly.

with Seat Heater System:

1. Connect each connector.
   

Engage the 6 claws and the 3 clips to install the floor shift position indicator housing sub-assembly.

Engage the 2 claws and the 5 clips to install the upper console panel as shown in the illustration.

Engage the 2 clips and install the No. 2 instrument cluster finish panel garnish.

Engage the 2 clips and install the No. 1 instrument cluster finish panel garnish.

Install the shift lever knob sub-assembly.

Install the shift lever knob sub-assembly.

Engage the 3 claws and 3 clips.

Install the 4 screws <B>.

Install the lower instrument panel sub-assembly with the bolt <A>.

Engage the 4 claws and 2 guides and install the instrument panel No. 2 under cover.

Connect each connector.

Install the combination meter assembly with the 4 screws <E>.

Engage the guide and the 4 claws.

Install the instrument cluster finish panel with the 2 clips.

Engage the 2 claws and 2 clips to install the lower instrument panel finish panel.

Connect each connector.

Engage the 3 claws and 2 clips to install the No. 1 instrument panel sub-assembly.

Install the turn signal switch assembly with spiral cable sub-assembly to the steering column assembly with the clamp.

Connect the connectors to the turn signal switch assembly with spiral cable sub-assembly.

Check that the ignition switch is off.

Check that the battery negative (-) cable is disconnected.

CAUTION:

Wait for 90 seconds after disconnecting the cable to prevent airbag deployment.

Rotate the spiral cable counterclockwise slowly by hand until it feels firm.

NOTICE:

Do not turn the spiral cable by the airbag wire harness.

Rotate the spiral cable clockwise approximately 2.5 turns to align the marks.

NOTICE:

Do not turn the spiral cable by the airbag wire harness.

HINT:

The spiral cable will rotate approximately 2.5 turns to both the left and right from the center.

Engage the claw and install the upper steering column cover.

Engage the 2 claws and install the lower steering column cover.

Install the steering column cover with the 2 screws <D>.

Torque:

2.0 N*m{20 kgf*cm, 18 in.*lbf}

Install the air hose and connect the connector.

Engage the 2 claws and the DLC3.

Engage the claw and the 4 clips.

Instal the lower instrument panel finish panel LH with the screw <B> and bolt <A>.

Engage the 2 clips.

Install the cowl side trim sub-assembly LH with the cowl side trim clip.

Engage the 7 claws and 3 clips, then install the front door scuff plate LH.

Align the matchmarks on the steering wheel assembly and steering main shaft.

Install the steering wheel assembly set nut.

Torque:

50 N*m{510 kgf*cm, 37 ft.*lbf}

Connect the connectors to the spiral cable sub-assembly.

Check that the ignition switch is off.

Check that the battery negative (-) terminal is disconnected.

CAUTION:

Wait for 90 seconds after disconnecting the cable to prevent airbag deployment.

Support the steering pad with one hand.

Connect the 2 airbag connectors to the steering pad.

NOTICE:

When handling the airbag connector, take care not to damage the airbag wire harness.

Connect the horn connector to the steering pad.

Confirm that the circumference groove of the "TORX" screw fits in the screw case, and place the steering pad onto the steering wheel assembly.

Using a "TORX" socket (T30), tighten the 2 "TORX" screws.

Torque:

8.8 N*m{90 kgf*cm, 78 in.*lbf}

Engage the claw and install the No. 3 lower steering wheel cover.

Engage the claw and install the No. 2 lower steering wheel cover.

With the steering pad installed on the vehicle, perform a visual check. If there are any defects as mentioned below, replace the steering pad with a new one:

1. Cuts, minute cracks or marked discoloration on the steering pad top surface or in the grooved portion.
   

Make sure that the horn sounds.

HINT:

If the horn does not sound, inspect the horn system (CAMRY_ACV40 RM0000016F501NX.html).