High Mounted Stop Light Assembly Installation

Connect the connector.

Install the center stop light set with the 2 screws.

Torque:

1.6 N*m{16 kgf*cm, 14 in.*lbf}

Pass the 3 rear seat belt floor anchors through the package tray trim panel assembly.

Engage the 4 clips and 5 claws and install the package tray trim panel assembly.

Connect the connector.

Pass the 3 rear seat belt floor anchors through the package tray trim panel assembly.

Engage the 4 clips and 5 claws and install the package tray trim panel assembly.

Connect the connector.

Engage the 4 claws and install the rear seat shoulder belt hole cover.

Engage the 4 claws and install the rear seat shoulder belt cover.

HINT:

Use the same procedures for the RH side and the LH side.

Install the floor end of the rear seat outer belt assembly with the bolt.

Torque:

42 N*m{428 kgf*cm, 31 ft.*lbf}

NOTICE:

Do not allow the anchor part of the rear seat outer belt assembly to overlap the protruding parts of the floor panel.

Check if the ELR locks.

NOTICE:

The check should be performed with the outer belt assembly installed.

1. With the belt assembly installed, check that the belt locks when it is pulled out quickly.
   

Install the floor end of the rear seat outer belt assembly with the bolt.

Torque:

42 N*m{428 kgf*cm, 31 ft.*lbf}

NOTICE:

Do not allow the anchor part of the rear seat outer belt assembly to overlap the protruding parts of the floor panel.

Check if the ELR locks.

NOTICE:

The check should be performed with the outer belt assembly installed.

1. With the belt assembly installed, check that the belt locks when it is pulled out quickly.
   

Engage the 5 clips and 2 claws, then install the roof side inner garnish LH.

Install the floor end of the rear seat inner with center belt assembly LH with the bolt.

Torque:

42 N*m{428 kgf*cm, 31 ft.*lbf}

NOTICE:

Do not allow the anchor part of the rear seat inner with center belt assembly LH to overlap the protruding parts of the floor panel.

Check if the ELR locks.

NOTICE:

The check should be performed with the outer belt assembly installed.

1. With the belt assembly installed, check that the belt locks when it is pulled out quickly.
   

Install the child restraint seat anchor bracket sub-assembly with the 2 nuts.

Torque:

18 N*m{184 kgf*cm, 13 ft.*lbf}

Install the rear seat reclining control cable.

Engage the 2 clips and claw and then install the reclining remote control lever sub-assembly.

Install the bolt.

Torque:

18 N*m{184 kgf*cm, 13 ft.*lbf}

Adjust the control lever to set the rear reclining adjuster assembly to its upper most position.

Pull plate A toward the front of the vehicle to lock the plate.

Install the rear door opening trim weatherstrip LH as shown in the illustration.

NOTICE:

After installation, check that the corners fit correctly.

Engage the 5 claws and 2 clips, then install the rear door scuff plate LH.

Install the rear door opening trim weatherstrip RH as shown in the illustration.

NOTICE:

After installation, check that the corners fit correctly.

Install the center seatback assembly with the 2 bolts.

Torque:

18 N*m{184 kgf*cm, 13 ft.*lbf}

Install the separate type rear seatback assembly LH with the 2bolts and 2 nuts.

Torque:

18 N*m{184 kgf*cm, 13 ft.*lbf}

Engage the 3 clamps and install the cover.

Install the 2 rear seat belts.

Install the separate type rear seatback assembly RH with the 2 bolts and 2 nuts.

Torque:

18 N*m{184 kgf*cm, 13 ft.*lbf}

Engage the 3 clamps and install the cover.

Install the rear seat belt.

Install the rear side seatback assembly with the bolt.

Torque:

18 N*m{184 kgf*cm, 13 ft.*lbf}

Install the separate type rear seatback assembly with the 2 bolts.

Torque:

18 N*m{184 kgf*cm, 13 ft.*lbf}

Install the separate type rear seat back assembly with the 2 bolts.

Torque:

18 N*m{184 kgf*cm, 13 ft.*lbf}

Attach the front hooks of the bench type rear seat cushion assembly to the vehicle body.

Confirm that the seat cushion is firmly installed.

NOTICE:

When installing the bench type rear seat cushion assembly, make sure that the seat belt buckle is not under the bench type rear seat cushion assembly.