Engine Immobiliser System (W/O Entry And Start System) Data List / Active Test

Securities. Camry. Acv40 Gsv40
Engine Immobiliser. Camry. Acv40 Gsv40

  1. READ DATA LIST

  1. PERFORM ACTIVE TEST

Engine Immobiliser System (W/O Entry And Start System) -- Data List / Active Test



READ DATA LIST
HINT:
Using the DATA LIST displayed on the intelligent tester, the values of the switches, sensors, actuators, etc. can be checked without part removal. Reading the DATA LIST as the first step in troubleshooting is one way to shorten labor time.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the ignition switch to the ON position.

  3. Read the DATA LIST according to the display on the tester.

    IMMOBILISER:
    Tester Display
    		Measurement Item/Range
    		Normal Condition
    		Diagnostic Note
    Key SW
    		Unlock warning switch signal/ON or OFF
    		ON: Key is in ignition key cylinder
    OFF: No key is in ignition key cylinder
    		-
    IG SW
    		Ignition switch signal/ON or OFF
    		ON: Ignition switch ON or START
    OFF: Ignition switch ACC or OFF
    		-
    Immobiliser
    		Immobiliser system status/SET or UNSET
    		UNSET: Ignition switch ON
    SET: Without key
    		-
    Permit (Start)
    		Permit (Start) signal/OK or NG
    		NG: No permission for engine start
    OK: Engine start permission
    		-
    Response
    		Transponder chip data/NG or OK
    		NG: Data error
    OK: Data OK
    		-
    Frame Error
    		Transponder chip data/NG or OK
    		NG: Data error
    OK: Data OK
    		-
    Different Serial Number
    		Transponder chip data/NG or OK
    		NG: Data error
    OK: Data OK
    		-
    Different Encrypt Code
    		Transponder chip data/NG or OK
    		NG: Data error
    OK: Data OK
    		-
    Abnormal Status
    		Transponder chip data/NG or OK
    		NG: Data error
    OK: Data OK
    		-
    Bcc Malfunction
    		Transponder chip data/NG or OK
    		NG: Incorrect data being sent
    OK: Correct data being sent
    		-
    Sub Key
    		Sub key code signal/NOMATCH or MATCH
    		NOMATCH: Non-matching sub key code is sent
    MATCH: Sub key code is sent
    		-
    Master Key
    		Master key code signal/NOMATCH or MATCH
    		NOMATCH: Non-matching master key code is sent
    MATCH: Master key code is sent
    		-
    Transponder S-Code
    		Number of registered sub key/min. 0, max. 15
    		Number of registered sub key
    		-
    Transponder M-Code
    		Number of registered master key/min. 0, max. 15
    		Number of registered master key
    		-
    Reg Code Space Full
    		Memory space for key codes registration/NOT FULL or FULL
    		NOT FULL: More key code registration possible
    FULL: No more key code registration possible
    		-
    +B
    		Power source/BRAKE or NORMAL
    		BRAKE: Power source open
    NORMAL: Power source normal
    		-
    Antenna Coil Status
    		Antenna coil condition/NORMAL or FAIL
    		NORMAL: Antenna coil is normal
    FAIL: Antenna coil is malfunctioning
    		-


PERFORM ACTIVE TEST
HINT:
Performing the intelligent tester ACTIVE TEST allows a relay, VSV, actuator and other items to be operated without removing any parts. Performing the ACTIVE TEST early in troubleshooting is one way to shorten labor time. The DATA LIST can be displayed during the ACTIVE TEST.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the ignition switch to the ON position.

  3. Perform the ACTIVE TEST according to the display on the tester.

    IMMOBILISER:
    Tester Display
    		Test Part
    		Control Range
    		Diagnostic Note
    Security Indic
    		Turn security indicator
    		ON/OFF
    		-