Curtain Shield Airbag Assembly Installation

Check that the ignition switch is off.

Check that the battery negative (-) terminal is disconnected.

CAUTION:

Wait for 90 seconds after disconnecting the cable to prevent airbag deployment.

Install 4 new clips and 4 new spacers to the curtain shield airbag assembly as shown in the illustration.

NOTICE:

1. Do not push in the pin.
   
2. Make sure that the clips are installed in the correct direction.
   
3. Make sure that the spacers are installed properly, in the correct direction, and that they are not damaged.
   

Install the curtain shield airbag assembly with 5 new bolts.

Torque:

11 N*m{112 kgf*cm, 8 ft.*lbf}

NOTICE:

Do not twist the curtain shield airbag assembly when installing it.

Install the 4 clips with the curtain shield airbag assembly to the body panel as shown in the illustration.

NOTICE:

Make sure that the pins of the clips are pushed in firmly.

Mark the clips.

HINT:

Mark the clips to make sure that they are not reused.

Connect the connector.

NOTICE:

When handling the airbag connector, take care not to damage the airbag wire harness.

Pull the roof headlining assembly into the vehicle through the rear left door.

Engage the 4 clips.

Connect the antenna cord sub-assembly connector and engage the clamp to the rear pillar RH.

Connect the antenna cord sub-assembly connector and engage each clamp to the front pillar RH.

Install the radio setting condenser to the front pillar RH with the bolt.

Connect the No. 1 roof wire connector and engage each clamp to the front pillar LH.

Pull the roof headlining assembly into the vehicle through the rear left door.

Engage the hook, 4 clips, and 2 fasteners.

Connect the sliding roof drive gear connector.

Connect the antenna cord sub-assembly connector and engage the clamp to the rear pillar RH.

Connect the antenna cord sub-assembly connector and engage each clamp to the front pillar RH.

Install the radio setting condenser to the front pillar RH with the bolt.

Connect the No. 1 roof wire connector and engage each clamp to the front pillar LH.

Engage the 2 claws.

Using a screwdriver, turn the pin of each sunshade trim holder 90°to install the sunshade trim holders.

Align the paint mark on the inner surface of the opening trim moulding with the notch of the roof headlining, and install the sun roof opening trim moulding so that joining point of the opening trim is on the left side of the vehicle as shown in the illustration.

NOTICE:

After installation, check that the corners fit correctly.

Push the light bulb holder in the direction indicated by the arrow in the illustration to engage the claw.

Engage the 4 claws.

Engage the 6 claws and install the spot light assembly.

Engage the 4 claws and install the room light switch base to the No. 1 room light assembly.

Engage the 4 claws.

Engage the 4 claws and install the lens cover.

Assemble the front assist grip sub-assembly as shown in the illustration.

Install the front assist grip sub-assembly.

HINT:

Use the same procedures for the RH side and the LH side.

Engage the 2 claws.

Push in the visor holder and turn it approximately 45°as shown in the illustration.

Engage the 2 clips and install the visor assembly LH.

Engage the 4 claws and install the visor bracket cover.

Connect the connectors.

Engage the 2 claws and 2 clips, and then install the roof console box assembly.

Remove the protective cover.

Install a new clip <A> on the front pillar garnish LH.

Engage the 2 claws and 2 clips, then install the front pillar garnish LH.

Engage the 5 clips and 2 claws, then install the roof side inner garnish LH.

Engage the clip.

Install the upper center pillar garnish LH with the bolt.

Engage the 2 claws and 2 clips, then install the lower center pillar garnish LH.

Install the floor end of the front seat outer belt assembly LH with the bolt.

Torque:

42 N*m{428 kgf*cm, 31 ft.*lbf}

Engage the 3 claws and install the lap belt outer anchor cover.

Install the front door opening trim weatherstrip LH as shown in the illustration.

NOTICE:

After installation, check that the corners fit correctly.

Engage the 2 clips.

Install the cowl side trim sub-assembly LH with the cowl side trim clip.

Engage the 7 claws and 3 clips, then install the front door scuff plate LH.

Install the front door opening trim weatherstrip RH as shown in the illustration.

NOTICE:

After installation, check that the corners fit correctly.

Engage the 3 claws to install the rear door inner glass weatherstrip.

Engage the claw to install the No. 1 door scuff plate clamp.

Connect each connector.

Engage the rear door trim board with the 4 clips of the rear door inner glass weatherstrip.

Engage the 7 clips to install the rear door trim board to the rear door panel.

Install the 3 screws.

Engage the 6 claws and install the door assist grip cover.

Engage the 3 claws to install the rear door inside handle bezel plug.

Install the rear seat reclining control cable.

Engage the 2 clips and claw and then install the reclining remote control lever sub-assembly.

Install the bolt.

Torque:

18 N*m{184 kgf*cm, 13 ft.*lbf}

Adjust the control lever to set the rear reclining adjuster assembly to its upper most position.

Pull plate A toward the front of the vehicle to lock the plate.

Install the rear door opening trim weatherstrip LH as shown in the illustration.

NOTICE:

After installation, check that the corners fit correctly.

Engage the 5 claws and 2 clips, then install the rear door scuff plate LH.

Install the rear door opening trim weatherstrip RH as shown in the illustration.

NOTICE:

After installation, check that the corners fit correctly.

Install the center seatback assembly with the 2 bolts.

Torque:

18 N*m{184 kgf*cm, 13 ft.*lbf}

Install the separate type rear seatback assembly LH with the 2bolts and 2 nuts.

Torque:

18 N*m{184 kgf*cm, 13 ft.*lbf}

Engage the 3 clamps and install the cover.

Install the 2 rear seat belts.

Install the separate type rear seatback assembly RH with the 2 bolts and 2 nuts.

Torque:

18 N*m{184 kgf*cm, 13 ft.*lbf}

Engage the 3 clamps and install the cover.

Install the rear seat belt.

Install the rear side seatback assembly with the bolt.

Torque:

18 N*m{184 kgf*cm, 13 ft.*lbf}

Install the separate type rear seatback assembly with the 2 bolts.

Torque:

18 N*m{184 kgf*cm, 13 ft.*lbf}

Install the separate type rear seat back assembly with the 2 bolts.

Torque:

18 N*m{184 kgf*cm, 13 ft.*lbf}

Attach the front hooks of the bench type rear seat cushion assembly to the vehicle body.

Confirm that the seat cushion is firmly installed.

NOTICE:

When installing the bench type rear seat cushion assembly, make sure that the seat belt buckle is not under the bench type rear seat cushion assembly.

Place the seat in the cabin.

Connect the connectors under the seat.

Connect the cable to the negative (-) battery terminal.

Move the front seat assembly fully forward by operating the slide and vertical power seat switch knob.

NOTICE:

Check that the seat is locked.

Temporarily install the front side of the front seat assembly with the 2 bolts.

Move the front seat assembly fully forward by operating the slide and vertical power seat switch knob.

NOTICE:

Check that the seat is locked.

Temporarily install the rear side of the front seat assembly with the 2 bolts.

Move the front seat assembly to the rearmost position by operating the slide and vertical power seat switch knob.

NOTICE:

Check that the seat is locked.

Fully tighten the 2 bolts on the front side of the front seat assembly in the order of the inner side bolt and then the outer side bolt.

Torque:

37 N*m{377 kgf*cm, 27 ft.*lbf}

Move the front seat assembly fully forward by operating the slide and vertical power seat switch knob.

NOTICE:

Check that the seat is locked.

Fully tighten the 2 bolts on the rear side of the front seat assembly in the order of the inner side bolt and then the outer side bolt.

Torque:

37 N*m{377 kgf*cm, 27 ft.*lbf}

Slide the inner seat track bracket cover along the seat rail toward the front of the vehicle. Engage claw A to the seat rail.

Push the inner seat track bracket cover to engage claw B.

Slide the seat track cover along the seat rail toward the front of the vehicle. Engage claw A to the seat rail.

Push the seat track cover to engage claw B.

Place the front seat assembly in the vehicle and align the adjuster pin with the hole on the vehicle side.

Connect the connector and clamp.

Move the front seat assembly to the rearmost position by operating the slide handle.

NOTICE:

Check that the seat is locked.

Temporarily install the front seat track bracket with the 2 bolts.

Move the front seat assembly fully forward by operating the slide handle.

NOTICE:

Check that the seat is locked.

Temporarily install the rear seat track bracket with the 2 bolts.

Move the front seat assembly to the rearmost position by operating the slide handle.

NOTICE:

Check that the seat is locked.

Fully tighten the 2 bolts on the front seat track bracket in the order of the inner side bolt and then the outer side bolt.

Torque:

37 N*m{377 kgf*cm, 27 ft.*lbf}

Move the front seat assembly fully forward by operating the slide handle.

NOTICE:

Check that the seat is locked.

Fully tighten the 2 bolts on the rear seat track bracket in the order of the inner side bolt and then the outer side bolt.

Torque:

37 N*m{377 kgf*cm, 27 ft.*lbf}

Slide the inner seat track bracket cover along the seat rail toward the front of the vehicle. Engage claw A to the seat rail.

Push the seat track bracket cover inner to engage claw B.

Slide the seat track cover along the seat rail toward the front of the vehicle. Engage claw A to the seat rail.

Push the seat track cover to engage claw B.

Inspect the SRS warning light (CAMRY_ACV40 RM000000XFD015X.html).

Check the power seat operation.

Check the seat heater operation (with seat heater system).

1. Turn the ignition switch on (IG).
   

2. Turn the seat heater switch ON.
   

3. Wait 5 minutes or more and confirm that the seat surface becomes warm.