Brake. Camry. Acv40 Gsv40
Brake Control. Camry. Acv40 Gsv40
Vehicle Stability Control System -- Problem Symptoms Table |
If there are no DTCs output and the problem still occurs, check the circuits for each problem symptom in the order given in the table below and proceed to the relevant troubleshooting page.
- HINT:
- Inspect the fuse and relay before investigating the suspected areas as shown in the table below.
- Inspect each malfunction circuit in numerical order for the corresponding symptom.
| Symptom | Suspected Area | See page |
| ABS, BA and/or EBD does not operate | 1. Check the DTC again and make sure that the normal system code is output. | CAMRY_ACV40 RM000000XHV02RX.html |
| 2. IG power source circuit | CAMRY_ACV40 RM000000XW602JX.html | |
| 3. Front speed sensor circuit | CAMRY_ACV40 RM000000XI9032X.html | |
| 4. Rear speed sensor circuit | CAMRY_ACV40 RM000000XIA031X.html | |
| 5. Check the brake actuator assembly with the intelligent tester. (Check brake actuator assembly operation using the Active Test function.) If abnormal, check the hydraulic circuit for leakage. | CAMRY_ACV40 RM0000013P9007X.html | |
| 6. If the symptoms still occur even after the above circuits in suspected areas have been inspected and proved to be normal, replace the brake actuator assembly (skid control ECU). | CAMRY_ACV40 RM0000013P6006X.html | |
| ABS, BA and/or EBD does not operate efficiently | 1. Check the DTC again and make sure that the normal system code is output. | CAMRY_ACV40 RM000000XHV02RX.html |
| 2. Front speed sensor circuit | CAMRY_ACV40 RM000000XI9032X.html | |
| 3. Rear speed sensor circuit | CAMRY_ACV40 RM000000XIA031X.html | |
| 4. Stop light switch circuit | CAMRY_ACV40 RM000000XIE02WX.html | |
| 5. Check the brake actuator assembly with the intelligent tester. (Check brake actuator assembly operation using the Active Test function.) If abnormal, check the hydraulic circuit for leakage. | CAMRY_ACV40 RM0000013P9007X.html | |
| 6. If the symptoms still occur even after the above circuits in suspected areas have been inspected and proved to be normal, replace the brake actuator assembly (skid control ECU). | CAMRY_ACV40 RM0000013P6006X.html | |
| ABS sensor DTC check cannot be done | 1. Check the DTC again and make sure that the normal system code is output. | CAMRY_ACV40 RM000000XHV02RX.html |
| 2. TC and CG terminal circuit | CAMRY_ACV40 RM000000XIU031X.html | |
| 3. If the symptoms still occur even after the above circuit in suspected areas has been inspected and proved to be normal, replace the brake actuator assembly (skid control ECU). | CAMRY_ACV40 RM0000013P6006X.html | |
| ABS warning light abnormal (Remains on) | 1. ABS warning light circuit | CAMRY_ACV40 RM000000XIH031X.html |
| 2. Brake actuator assembly (Skid control ECU) | CAMRY_ACV40 RM0000013P6006X.html | |
| ABS warning light abnormal (Does not come on) | 1. ABS warning light circuit | CAMRY_ACV40 RM000000XIQ02ZX.html |
| 2. Brake actuator assembly (Skid control ECU) | CAMRY_ACV40 RM0000013P6006X.html | |
| BRAKE warning light abnormal (Remains on) | 1. BRAKE warning light circuit | CAMRY_ACV40 RM000000YHG02ZX.html |
| 2. Brake actuator assembly (Skid control ECU) | CAMRY_ACV40 RM0000013P6006X.html | |
| BRAKE warning light abnormal (Does not come on) | 1. BRAKE warning light circuit | CAMRY_ACV40 RM000000YHH02YX.html |
| 2. Brake actuator assembly (Skid control ECU) | CAMRY_ACV40 RM0000013P6006X.html | |
| VSC and/or TRC does not operate | 1. Check the DTC again and make sure that the normal system code is output. | CAMRY_ACV40 RM000000XHV02RX.html |
| 2. IG power source circuit | CAMRY_ACV40 RM000000XW602JX.html | |
| 3. Check the hydraulic circuit for leakage | - | |
| 4. Front speed sensor circuit | CAMRY_ACV40 RM000000XI9032X.html | |
| 5. Rear speed sensor circuit | CAMRY_ACV40 RM000000XIA031X.html | |
| 6. Yaw rate and acceleration sensor circuit | CAMRY_ACV40 RM000001RFV01FX.html | |
| 7. Steering angle sensor circuit | CAMRY_ACV40 RM000000XIM02HX.html | |
| 8. If the symptoms still occur even after the above circuits in suspected areas have been inspected and proved to be normal, replace the brake actuator assembly (skid control ECU). | CAMRY_ACV40 RM0000013P6006X.html | |
| VSC sensor DTC check cannot be done | 1. Check the DTC again and make sure that the normal system code is output. | CAMRY_ACV40 RM000000XHV02RX.html |
| 2. TC and CG terminal circuit | CAMRY_ACV40 RM000000XIU031X.html | |
| 3. If the symptoms still occur even after the above circuit in suspected areas has been inspected and proved to be normal, replace the brake actuator assembly (skid control ECU). | CAMRY_ACV40 RM0000013P6006X.html | |
| SLIP indicator light abnormal (Remains on) | 1. SLIP indicator light circuit | CAMRY_ACV40 RM000000YHI02MX.html |
| 2. Brake actuator assembly (Skid control ECU) | CAMRY_ACV40 RM0000013P6006X.html | |
| SLIP indicator light abnormal (Does not come on) | 1. SLIP indicator light circuit | CAMRY_ACV40 RM000000YHJ02MX.html |
| 2. Brake actuator assembly (Skid control ECU) | CAMRY_ACV40 RM0000013P6006X.html | |
| Multi information display abnormal (Remains on) | 1. VSC warning light circuit | CAMRY_ACV40 RM000000XIO026X.html |
| 2. Brake actuator assembly (Skid control ECU) | CAMRY_ACV40 RM0000013P6006X.html | |
| Multi information display abnormal (Does not come on) | 1. VSC warning light circuit | CAMRY_ACV40 RM000000XIT025X.html |
| 2. Brake actuator assembly (Skid control ECU) | CAMRY_ACV40 RM0000013P6006X.html | |
| Sensor check cannot be done | 1. TS and CG terminal circuit | CAMRY_ACV40 RM000000XIV035X.html |
| 2. Brake actuator assembly (Skid control ECU) | CAMRY_ACV40 RM0000013P6006X.html | |
| Skid control buzzer abnormal | 1. Skid control buzzer circuit | CAMRY_ACV40 RM000000XIS02MX.html |
| 2. Brake actuator assembly (Skid control ECU) | CAMRY_ACV40 RM0000013P6006X.html |