Entry And Start System How To Proceed With Troubleshooting

Engine. Camry. Acv40 Gsv40
2Gr-Fe Starting. Camry. Acv40 Gsv40

  1. VEHICLE BROUGHT TO WORKSHOP

  2. CUSTOMER PROBLEM ANALYSIS CHECK

  3. INSPECT BATTERY VOLTAGE

  4. INSPECT COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM*

  5. CHECK FOR DTC*

  6. INSPECT BASIC OPERATION

  7. PROBLEM SYMPTOMS TABLE

  8. OVERALL ANALYSIS AND TROUBLESHOOTING*

  9. REPAIR OR REPLACE

  10. CONFIRMATION TEST

Entry And Start System -- How To Proceed With Troubleshooting


HINT:
  1. Use the following procedures to troubleshoot the push-button start function.
  2. *: Use the intelligent tester.


1.VEHICLE BROUGHT TO WORKSHOP

    NEXT


    2.CUSTOMER PROBLEM ANALYSIS CHECK
      HINT:
      1. In troubleshooting, confirm that the problem symptoms have been accurately identified. Preconceptions should be discarded in order to make an accurate judgment. To clearly understand what the problem symptoms are, it is extremely important to ask the customer about the problem and the conditions at the time the malfunction occurred.
      2. Gather as much information as possible for reference. Past problems that seem unrelated may also help in some cases.
      1. The following 5 items are important points in the problem analysis:

        What
        		Vehicle model, system name
        When
        		Date, time, occurrence frequency
        Where
        		Road conditions
        Under what conditions?
        		Running conditions, driving conditions, weather conditions
        How did it happen?
        		Problem symptoms

    NEXT


    3.INSPECT BATTERY VOLTAGE
      Standard Voltage:
      11 to 14 V
      If the voltage is below 11 V, recharge or replace the battery before proceeding.

    NEXT


    4.INSPECT COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM*

    1. Use the intelligent tester to check if the CAN Communication System is functioning normally (for LHD: CAMRY_ACV40 RM000000WI605LX.html) (for RHD: CAMRY_ACV40 RM000000WI605KX.html).

      2. Result:
      Result
      		Proceed to
      CAN DTC is not output
      		A
      CAN DTC is output (for LHD)
      		B
      CAN DTC is output (for RHD)
      		C


    		B.
    GO TO CAN COMMUNICATION SYSTEM (CAMRY_ACV40 RM000000WIB05NX.html)

    		C.
    GO TO CAN COMMUNICATION SYSTEM (CAMRY_ACV40 RM000000WIB05SX.html)
    A


    5.CHECK FOR DTC*

    1. Check for DTCs and note any codes that are output (CAMRY_ACV40 RM000000YEH05QX.html).

    2. Clear the DTCs.

    3. Recheck for DTCs.

      4. Result:
      Result
      		Proceed to
      DTC does not reoccur
      		A
      DTC reoccurs
      		B


    		B.
    GO TO DIAGNOSTIC TROUBLE CODE CHART (CAMRY_ACV40 RM000000XIZ05SX.html)
    A


    6.INSPECT BASIC OPERATION

    1. Turn the engine switch on (START) and check that the engine starts normally. Make sure the brake pedal is depressed and the shift position is P at this time.

    2. Check that the engine switch mode can be changed by pushing the engine switch.

      HINT:
      Without depressing the brake pedal, push the engine switch repeatedly. Engine switch mode should turn from off to on (ACC) to on (IG) and back to off.
      With the brake pedal depressed, push the engine switch repeatedly. Engine switch mode should turn to ENGINE START from any status.
      OK:
      Engine can start normally.

    NEXT


    7.PROBLEM SYMPTOMS TABLE

      Result:

      Result
      		Proceed to
      Fault is not listed in the problem symptoms table
      		A
      Fault is listed in the problem symptoms table
      		B


    		B.
    Go to step 9
    A


    8.OVERALL ANALYSIS AND TROUBLESHOOTING*

    1. Terminals of ECU (CAMRY_ACV40 RM000000XI2058X.html)

    2. Data List/Active Test (CAMRY_ACV40 RM000000XI505PX.html)


    NEXT


    9.REPAIR OR REPLACE

      NEXT


      10.CONFIRMATION TEST

        NEXT

        END