Rear Seat Outer Belt Assembly Removal
Restraints. Toyota Rav4. Aca30, 33, 38 Gsa33 Zsa30, 35
Seat Belt. Toyota Rav4. Aca30, 33, 38 Gsa33 Zsa30, 35
DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
REMOVE REAR DOOR SCUFF PLATE LH (for Short Body)
REMOVE REAR DOOR SCUFF PLATE LH (for Long Body)
REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH
REMOVE PACKAGE TRAY TRIM POCKET SUB-ASSEMBLY
REMOVE TONNEAU COVER ASSEMBLY
REMOVE REAR FLOOR NO. 1 BOARD
REMOVE DECK BOARD ASSEMBLY
REMOVE REAR FLOOR NO. 2 BOARD
REMOVE REAR FLOOR NO. 3 BOARD
REMOVE JACK CARRIER ASSEMBLY (for Short Body)
REMOVE REAR NO. 1 FLOOR MAT SUPPORT SIDE PLATE (for Short Body)
REMOVE REAR NO. 1 FLOOR MAT SUPPORT SIDE PLATE (for Long Body)
REMOVE BACK DOOR WEATHERSTRIP
REMOVE REAR FLOOR FINISH PLATE (for Short Body)
REMOVE REAR FLOOR FINISH PLATE (for Long Body)
REMOVE RECLINING REMOTE CONTROL LEVER BEZEL LH
REMOVE CHILD RESTRAINT SEAT TETHER ANCHOR COVER (for Short Body)
REMOVE CHILD RESTRAINT SEAT TETHER ANCHOR BRACKET (for Short Body)
DISCONNECT REAR NO. 1 SEAT BELT ASSEMBLY OUTER RH
REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH (for Short Body)
REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH (for Long Body)
REMOVE INNER ROOF SIDE GARNISH ASSEMBLY LH (for Short Body)
REMOVE INNER ROOF SIDE GARNISH ASSEMBLY LH (for Long Body)
REMOVE REAR NO. 1 SEAT BELT ASSEMBLY OUTER LH
Rear Seat Outer Belt Assembly -- Removal |
- HINT:
- Use the same procedures for the RH side and LH side.
- The procedures listed below are for the LH side.
1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
- CAUTION:
- Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.
2. REMOVE REAR DOOR SCUFF PLATE LH (for Short Body) |
Using a screwdriver, detach the 8 claws and remove the scuff plate.
- HINT:
- Tape the screwdriver tip before use.
3. REMOVE REAR DOOR SCUFF PLATE LH (for Long Body) |
Using a screwdriver, detach the 9 claws.
- HINT:
- Tape the screwdriver tip before use.
Using a clip remover, detach the 2 clips and remove the garnish.
4. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH |
5. REMOVE PACKAGE TRAY TRIM POCKET SUB-ASSEMBLY |
6. REMOVE TONNEAU COVER ASSEMBLY |
7. REMOVE REAR FLOOR NO. 1 BOARD |
8. REMOVE DECK BOARD ASSEMBLY |
9. REMOVE REAR FLOOR NO. 2 BOARD |
10. REMOVE REAR FLOOR NO. 3 BOARD |
11. REMOVE JACK CARRIER ASSEMBLY (for Short Body) |
Using a clip remover, remove the 7 clips and remove the jack carrier.
12. REMOVE REAR NO. 1 FLOOR MAT SUPPORT SIDE PLATE (for Short Body) |
Remove the 4 screws.
Using a clip remover, detach the 7 clips and remove the plate.
13. REMOVE REAR NO. 1 FLOOR MAT SUPPORT SIDE PLATE (for Long Body) |
Remove the 4 screws.
Using a clip remover, detach the 7 clips and remove the plate.
14. REMOVE BACK DOOR WEATHERSTRIP |
15. REMOVE REAR FLOOR FINISH PLATE (for Short Body) |
Using a clip remover, detach the 6 clips and remove the finish plate.
16. REMOVE REAR FLOOR FINISH PLATE (for Long Body) |
Using a clip remover, detach the 6 clips.
Detach the 2 claws and remove the finish plate.
17. REMOVE RECLINING REMOTE CONTROL LEVER BEZEL LH |
18. REMOVE CHILD RESTRAINT SEAT TETHER ANCHOR COVER (for Short Body) |
19. REMOVE CHILD RESTRAINT SEAT TETHER ANCHOR BRACKET (for Short Body) |
20. DISCONNECT REAR NO. 1 SEAT BELT ASSEMBLY OUTER RH |
Remove the lap belt outer anchor cover.
Remove the bolt and disconnect the floor anchor.
21. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH (for Short Body) |
Disconnect the rear No. 1 seat belt's floor anchor.
Remove the anchor cover.
Remove the bolt and disconnect the floor anchor.
Remove the bolt and 2 screws.
Using a screwdriver, detach the 5 claws.
- HINT:
- Tape the screwdriver tip before use.
Using a clip remover, detach the 5 clips and remove the trim board.
Disconnect the power outlet socket connector.
Remove the belt hanger.
22. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH (for Long Body) |
Disconnect the rear No.1 seat outer belt's floor anchor.
Remove the anchor cover.
Remove the bolt and disconnect the floor anchor.
Remove the 2 screws and 2 bolts.
Using a screwdriver, detach the 5 claws.
- HINT:
- Tape the screwdriver tip before use.
Using a clip remover, detach the 4 clips and remove the trim board.
Disconnect the power outlet socket connector.
Remove the belt hanger.
23. REMOVE INNER ROOF SIDE GARNISH ASSEMBLY LH (for Short Body) |
Using a clip remover, detach the 7 clips and remove the garnish.
24. REMOVE INNER ROOF SIDE GARNISH ASSEMBLY LH (for Long Body) |
Using a clip remover, detach the 7 clips and remove the garnish.
25. REMOVE REAR NO. 1 SEAT BELT ASSEMBLY OUTER LH |
Remove the bolt and disconnect the seat belt's shoulder anchor.
Remove the 2 bolts and seat belt.