Dtc B1424/24 Solar Sensor Circuit (Driver Side)
DESCRIPTION
WIRING DIAGRAM
INSPECTION PROCEDURE
READ VALUE USING INTELLIGENT TESTER (SOLAR SENSOR D SIDE)
INSPECT SOLAR SENSOR
CHECK WIRE HARNESS (SOLAR SENSOR - AIR CONDITIONING AMPLIFIER)
DTC B1424/24 Solar Sensor Circuit (Driver Side) |
DESCRIPTION
The solar sensor, which is installed on the upper side of the instrument panel, detects sunlight and controls the air conditioning AUTO mode. The output voltage from the solar sensor varies in accordance with the amount of sunlight. When the sunlight increases, the output voltage increases. As the sunlight decreases, the output voltage decreases.The air conditioning amplifier detects changes in the output voltage from the solar sensor.DTC No.
| DTC Detection Condition
| Trouble Area
|
B1424/24
| Open or short in passenger side solar sensor circuit
| - Solar sensor
- Harness and connector between solar sensor and air conditioning amplifier
- Air conditioning amplifier
|
WIRING DIAGRAM
INSPECTION PROCEDURE
1.READ VALUE USING INTELLIGENT TESTER (SOLAR SENSOR D SIDE) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and turn the intelligent tester main switch ON.
Select the item below in the Data List, and read the value displayed on the intelligent tester.
- Air conditioning amplifier:
Item
| Measure Item / Display (Range)
| Normal Condition
| Diagnostic Note
|
Solar Sens-D
| Driver side solar sensor / Min.: 0, Max.: 255
| Driver side temperature increases as brightness increases
| -
|
- OK:
- The display is as specified in the normal condition column.
- Result::
Result
| Proceed to
|
NG
| A
|
OK (Checking from the PROBLEM SYMPTOMS TABLE)
| B
|
OK (Checking from the DTC)
| C
|
| PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE |
|
|
| REPLACE AIR CONDITIONING AMPLIFIER |
|
|
Remove the solar sensor.
Measure the resistance of the sensor.
Connect the positive (+) lead from the ohmmeter to terminal 1 and the negative (-) lead to terminal 3 of the solar sensor.
- Standard resistance:
Tester Connection
| Condition
| Specified Condition
|
1 (SS) - 3 (TSD)
| Sensor exposed to electric light
| Except ∞ Ω
|
1 (SS) - 3 (TSD)
| Sensor covered with cloth
| ∞ Ω (No continuity)
|
- NOTICE:
- The connection procedure for using a digital tester such as an electrical tester is shown above. When using an analog tester, connect the positive (+) lead to terminal 3 and the negative (-) lead to terminal 1 of the solar sensor.
- HINT:
- As the inspection light is moved away from the sensor, the voltage decreases.
- Use an incandescent light for the inspection. Position it about 30 cm (11.8 in.) from the solar sensor.
3.CHECK WIRE HARNESS (SOLAR SENSOR - AIR CONDITIONING AMPLIFIER) |
Disconnect the F1 sensor connector.
Disconnect the E41 amplifier connector.
Measure the resistance of the wire harness side connectors.
- Standard resistance:
Tester Connection
| Specified Condition
|
E41-33 (TSD) - F1-3 (TSD)
| Below 1 Ω
|
E41-31 (S5-4) - F1-1 (SS)
| Below 1 Ω
|
E41-33 (TSD) - Body ground
| 1 MΩ or higher
|
E41-31 (S5-4) - Body ground
| 1 MΩ or higher
|
| REPAIR OR REPLACE HARNESS AND CONNECTOR |
|
|
OK |
|
|
|
REPLACE AIR CONDITIONING AMPLIFIER |
|