Dtc P0741 Torque Converter Clutch Solenoid Performance (Shift Solenoid Valve Sl)

Transmission. Toyota Rav4. Aca30, 33, 38 Gsa33 Zsa30, 35
K111F Cvt. Toyota Rav4. Aca30, 33, 38 Gsa33 Zsa30, 35

DESCRIPTION

MONITOR DESCRIPTION

INSPECTION PROCEDURE

CHECK DTC OUTPUT (IN ADDITION TO DTC P0741 AND P2757)

CLEAR DTC

PERFORM DRIVE TEST

REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY

REPLACE TORQUE CONVERTER ASSEMBLY

PERFORM INITIALIZATION

DTC P0741 Torque Converter Clutch Solenoid Performance (Shift Solenoid Valve SL)

DTC P2757 Torque Converter Clutch Pressure Control Solenoid Control Circuit Performance (Shift Solenoid Valve DSU)


DESCRIPTION

The ECM uses shift solenoid valves SL and DSU to perform lock-up control in response to the driving conditions.
NOTICE:
If any parts inside the torque converter assembly are damaged, DTC P0741/64 and P2757/64 could be output. In this case, make sure to replace both the torque converter assembly and the continuously variable transaxle assembly as broken pieces may have entered through the oil passages and some of them may be present in the continuously variable transaxle assembly.
HINT:
Shift solenoid valve DSU controls the lock-up clutch pressure in response to the input torque.

DTC Code
DTC Detection Condition
  1. Diagnosis Condition
  2. Malfunction Status
  3. Malfunction Time
  4. Other
Trouble Area
P0741
  1. The engine is warmed up, and the vehicle is driven at a speed of 10 km/h (6.2 mph) or more with the shift lever in D.
  2. The lock-up signal is on, but lock-up is off.
  3. -
  4. 2 trip detection logic
  1. Continuously variable transaxle assembly
  2. torque converter assembly
P2757
  1. The engine is warmed up, and the vehicle is driven at a speed of 10 km/h (6.2 mph) or more with the shift lever in D.
  2. The lock-up signal is on, but lock-up is off.
  3. -
  4. 2 trip detection logic
  1. The engine is warmed up, and the vehicle is driven at a speed of 10 km/h (6.2 mph) or more with the shift lever in D.
  2. The lock-up signal is off, but lock-up is on.
  3. -
  4. 2 trip detection logic

MONITOR DESCRIPTION

When performing lock-up control (on/off) of the torque converter, the ECM compares the rotating speeds of the turbine (NT) and engine (NE) to detect mechanical malfunctions in the shift solenoid valves SL and DSU. When the rotating speeds are different than expected, the ECM detects the problem, illuminates the MIL and stores the DTC.

INSPECTION PROCEDURE

1.CHECK DTC OUTPUT (IN ADDITION TO DTC P0741 AND P2757)

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs using the tester.

    Result
    Result
    		Proceed to
    Only P0741 and/or P2757 is output
    		A
    P0741 and/or P2757 and other DTCs are output
    		B
    HINT:
    If any other DTCs besides P0741 or P2757 are output, perform troubleshooting for those DTCs first.


B
GO TO DTC CHART (RAV4_ACA30 RM0000030G9017X.html)
A


2.CLEAR DTC

  1. Clear the DTC (RAV4_ACA30 RM000000W770CCX.html).


NEXT


3.PERFORM DRIVE TEST
CAUTION:
Strictly observe posted speed limits, traffic laws and road conditions when performing the road test.
NOTICE:
  1. This test must be conducted after checking and confirming that the engine is operating normally.
  2. Perform this test while the CVT fluid temperature is between 50 and 100°C (122 and 212°F).
  3. Perform the test with the A/C off and no electrical load.

  4. Toyota Rav4. Aca30, 33, 38 Gsa33 Zsa30, 35.K111F Cvt.Continuously Variable Transaxle System. Dtc P0741 Torque Converter Clutch Solenoid Performance (Shift Solenoid Valve Sl)
    Make sure to replace both the torque converter assembly and the continuously variable transaxle assembly if any parts inside the torque converter assembly are damaged. Broken pieces may have entered through the oil passages and some of them may be present in the continuously variable transaxle assembly.
Text in Illustration
*1
Oil seal
*a
Example of the damage
*b
Damage
HINT:
  1. Lock-up control will not operate when the CVT fluid temperature is 40°C (104°F) or less and the vehicle speed is 60 km/h (37 mph) or less, or when the CVT fluid temperature is 5°C (41°F) or less.
  2. Lock-up control will not operate when the engine coolant temperature is 30°C (86°F) or less.
  3. The lock-up off vehicle speed may vary depending on the electrical load, air conditioning and brake operations.

  1. Connect the intelligent tester to the DLC3.

  1. Start the engine.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / SPD (NT), Lock Up and Engine Speed.

  1. Check the Data List while driving.

    Result
    Result
    		Proceed to
    When the lock-up is on, the turbine speed is lower than the engine speed.
    		A
    When the lock-up is off, the turbine speed is equal to the engine speed.
    When the lock-up is on, the turbine speed is equal to the engine speed.
    		B
    When the lock-up is off, the turbine speed is lower than the engine speed.


B
Go to step 4
A


4.REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY

  1. Replace the continuously variable transaxle assembly (RAV4_ACA30 RM00000192D01ZX.html).


NEXT


5.REPLACE TORQUE CONVERTER ASSEMBLY
(RAV4_ACA30 RM00000192D01ZX.html)

NEXT


6.PERFORM INITIALIZATION
NOTICE:
  1. Performing reset memory will clear the learned values of both the yaw rate sensor assembly*1 or deceleration sensor*2 (deceleration sensor 0 point calibration) and CVT oil pressure (CVT oil pressure calibration). Make sure to perform reset memory, yaw rate sensor assembly*1 or deceleration sensor*2 0 point calibration and CVT oil pressure calibration when replacing any of the parts shown in the following table:
    Replaced Part
    1. Continuously variable transaxle assembly
    2. ECM
    3. Oil pressure sensor
    4. Yaw rate sensor assembly (w/ VSC)
    5. Deceleration sensor (w/o VSC)
    6. Brake actuator assembly (skid control ECU)
  2. After performing reset memory, always perform yaw rate sensor assembly*1 or deceleration sensor*2 (deceleration sensor 0 point) calibration first, and then CVT oil pressure calibration.
  3. Always perform 0 point calibration with the vehicle on level ground.
  4. Do not shake or vibrate the vehicle during 0 point calibration.

  1. Using the intelligent tester, perform reset memory, deceleration sensor 0 point calibration and CVT oil pressure calibration (RAV4_ACA30 RM000003UQR002X.html).

  1. Check that no DTC is stored.


NEXT

END