Entry And Start System Data List / Active Test

Engine. Toyota Rav4. Aca30, 33, 38 Gsa33 Zsa30, 35
1Az-Fe Starting. Toyota Rav4. Aca30, 33, 38 Gsa33 Zsa30, 35

  1. READ DATA LIST

  1. PERFORM ACTIVE TEST

Entry And Start System -- Data List / Active Test



READ DATA LIST
HINT:
Using the intelligent tester's Data List allows switch, sensor, actuator and other item values to be read without removing any parts. Reading the Data List early in troubleshooting is one way to save time.
NOTICE:
In the table below, the values listed under Normal Condition are for reference only. Do not depend solely on these values when determining whether or not a part is faulty.

  1. Turn the engine switch off.

  2. Connect the intelligent tester to the DLC3.

  3. Turn the engine switch on (IG) and turn the tester ON.

  4. Select the following menu items: Body / (desired system) / Data List.

  5. Check the values by referring to the table below.

    Main Body
    Tester Display
    		Measurement Item/Range
    		Normal Condition
    		Diagnostic Note
    ACC SW
    		Engine switch on (ACC)/ON or OFF
    		ON: Engine switch on (ACC)
    OFF: Engine switch off
    		-
    IG SW
    		Engine switch on (IG)/ON or OFF
    		ON: Engine switch on (IG)
    OFF: Engine switch off
    		-
    Stop Light SW
    		Stop light switch/ON or OFF
    		ON: Brake pedal depressed
    OFF: Brake pedal released
    		-
    Start Switch1
    		Start switch 1/ON or OFF
    		ON: Engine switch on (IG)
    OFF: Engine switch off
    		-
    Start Switch2
    		Start switch 2/ON or OFF
    		ON: Engine switch on (IG)
    OFF: Engine switch off
    		-
    Steering Unlock Switch
    		Steering lock condition/ON or OFF
    		ON: Steering unlocked
    OFF: Steering locked
    		-
    Neutral SW/ Clutch SW
    		Park/neutral position switch (except M/T) or clutch start switch (for M/T) signal/ON or OFF
    		ON: Brake pedal (except M/T) or clutch pedal (for M/T) depressed and shift lever in P or N (except M/T)
    ON: Brake pedal (except M/T) or clutch pedal (for M/T) released and shift lever not in P or N (except M/T)
    		-
    Shift P Signal (except M/T)
    		Shift lever P position signal/ON or OFF
    		ON: Shift lever in P
    OFF: Shift lever not in P
    		-
    Vehicle Speed Signal
    		Vehicle speed signal/Stop or Run
    		Stop: Vehicle stopped
    Run: Vehicle being driven
    		-
    Engine Condition
    		Engine condition/Stop or Run
    		Stop: Engine stopped
    Run: Engine running
    		-
    IG1 Relay Monitor(Outside)
    		IG1 relay outer relay monitor/ON or OFF
    		ON: Engine switch on (IG)
    OFF: Engine switch off
    		-
    IG2 Relay Monitor(Outside)
    		IG2 relay outer relay monitor/ON or OFF
    		ON: Engine switch on (IG)
    OFF: Engine switch off
    		-
    IG1 Relay Monitor(Inside)
    		IG1 relay inner relay monitor/ON or OFF
    		ON: Engine switch on (IG)
    OFF: Engine switch off
    		-
    IG2 Relay Monitor(Inside)
    		IG2 relay inner relay monitor/ON or OFF
    		ON: Engine switch on (IG)
    OFF: Engine switch off
    		-
    ACC Relay Monitor
    		ACC relay monitor/ON or OFF
    		ON: Engine switch on (ACC)
    OFF: Engine switch off
    		-
    Latch Circuit
    		Latch circuit/ON or OFF
    		ON: Engine switch on (IG)
    OFF: Engine switch off or on (ACC)
    		-
    Starter Request Signal
    		Starter request signal/ON or OFF
    		ON: ST relay on
    OFF: ST relay off
    		-
    Power Supply Condition
    		Power supply condition/ALL OFF, ACC ON, IG2 ON or ST ON
    		ALL OFF: All relays off
    ACC ON: ACC relay on
    IG2 ON: IG2 relay on
    ST ON: STSW signal on
    		-
    ACC Relay Cut Signal
    		ACC relay cut signal/ON or OFF
    		ON: Engine cranking
    OFF: Engine not cranking
    		-
    Starter Relay Monitor
    		ST relay monitor/ON or OFF
    		ON: Engine cranking
    OFF: Engine not cranking
    		-
    Communication Entry&Start/Wireless
    		Communication to certification ECU/OK or STOP
    		OK: Communication
    STOP: No communication
    		-
    The Number of DTC
    		Number of diagnostic trouble codes/Min: 0, Max: 255
    		-
    		-

    Entry&Start
    Tester Display
    		Measurement Item/Range
    		Normal Condition
    		Diagnostic Note
    Ignition Switch
    		Engine switch/ON or OFF
    		ON: Engine switch on (IG)
    OFF: Engine switch off
    		-
    Unmatched Vehicle-ID
    		Key ID/Yes or No
    		Yes: Key ID matches
    No: Key ID differs
    		-
    No Response
    		Response/Yes or No
    		Yes: Response
    No: No response
    		-
    Unmatch Code or Form
    		Code format/Yes or No
    		Yes: Code format matches
    No: Code format differs
    		-
    Key Low Battery
    		Key battery conditions/On or Off
    		On: Battery depleted
    Off: Battery not depleted
    		-
    #Codes
    		Number of diagnostic trouble codes/Min: 0, Max: 255
    		-
    		-
    ID Code Difference(Resp)
    		ID code/Yes or No
    		Yes: ID code matches
    No: ID code differs
    		-
    C Code Difference
    		Challenge code/Yes or No
    		Yes: Challenge code matches
    No: Challenge code differs
    		-
    Engine Start Condition
    		Engine start permission determined by certification ECU/OK or NG
    		OK: Engine start permitted
    NG: Engine start prohibited
    		-
    S Code Check
    		S code certification result/NG or OK
    		OK: S code certification result normal
    NG: S code certification result abnormal
    		-
    L Code Check
    		L code certification result/NG or OK
    		OK: L code certification result normal
    NG: L code certification result abnormal
    		-
    Ignition Available Area
    		Key area where engine start is possible/All or Front
    		All: All areas
    Front: Front only
    		-


PERFORM ACTIVE TEST
HINT:
Performing the Active Test enables components including the relays, VSV (Vacuum Switching Valve), and actuators, to be operated without removing any parts. The Active Test can be performed with an intelligent tester. Performing the Active Test as the first step of troubleshooting is one method of shortening diagnostic time. The Data List can be displayed during the Active Test.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the engine switch on (IG).

  3. Turn the tester ON.

  4. Select the following menu items: Body / (desired system) / Active Test.

  5. Perform the Active Test by referring to the table below.

    Main Body
    Tester Display
    		Test Part
    		Control Range
    		Diagnostic Note
    Indicator for Lighting
    		Indicator illumination
    		ON/OFF
    		-
    Indicator Condition
    		Indicator light illumination pattern
    		Green/Red/No Sig
    		-
    P Supply for Steering Lock
    		Steering lock ECU power supply
    		ON/OFF
    		-

    Entry&Start
    Tester Display
    		Test Part
    		Control Range
    		Diagnostic Note
    Fr-Seat Inside Transmitter
    		Indoor key oscillator (for front floor)
    		ON/OFF
    		-