Front Bumper -- Installation |
- HINT:
- A bolt without a torque specification is shown in the standard bolt chart (LandCruiser RM00000118W0G8X.html).
| 1. INSTALL FRONT BUMPER BRACKET SUB-ASSEMBLY LH |
Install the front bumper bracket sub-assembly LH with the 2 bolts.
- Torque:
- 8.0 N*m{82 kgf*cm, 71 in.*lbf}
| 2. INSTALL FRONT BUMPER BRACKET SUB-ASSEMBLY RH |
- HINT:
- Use the same procedure described for the LH side.
| 3. INSTALL HEADLIGHT ASSEMBLY LH |
for Halogen Headlight:
(LandCruiser RM000003QVJ01CX_01_0001.html)
for LED Headlight:
(LandCruiser RM000003QVJ01DX_01_0001.html)
| 4. INSTALL HEADLIGHT ASSEMBLY RH |
- HINT:
- Use the same procedure described for the LH side.
| 5. INSTALL FRONT BUMPER CENTER UPPER RETAINER |
Install the front bumper center upper retainer with the 3 bolts.
- Torque:
- 8.0 N*m{82 kgf*cm, 71 in.*lbf}
| 6. INSTALL FRONT BUMPER SIDE SUPPORT LH |
Attach the 2 claws to install the front bumper side support LH.
Install the screw and bolt.
- Torque:
- for screw:
- 3.0 N*m{31 kgf*cm, 27 in.*lbf}
| 7. INSTALL FRONT BUMPER SIDE SUPPORT RH |
- HINT:
- Use the same procedure described for the LH side.
| 8. INSTALL FRONT BUMPER NO. 2 EXTENSION SUB-ASSEMBLY LH |
Install the front bumper No. 2 extension sub-assembly LH with the 4 bolts.
- Torque:
- 65 N*m{663 kgf*cm, 48 ft.*lbf}
| 9. INSTALL FRONT BUMPER NO. 2 EXTENSION SUB-ASSEMBLY RH |
- HINT:
- Use the same procedure described for the LH side.
| 10. INSTALL FRONT BUMPER REINFORCEMENT SUB-ASSEMBLY |
Install the front bumper reinforcement sub-assembly with the 6 nuts.
- Torque:
- 30 N*m{306 kgf*cm, 22 ft.*lbf}
| 11. INSTALL FRONT BUMPER LOWER COVER |
Install the front bumper lower cover with the 5 bolts.
- Torque:
- 8.0 N*m{82 kgf*cm, 71 in.*lbf}
Install the clip.
| 12. INSTALL FRONT BUMPER ENERGY ABSORBER |
Install the front bumper energy absorber.
| 13. INSTALL FRONT BUMPER COVER |
w/ TOYOTA Parking Assist-sensor System, w/ Fog Light:
Connect the 3 connectors.
w/ TOYOTA Parking Assist-sensor System, w/o Fog Light:
Connect the connector.
w/o TOYOTA Parking Assist-sensor System, w/ Fog Light:
Connect the 2 connectors.
w/ Headlight Cleaner System:
Connect the No. 1 headlight cleaner hose.
Attach the 16 claws to install the front bumper cover.
- NOTICE:
- Do not hold the middle of the front bumper cover, as it may become reformed.
Install the 4 clips.
Install the 2 bolts labeled A and 2 bolts labeled B.
- Torque:
- bolt B:
- 8.0 N*m{82 kgf*cm, 71 in.*lbf}
Text in Illustration *1 Screw *2 Bolt A *3 Bolt B
 |
Install the 2 screws.
Install the 2 screws.
- HINT:
- Use the same procedure for the screws on the other side.
| 14. INSTALL RADIATOR GRILLE |
Attach the 8 claws to install the radiator grille.
Install the 4 screws.
| 15. INSTALL UPPER RADIATOR SUPPORT SEAL |
Install the upper radiator support seal with the 13 clips.
| 16. ADJUST FOG LIGHT AIMING (w/ Fog Light) |
 |
Adjust the aim vertically.
Adjust the aim of each fog light to the specified range by turning the aiming screw with a screwdriver.Text in Illustration *1 Aiming Screw - NOTICE:
- The final turn of the aiming screw should be made in the clockwise direction. If the screw is tightened excessively, loosen it, and then retighten it so that the final turn of the screw is in the clockwise direction.
- HINT:
- If it is not possible to correctly adjust fog light aim, check the bulb, fog light unit and fog light unit reflector installation.
| 17. CHECK TOYOTA PARKING ASSIST-SENSOR SYSTEM (w/ TOYOTA Parking Assist-sensor System) |
w/ Multi-display:
(LandCruiser RM000000VVD08FX.html)
w/o Multi-display:
(LandCruiser RM000003QOH010X.html)