Power Window Regulator Motor (For Front Door) -- Installation |
- HINT:
- Use the same procedure for the RH and LH sides.
- The procedure listed below is for the LH side.
- A bolt without a torque specification is shown in the standard bolt chart (LandCruiser RM00000118W0G8X.html).
| 1. INSTALL FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH |
- NOTICE:
- The regulator arm must be below the intermediate position when installing the power window regulator motor.
Apply MP grease to the sliding and rotating areas of the regulator motor.
 |
Using a T25 "TORX" socket wrench, install the power window regulator motor with the 3 screws.
- Torque:
- 5.4 N*m{55 kgf*cm, 48 in.*lbf}
- HINT:
- A new front window regulator uses self-tapping screws to thread new installation holes when the self-tapping screws are inserted.
| 2. INSTALL FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY LH |
Apply MP grease to the sliding parts of the front door window regulator assembly.
Install the temporary bolt to the front door window regulator assembly.
Temporarily install the front door window regulator assembly with the temporary bolt.
Text in Illustration *1 Temporary Bolt
 |
Temporarily install the 5 bolts, and then tighten the temporary bolt and 5 bolts.
- Torque:
- 8.0 N*m{82 kgf*cm, 71 in.*lbf}
- HINT:
- Tighten the bolts in the order shown in the illustration.
Connect the connector.
| 3. INSTALL FRONT DOOR GLASS SUB-ASSEMBLY LH |
Connect the cable to the negative (-) battery terminal.
Connect the power window regulator master switch assembly and move the front door glass sub-assembly so that the door glass bolt installation locations can be seen.
Disconnect the cable from the negative (-) battery terminal and power window regulator master switch assembly.
- CAUTION:
- Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system (LandCruiser RM000003YMF011X.html).
Insert the front door glass sub-assembly into the front door panel along the front door glass run as indicated by the arrows in the order shown in the illustration.
 |
Install the front door glass sub-assembly with the 2 bolts.
- Torque:
- 5.5 N*m{56 kgf*cm, 49 in.*lbf}
- HINT:
- Tighten the bolts in the order shown in the illustration.
 |
| 4. INSTALL FRONT DOOR SERVICE HOLE COVER LH |
Apply new butyl tape to the front door panel.
Pass the front door lock remote control cable assembly and front door inside locking cable assembly through a new front door service hole cover.
Text in Illustration *1 Reference Point
 |
Attach the front door service hole cover using the reference points on the front door panel.
- NOTICE:
- There should be no wrinkles or folds after attaching the service hole cover.
- After attaching the service hole cover, check the seal quality.
- NOTICE:
- Securely install the front door service hole cover preventing wrinkles and air bubbles.
Attach the 2 clamps.
 |
Install the bolt to the front door wire.
| 5. INSTALL FRONT NO. 1 SPEAKER ASSEMBLY |
Temporarily install the speaker by attaching the 2 claws of the speaker to the door panel.
Install the speaker with the 4 screws in the order shown in the illustration.
 |
Connect the speaker connector.
- NOTICE:
- Do not touch the cone of the speaker.
| 6. INSTALL FRONT DOOR INNER GLASS WEATHERSTRIP LH |
Install the front door inner glass weatherstrip.
 |
| 7. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH |
Connect the front door lock remote control cable assembly and front door inside locking cable assembly.
 |
Connect 2 connectors.
w/ Seat Position Memory System:
Connect the connectors.
Attach the front door trim board sub-assembly by attaching the 4 claws of the front door inner glass weatherstrip as shown in the illustration.
 |
Attach the 12 clips and front door trim board retainer to install the front door trim board sub-assembly.
 |
Install the 3 screws.
| 8. INSTALL ASSIST GRIP COVER LH |
Attach the 8 claws to install the assist grip cover.
 |
| 9. INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH LH |
Attach the 2 claws to install the front door lower frame bracket garnish.
| 10. INSTALL NO. 2 DOOR INSIDE HANDLE BEZEL LH |
Attach the 3 claws to install the inside handle bezel.
 |
| 11. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
- NOTICE:
- When disconnecting the cable, some systems need to be initialized after the cable is reconnected (LandCruiser RM000003YMF011X.html).
| 12. INITIALIZE POWER WINDOW CONTROL SYSTEM |
Initialize the power window control system (LandCruiser RM0000011V20BLX.html).