INSTALL FRONT SEAT SIDE AIRBAG ASSEMBLY (w/ Front Seat Side Airbag)
INSTALL FRONT SEATBACK HEATER ASSEMBLY RH (w/ Seat Heater System)
INSTALL SEAT HEATER CONTROL SUB-ASSEMBLY RH (w/ Seat Heater System)
INSTALL FRONT SEAT CUSHION HEATER ASSEMBLY RH (w/ Seat Heater System)
Front Seat Assembly (For Walk In Seat Type) -- Reassembly |
- CAUTION:
- Wear protective gloves. Sharp areas on the parts may injure your hands.
- HINT:
- Use the same procedure for RHD and LHD vehicles.
- The procedure listed below is for LHD vehicles.
- Use the same procedure for the RH and LH sides.
- The procedure listed below is for the RH side.
| 1. INSTALL FRONT SEAT SIDE AIRBAG ASSEMBLY (w/ Front Seat Side Airbag) |
- CAUTION:
- The nuts must not be reused.
- Make sure that the separate type front seatback spring assembly is not deformed. If it is, replace it with a new one.
- HINT:
- Use the same procedure for the RH and LH sides.
Install the front seat side airbag assembly with 2 new nuts.
- Torque:
- 5.5 N*m{56 kgf*cm, 49 in.*lbf}
Attach the 2 clamps.
| 2. INSTALL FRONT SEAT LOWER CUSHION SHIELD RH |
Install the cushion shield with the screw.
| 3. INSTALL FRONT SEAT CUSHION COVER RH |
Install the cover with the screw.
| 4. INSTALL SEPARATE TYPE FRONT SEATBACK PAD |
Install the seatback pad.
| 5. INSTALL FRONT SEATBACK HEATER ASSEMBLY RH (w/ Seat Heater System) |
 |
Set the seatback heater with the name stamp side facing the seatback cover.
Text in Illustration *1 Tack Pin *2 Seatback Cover *3 Seatback Heater *4 Name Stamp
Install the seatback heater with new tack pins.
| 6. INSTALL SEPARATE TYPE FRONT SEATBACK COVER |
Using hog ring pliers, install the seatback cover to the seatback pad with new hog rings.
- NOTICE:
- Be careful not to damage the cover.
- When installing the hog rings, avoid wrinkling the cover.
- HINT:
- The number of hog rings differs according to seat type.
Text in Illustration *A for Type A *B for Type B *1 Hog Ring Pliers - -
Attach the 4 claws to install the 2 headrest supports.
w/ Front Seat Side Airbag:
Connect the seatback cover bracket to the seatback pad.
Install the seatback cover bracket to the seat frame with the nut.
- Torque:
- 5.5 N*m{56 kgf*cm, 49 in.*lbf}
- NOTICE:
- After the seatback trim cover is assembled, make sure the side airbag strap is not twisted.
 |
Close the 2 fasteners, and then close the seatback cover.
Text in Illustration *A for Cloth Seat *B for Leather Seat
Using hog ring pliers, install 3 new hog rings.
Text in Illustration *1 Hog Ring Pliers
 |
| 7. INSTALL RECLINING ADJUSTER INSIDE COVER LH |
 |
Move the cover in the direction of the arrow to install the cover.
Attach the guide.
| 8. INSTALL RECLINING ADJUSTER INSIDE COVER RH |
- HINT:
- Use the same procedure described for the LH side.
| 9. INSTALL FRONT SEAT WIRE RH |
Install the seat wire.
| 10. INSTALL SEAT HEATER CONTROL SUB-ASSEMBLY RH (w/ Seat Heater System) |
Attach the 2 clamps to install the seat heater control.
Connect the connector.
| 11. INSTALL FRONT SEAT CUSHION EDGE PROTECTOR LH |
 |
Move the protector in the direction of the arrow to attach the hook and 2 guides and install the protector.
Text in Illustration *1 Hook *2 Guide
Install the screw.
| 12. INSTALL FRONT SEAT CUSHION EDGE PROTECTOR RH |
 |
Move the protector in the direction of the arrow to attach the hook and guide and install the protector.
Text in Illustration *1 Hook *2 Guide
Attach the clip.
Install the screw.
| 13. INSTALL FRONT SEAT CUSHION HEATER ASSEMBLY RH (w/ Seat Heater System) |
 |
Set the seat cushion heater with the name stamp side facing the seat cushion cover.
Text in Illustration *1 Tack Pin *2 Seatback Cover *3 Seatback Heater *4 Name Stamp
Install the seat cushion heater with new tack pins.
| 14. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER |
 |
Using hog ring pliers, install the seat cushion cover to the seat cushion pad with new hog rings.
Text in Illustration *1 Hog Ring Pliers - NOTICE:
- Be careful not to damage the cover.
- When installing the hog rings, avoid wrinkling the cover.
| 15. INSTALL SEAT CUSHION COVER WITH PAD |
Install the seat cushion cover with pad.
Attach the claw to connect the connector.
Install the clip.
w/ Seat Heater System:
Connect the seat heater connector and attach the 3 wire harness clamps.
| 16. INSTALL CAP |
Install the 2 caps.
| 17. INSTALL SEPARATE TYPE FRONT SEATBACK ASSEMBLY |
Install the seatback assembly with the 4 bolts.
- Torque:
- 42 N*m{428 kgf*cm, 31 ft.*lbf}
Attach the hook.
Attach the cable clamp to connect the cable.
w/ Front Seat Side Airbag:
Connect the airbag wire harness.
Attach the fastening tape to close the cover.
Attach the 3 airbag wire harness clamps.
Attach the claw and connect the airbag connector.
w/ Seat Heater System:
Connect the seat heater connector and attach the wire harness clamp.
Install the rubber band to the seat cushion spring.
| 18. INSTALL FRONT SEAT INNER BELT ASSEMBLY RH |
Install the front seat belt anchor plate.
Install the front seat inner belt assembly RH to the front seat assembly RH with the nut.
- Torque:
- 42 N*m{428 kgf*cm, 31 ft.*lbf}
- NOTICE:
- Do not allow the anchor part of the front seat inner belt assembly RH to overlap the protruding parts of the front seat adjuster.
for Manual Seat, Power Seat 4 Way Seat Type:
Connect the 2 connectors and attach the 3 clamps.
for Power Seat 8 Way Seat Type:
Connect the 2 connectors and attach the 6 clamps.
| 19. INSTALL FRONT SEAT INNER CUSHION SHIELD RH |
Attach the 5 claws to install the cushion shield.
| 20. INSTALL FRONT SEAT CUSHION SHIELD RH |
Attach the cable clamp.
Attach the 2 clips and 5 claws to install the cushion shield.
Install the screw.
| 21. INSTALL RECLINING ADJUSTER RELEASE HANDLE RH |
 |
Attach the claw to install the handle.