Dtc B2653 Lifter Sensor Malfunction


DESCRIPTION

WIRING DIAGRAM

INSPECTION PROCEDURE

PERFORM ACTIVE TEST USING INTELLIGENT TESTER (POWER SEAT MOTOR FUNCTION)

CHECK FRONT POWER SEAT SWITCH (LIFTER MOTOR CIRCUIT)

CHECK SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY (LIFTER MOTOR)

CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH - LIFTER MOTOR)

INSPECT SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY (LIFTER MOTOR)

CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH - LIFTER MOTOR)

DTC B2653 Lifter Sensor Malfunction


DESCRIPTION

When the front power seat switch does not receive a sensor signal despite upward or downward movement of the seat by power seat motor operation, this DTC is stored.

DTC Code
DTC Detection Condition
Trouble Area
B2653
The upward and downward lock detection position of the sensor is the same.
  1. Front power seat switch
  2. Separate type front seat cushion spring assembly (Lifter motor)
  3. Harness or connector

WIRING DIAGRAM


Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155.Seat.Front Power Seat Control System (W/ Memory). Dtc B2653 Lifter Sensor Malfunction


INSPECTION PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (POWER SEAT MOTOR FUNCTION)

  1. Select the Active Test, use the intelligent tester to generate a control command, and then check the power seat motor function (LandCruiser RM0000039RN030X.html).

    Tester Display
    		Test Part
    		Control Range
    		Diagnostic Note
    Lifter Operation
    		Seat lifter operation
    		Up / OFF / Down
    		-
    OK:
    Motor operates normally.


NG
Go to step 5
OK


2.CHECK FRONT POWER SEAT SWITCH (LIFTER MOTOR CIRCUIT)


    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155.Seat.Front Power Seat Control System (W/ Memory). Dtc B2653 Lifter Sensor Malfunction

  1. Disconnect the b3*1 or a3*2 motor connector.

    1. *1: for LHD
    2. *2: for RHD

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    for LHD
    Tester Connection
    		Switch Condition
    		Specified Condition
    b3-2 (O/P) - b3-3 (GND)
    		Lifter switch on
    		4.8 to 5.1 V
    for RHD
    Tester Connection
    		Switch Condition
    		Specified Condition
    a3-2 (O/P) - a3-3 (GND)
    		Lifter switch on
    		4.8 to 5.1 V
    Text in Illustration
    *A
    		for LHD
    *B
    		for RHD
    *a
    		Front view of wire harness connector
    (to Separate Type Front Seat Cushion Spring Assembly [Lifter Motor])


NG
Go to step 4
OK


3.CHECK SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY (LIFTER MOTOR)


    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155.Seat.Front Power Seat Control System (W/ Memory). Dtc B2653 Lifter Sensor Malfunction

  1. Connect the b3*1 or a3*2 motor connector.

    1. *1: for LHD
    2. *2: for RHD

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    for LHD
    Tester Connection
    		Switch Condition
    		Specified Condition
    b3-2 (O/P) - Body ground
    		Lifter switch on
    		4.5 to 4.8 V
    for RHD
    Tester Connection
    		Switch Condition
    		Specified Condition
    a3-2 (O/P) - Body ground
    		Lifter switch on
    		4.5 to 4.8 V
    Text in Illustration
    *A
    		for LHD
    *B
    		for RHD
    *a
    		Component with harness connected
    (Separate Type Front Seat Cushion Spring Assembly [Lifter Motor])


NG
REPLACE SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY (LIFTER MOTOR) (LandCruiser RM000004673017X.html)
OK

REPLACE FRONT POWER SEAT SWITCH (LandCruiser RM000004673017X.html)

4.CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH - LIFTER MOTOR)
  1. *1: for LHD
  2. *2: for RHD

  1. Disconnect the b5*1 or a5*2 switch connector.

  1. Disconnect the b3*1 or a3*2 motor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD
    Tester Connection
    		Condition
    		Specified Condition
    b5-4 (SSRL) - b3-2 (O/P)
    		Always
    		Below 1 Ω
    b5-1 (SGND) - b3-3 (GND)
    		Always
    		Below 1 Ω
    b5-4 (SSRL) - Body ground
    		Always
    		10 kΩ or higher
    b5-1 (SGND) - Body ground
    		Always
    		10 kΩ or higher
    for RHD
    Tester Connection
    		Condition
    		Specified Condition
    a5-4 (SSRL) - a3-2 (O/P)
    		Always
    		Below 1 Ω
    a5-1 (SGND) - a3-3 (GND)
    		Always
    		Below 1 Ω
    a5-4 (SSRL) - Body ground
    		Always
    		10 kΩ or higher
    a5-1 (SGND) - Body ground
    		Always
    		10 kΩ or higher


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE FRONT POWER SEAT SWITCH (LandCruiser RM000004673017X.html)

5.INSPECT SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY (LIFTER MOTOR)


    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155.Seat.Front Power Seat Control System (W/ Memory). Dtc B2653 Lifter Sensor Malfunction

  1. Remove the separate type front seat cushion spring assembly (lifter motor) (LandCruiser RM000004673017X.html).

  1. Check if the seat cushion spring moves smoothly when the battery is connected to the lifter motor connector terminals.

    OK:
    Measurement Condition
    		Operational Direction
    Battery positive (+) → 1 (UP)
    Battery negative (-) → 4 (DOWN)
    		Seat cushion spring moves upward
    Battery positive (+) → 4 (DOWN)
    Battery negative (-) → 1 (UP)
    		Seat cushion spring moves downward


NG
REPLACE SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY (LIFTER MOTOR) (LandCruiser RM000004673017X.html)
OK


6.CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH - LIFTER MOTOR)
  1. *1: for LHD
  2. *2: for RHD

  1. Disconnect the b4*1 or a4*2 switch connector.

  1. Disconnect the b3*1 or a3*2 motor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD
    Tester Connection
    		Condition
    		Specified Condition
    b4-10 (LFT+) - b3-1 (UP)
    		Always
    		Below 1 Ω
    b4-12 (LFT-) - b3-4 (DOWN)
    		Always
    		Below 1 Ω
    b4-10 (LFT+) - Body ground
    		Always
    		10 kΩ or higher
    b4-12 (LFT-) - Body ground
    		Always
    		10 kΩ or higher
    for RHD
    Tester Connection
    		Condition
    		Specified Condition
    a4-10 (LFT+) - a3-1 (UP)
    		Always
    		Below 1 Ω
    a4-12 (LFT-) - a3-4 (DOWN)
    		Always
    		Below 1 Ω
    a4-10 (LFT+) - Body ground
    		Always
    		10 kΩ or higher
    a4-12 (LFT-) - Body ground
    		Always
    		10 kΩ or higher


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE FRONT POWER SEAT SWITCH (LandCruiser RM000004673017X.html)