Steering Wheel Installation


  1. INSTALL STEERING WHEEL ASSEMBLY

  2. INSTALL STEERING WHEEL HEATER CONTROL ASSEMBLY (w/ Steering Heater)

  3. INSTALL CRUISE CONTROL MAIN SWITCH (w/ Cruise Control System)

  4. INSTALL NO. 1 STEERING WHEEL ORNAMENT

  5. INSTALL NO. 2 STEERING WHEEL ORNAMENT

  6. INSTALL STEERING PAD SWITCH ASSEMBLY (w/ Steering Pad Switch)

  7. INSTALL STEERING PAD SWITCH RH (w/ Steering Pad Switch)

  8. INSTALL STEERING PAD

  9. INSTALL NO. 2 STEERING WHEEL LOWER COVER

  10. INSTALL NO. 3 STEERING WHEEL LOWER COVER

  11. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

  12. CHECK SRS WARNING LIGHT

Steering Wheel -- Installation



1. INSTALL STEERING WHEEL ASSEMBLY

  1. Align the matchmarks on the steering wheel assembly and steering main shaft assembly.

  1. Install the steering wheel assembly set nut.

    Torque:
    50 N*m{510 kgf*cm, 37 ft.*lbf}


2. INSTALL STEERING WHEEL HEATER CONTROL ASSEMBLY (w/ Steering Heater)

  1. Install the steering wheel heater control assembly with the 2 screws.

  1. Connect the 2 connectors and connector clamp.



3. INSTALL CRUISE CONTROL MAIN SWITCH (w/ Cruise Control System)


    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155

  1. Install the switch with the 2 screws.

  1. Connect the connector.



4. INSTALL NO. 1 STEERING WHEEL ORNAMENT

  1. Attach the claw and 3 guide pins to install the ornament.

  1. Install the 2 screws.



5. INSTALL NO. 2 STEERING WHEEL ORNAMENT

  1. Attach the claw and 3 guide pins to install the ornament.

  1. Install the 2 screws.



6. INSTALL STEERING PAD SWITCH ASSEMBLY (w/ Steering Pad Switch)

  1. Attach the 2 claws and 6 guide pins to install the steering pad switch assembly.

  1. Install the 4 screws.

  1. Connect the connector.



7. INSTALL STEERING PAD SWITCH RH (w/ Steering Pad Switch)

  1. Attach the claw and 3guide pins to install the pad switch RH.

  1. Install the 2 screws.

  1. Connect the connector.



8. INSTALL STEERING PAD

  1. Check that the ignition switch is off.

  1. Check that the cable is disconnected from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155

  1. Support the steering pad with one hand.

  1. Connect the 2 connectors to the steering pad.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.

  1. Connect the horn connector.

  1. Confirm that the groove along the circumference of the "TORX" screw is attached to the screw case and place the steering pad onto the steering wheel.

  1. Using a T30 "TORX" socket wrench, tighten the 2 screws.

    Torque:
    8.8 N*m{90 kgf*cm, 78 in.*lbf}


9. INSTALL NO. 2 STEERING WHEEL LOWER COVER


    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155.Steering Column.Power Tilt And Power Telescopic Steering Column System.Steering Wheel Installation

  1. Attach the 2 claws to install the cover.

    Text in Illustration
    *A
    		w/o Cruise Control System
    *B
    		w/ Cruise Control System


10. INSTALL NO. 3 STEERING WHEEL LOWER COVER

  1. Attach the 2 claws to install the cover.



11. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (LandCruiser RM000003YMF011X.html).


12. CHECK SRS WARNING LIGHT
(LandCruiser RM000000XFD0N3X.html)