Dtc P0717 Input Speed Sensor Circuit No Signal


DESCRIPTION

MONITOR DESCRIPTION

WIRING DIAGRAM

INSPECTION PROCEDURE

READ VALUE USING GTS (SPD (NT) AND NT SENSOR VOLTAGE)

INSPECT TRANSMISSION REVOLUTION SENSOR (NT)

CHECK HARNESS AND CONNECTOR (TRANSMISSION REVOLUTION SENSOR (NT) - ECM)

DTC P0717 Input Speed Sensor Circuit No Signal

DTC P07BF Input/Turbine Speed Sensor "A" Circuit Low

DTC P07C0 Input/Turbine Speed Sensor "A" Circuit High


DESCRIPTION

This sensor detects the rotation speed of the turbine which shows the input turbine speed of the transmission. By comparing the input turbine speed signal (NT) with the output shaft speed sensor signal (SP2), the ECM detects the shift timing of the gears and appropriately controls the engine torque and hydraulic pressure according to various conditions. As a result, the gears shift smoothly.

DTC No.
DTC Detection Condition
Trouble Area
P0717
All conditions are met for 5 seconds or more (1 trip detection logic):
(a) Park/neutral position switch D input signal is ON.
(b) Gear position is 2nd, 3rd, 4th, 5th or 6th.
(c) Transmission output shaft speed is 1000 rpm or more.
(d) The vehicle speed is 25 km/h (15.5 mph) or more.
(e) Transmission revolution sensor (NT) value is less than 300 rpm.
  1. Harness or connector
  2. Transmission revolution sensor (NT)
  3. ECM
P07BF
When the transmission revolution sensor (NT) input voltage is below 0.1 V for 4.5 seconds or more (1 trip detection logic).
  1. Harness or connector
  2. Transmission revolution sensor (NT)
  3. ECM
P07C0
When the transmission revolution sensor (NT) input voltage is higher than 1.9 V for 4.5 seconds or more (1 trip detection logic).
  1. Harness or connector
  2. Transmission revolution sensor (NT)
  3. ECM

MONITOR DESCRIPTION

The transmission revolution sensor (NT) detects the transmission input shaft speed. The ECM calculates gear shifts comparing the transmission revolution sensor (NT) with the transmission revolution sensor (SP2).
While the vehicle is operating in 2nd, 3rd, 4th, 5th or 6th gear with the shift lever in D, if the input shaft speed is less than 300 rpm*1 and the output shaft speed is more than 1000 rpm*2, the ECM interprets this as a fault, illuminates the MIL and stores the DTC.
*1: Pulse is not output or is irregularly output.
*2: The vehicle speed is 50 km/h (31 mph) or more.

WIRING DIAGRAM


Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155.Ac60F Automatic Transmission Transaxle.Automatic Transmission System (For 1Gr-Fe). Dtc P0717 Input Speed Sensor Circuit No Signal


INSPECTION PROCEDURE

NOTICE:
Perform registration and/or initialization when parts related to the automatic transmission are replaced (LandCruiser RM000000O7H0HLX.html).
HINT:
After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.
  1. Perform the D Position Shift Test in Road Test and drive the vehicle for 5 seconds or more at 50 km/h (31 mph) or more (LandCruiser RM000000W790S9X.html).
  2. Check for DTCs again (LandCruiser RM000000W7711DX.html).

DATA LIST
HINT:
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the GTS to the DLC3.

  4. Turn the ignition switch to ON.

  5. Turn the GTS on.

  6. Enter the following menus: Powertrain / Engine and ECT / Data List.

  7. According to the display on the GTS, read the Data List.

    Engine and ECT
    Tester Display
    		Measurement Item/Range
    		Normal Condition
    		Diagnostic Note
    SPD (NT)
    		Input shaft speed/
    Min.: 0 rpm
    Max.: 12750 rpm
    1. Lock-up on (after warming up the engine): Value from transmission revolution sensor (NT) equal to engine speed
    2. Lock-up off (idling with shift lever in N): Value from transmission revolution sensor (NT) nearly equal to engine speed
    		Data is displayed in increments of 50 rpm
    HINT:
    1. SPD (NT) is always 0 while driving: Open or short in the sensor or circuit.
    2. SPD (NT) is always more than 0 and less than 300 rpm while driving the vehicle at 50 km/h (31 mph) or more: Sensor trouble, improper installation, or intermittent connection trouble of the circuit.
1.READ VALUE USING GTS (SPD (NT) AND NT SENSOR VOLTAGE)

  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List

  1. In accordance with the display on the GTS, read the Data List.

    Engine and ECT
    Tester Display
    		Measurement Item/Range
    		Normal Condition
    		Diagnostic Note
    SPD (NT)
    		Input shaft speed/
    Min.: 0 rpm
    Max.: 12750 rpm
    1. Lock-up on (after warming up the engine): Value from transmission revolution sensor (NT) equal to engine speed
    2. Lock-up off (idling with shift lever in N): Value from transmission revolution sensor (NT) nearly equal to engine speed
    		Data is displayed in increments of 50 rpm
    NT Sensor Voltage
    		Transmission revolution sensor (NT) output voltage/
    Min.: 0.000 V
    Max.: 4.999 V
    		0.1 to 1.9 V: Engine idling
    		-

    Result
    Result
    		Proceed to
    Data display is not within Normal Condition range
    		A
    Data display is within Normal Condition range
    		B


B
REPLACE ECM (LandCruiser RM000000VW203EX.html)
A


2.INSPECT TRANSMISSION REVOLUTION SENSOR (NT)

  1. Remove the transmission revolution sensor (NT) (LandCruiser RM000000OE406OX.html).



  1. Connect the battery to the sensor as shown in the illustration.


    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155.Ac60F Automatic Transmission Transaxle.Automatic Transmission System (For 1Gr-Fe). Dtc P0717 Input Speed Sensor Circuit No Signal


    Text in Illustration
    *1
    		Transmission Revolution Sensor (NT)
    		*2
    		Ammeter
    *3
    		Battery
    		*4
    		Magnet
    *a
    		5 mm (0.197 in.) or less
    		-
    		-

  1. Wave a magnetic object left and right in front of the transmission revolution sensor (NT) tip (5 mm (0.197 in.) or less) to change the high/low signals while measuring the current.

    NOTICE:
    Make sure to wave the magnetic object during the inspection. The current will not change without waving the magnetic object as indicated by the arrow in the illustration.

  1. Measure the current according to the value(s) in the table below.

    Standard Current:

    Tester Connection
    		Condition
    		Specified Condition
    1 (NTO) - 2 (NTB)
    		Low signal
    		4 to 8 mA
    1 (NTO) - 2 (NTB)
    		High signal
    		12 to 16 mA


NG
REPLACE TRANSMISSION REVOLUTION SENSOR (NT) (LandCruiser RM000000OE406OX.html)
OK


3.CHECK HARNESS AND CONNECTOR (TRANSMISSION REVOLUTION SENSOR (NT) - ECM)

  1. Disconnect the C148 transmission revolution sensor (NT) connector.

  1. Disconnect the C155 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    		Condition
    		Specified Condition
    C148-2 (NTB) - C155-29 (NTB)
    		Always
    		Below 1 Ω
    C148-1 (NTO) - C155-19 (NTO)
    		Always
    		Below 1 Ω
    C148-2 (NTB) - Body ground
    		Always
    		10 kΩ or higher
    C148-1 (NTO) - Body ground
    		Always
    		10 kΩ or higher


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (LandCruiser RM000000VW203EX.html)