Tcm Installation


  1. INSTALL TCM

  2. INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (w/ Knee Airbag)

  3. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY

  4. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY (for LHD)

  5. INSTALL INSTRUMENT PANEL FINISH PLATE GARNISH (for RHD)

  6. INSTALL INSTRUMENT SIDE PANEL LH (for LHD)

  7. INSTALL INSTRUMENT SIDE PANEL RH (for RHD)

  8. INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

  9. INSTALL COWL SIDE TRIM BOARD LH (for LHD)

  10. INSTALL COWL SIDE TRIM BOARD RH (for RHD)

  11. INSTALL DOOR SCUFF PLATE ASSEMBLY LH (for LHD)

  12. INSTALL DOOR SCUFF PLATE ASSEMBLY RH (for RHD)

  13. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

  14. CHECK SRS WARNING LIGHT

Tcm -- Installation



1. INSTALL TCM

  1. Install the TCM with the 2 nuts.

    Torque:
    8.0 N*m{82 kgf*cm, 71 in.*lbf}

  1. Connect the 3 connectors.



2. INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (w/ Knee Airbag)

  1. Check that the ignition switch is off.

  1. Check that the cable is disconnected from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155

  1. Connect the connector.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.

  1. Install the airbag assembly with the 4 bolts.

    Torque:
    10 N*m{102 kgf*cm, 7 ft.*lbf}


3. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY

  1. Connect each connector and each cable.

  1. w/o Knee Airbag:

    1. Attach the 7 clips to install the lower instrument panel finish panel.

  1. w/ Knee Airbag:

    1. Attach the 14 clips to install the lower instrument panel finish panel.

  1. Install the 2 bolts <C>.

  1. Attach the 2 claws to close the cover.



4. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY (for LHD)

  1. Connect each connector.

  1. Attach the 4 clips to install the instrument panel finish panel.



5. INSTALL INSTRUMENT PANEL FINISH PLATE GARNISH (for RHD)

  1. Connect each connector.

  1. Attach the 4 clips to install the instrument panel finish plate garnish.



6. INSTALL INSTRUMENT SIDE PANEL LH (for LHD)

  1. Attach the 5 clips, claw and 3 guides to install the instrument side panel.



7. INSTALL INSTRUMENT SIDE PANEL RH (for RHD)

  1. Connect the connector.

  1. Attach the 5 clips, claw and 3 guides to install the instrument side panel.



8. INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

  1. for LHD:

    1. Attach the 2 clips and 2 guides to install the No. 1 instrument panel under cover.

    2. Install the screw.

  1. for RHD:

    1. Attach the 3 clips and 2 guides to install the No. 1 instrument panel under cover.

    2. Install the screw.



9. INSTALL COWL SIDE TRIM BOARD LH (for LHD)

  1. Attach the clip and claw to install the cowl side trim board.

  1. Install the clip.



10. INSTALL COWL SIDE TRIM BOARD RH (for RHD)
HINT:
Use the same procedure described for the LH side.


11. INSTALL DOOR SCUFF PLATE ASSEMBLY LH (for LHD)

  1. Attach the 4 clips, 10 claws and 2 guides to install the door scuff plate.



12. INSTALL DOOR SCUFF PLATE ASSEMBLY RH (for RHD)
HINT:
Use the same procedure described for the LH side.


13. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (LandCruiser RM000003YMF011X.html).


14. CHECK SRS WARNING LIGHT

  1. Check the SRS warning light (LandCruiser RM000000XFD0N3X.html).