Oil Pump Installation

Remove any old seal packing (FIPG material).

Apply seal packing to the timing gear case as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

Standard seal diameter:

5 mm (0.197 in.)

NOTICE:

After applying seal packing, install the timing gear case assembly within 3 minutes and tighten the bolts within 15 minutes.

Install a new gasket to the groove of the timing gear case.

Install 2 new O-rings to the cylinder block.

Align the "2" marks of the balanceshaft driven gear No. 1 and oil pump drive gear.

Align the mark on the oil pump drive gear with the mark on the timing gear case.

Install the timing gear case with the union bolt and 8 bolts.

Torque:

for union bolt (A):

16 N*m{163 kgf*cm, 12 ft.*lbf}

for bolt:

13 N*m{133 kgf*cm, 10 ft.*lbf}

Remove the screw plug and gasket.

Pour approximately 50 cc (3.05 cu. in.) of engine oil into the oil pump.

Install a new gasket and the screw plug.

Torque:

44 N*m{449 kgf*cm, 32 ft.*lbf}

Remove any old seal packing (FIPG material) and be careful not to drop any oil on the contact surfaces of the cylinder block, rear oil seal retainer and oil pan.

Install a new gasket to the cylinder block.

Apply seal packing in a continuous line as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

Standard seal diameter:

4 mm (0.157 in.)

NOTICE:

1. Remove any oil from the contact surface.
   
2. Install the oil pan within 3 minutes after applying seal packing.
   
3. Do not start the engine for at least 2 hours after installation.
   

Install the oil pan with the 22 bolts and 2 nuts.

Torque:

15 N*m{148 kgf*cm, 11 ft.*lbf}

Install a new gasket and the oil strainer with the 2 nuts.

Torque:

8.0 N*m{82 kgf*cm, 71 in.*lbf}

Remove any old seal packing (FIPG material).

Apply seal packing to the No. 2 oil pan as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

Standard seal diameter:

4 mm (0.157 in.)

NOTICE:

1. Remove any oil from the contact surface.
   
2. Install the No. 2 oil pan within 3 minutes after applying seal packing.
   
3. Do not start the engine for at least 2 hours after installation.
   

Install the No. 2 oil pan with the 13 bolts and 2 nuts.

Torque:

9.0 N*m{92 kgf*cm, 80 in.*lbf}

Position the crankshaft timing gear with timing mark 1 facing forward.

Align the key groove of the crankshaft timing gear with the set key on the crankshaft.

Using SST and a hammer, tap on the timing gear to install it.

SST

09223-00010

Install a new O-ring and the supply pump with the 2 nuts.

Torque:

21 N*m{214 kgf*cm, 15 ft.*lbf}

Temporarily install the injection gear with the nut.

HINT:

Fit the key (protrusion) of the supply pump into the key slot of the injection gear.

Align the "3" marks of the balanceshaft driven gear No. 2 and injection gear.

Install a new O-ring to the injection gear.

Install the injection gear set nut.

Using SST, tighten the nut.

SST

09960-10010(09962-01000,09963-01000)

Torque:

64 N*m{653 kgf*cm, 47 ft.*lbf}

Apply a coat of engine oil to the No. 1 idle gear shaft.

Install the gear shaft as shown in the illustration.

Align the "5" timing marks of the idle gear and crankshaft timing gear.

Using SST, turn the injection gear and align the "4" timing marks of the idle gear and injection gear, and then mesh the gears.

SST

09960-10010(09962-01000,09963-00700)

Position the thrust plate with the protrusion facing forward.

Align the bolt holes and install the thrust plate with the 2 bolts.

Torque:

50 N*m{510 kgf*cm, 37 ft.*lbf}

Remove the service bolt.

Align the key groove of the sensor plate with the set key.

Install the sensor plate with the cupped side facing outward.

Remove any old seal packing (FIPG material).

Apply seal packing to the timing gear cover as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

Standard seal diameter:

4 mm (0.157 in.)

NOTICE:

After applying seal packing, install the timing gear cover within 3 minutes and tighten the bolts within 15 minutes.

Install a new O-ring to the timing gear case.

Install the timing gear cover with the 14 bolts and 2 nuts.

Torque:

13 N*m{133 kgf*cm, 10 ft.*lbf}

Install a new gasket and the water pump with the 5 bolts and 2 nuts.

Torque:

13 N*m{133 kgf*cm, 10 ft.*lbf}

Apply seal packing (FIPG) to the specified areas shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

NOTICE:

After applying seal packing, install the No. 2 timing belt cover within 3 minutes and tighten the bolts and nut within 15 minutes.

Install the No. 2 timing belt cover with the 4 bolts and nut.

Torque:

10 N*m{102 kgf*cm, 7 ft.*lbf}

Install the camshaft timing pulley.

Install the bolt of the camshaft timing pulley while holding the camshaft with a wrench.

Torque:

98 N*m{1000 kgf*cm, 72 ft.*lbf}

Install 4 new injection nozzle seats to the cylinder head.

Apply a small amount of clean engine oil to 4 new O-rings.

Install an O-ring to each injector as shown in the illustration.

Insert the 4 injectors into the cylinder head.

NOTICE:

1. Insert the injector until it touches the injection nozzle seat surface.
   
2. After installing the injector to the cylinder head, the O-ring may prevent the injector from fully seating. If so, pull out the injector and reinstall it.
   
3. Always return an injector to the same place it was removed from.
   

For an injector that has been replaced with a new injector, register the injector compensation code (LandCruiser RM0000012XK0ARX.html).

Temporarily install 4 new washers and the 4 No. 1 nozzle holder clamps with the 4 bolts.

HINT:

Apply a small amount of engine oil to the threads and under the heads of the clamp bolts.

NOTICE:

1. 
   
2. The fork portion of the nozzle holder clamp must be set on the injector.
   
3. Before tightening the bolts, check that the No. 1 nozzle holder clamp is set properly.
   
4. When installing the clamp bolts, first tighten them by hand until they cannot be turned further. Then, tighten the bolts to the specified torque in the following step.
   
5. When tightening the bolts, pay attention so as not to tilt the bolt and the clamp.
   
6. Do not reuse the washer.
   
7. If the nozzle leakage pipe is accidentally tightened beyond the torque specification, it must be replaced.
   

   Text in Illustration

   *1	Nozzle Clamp Holder

Temporarily install the 4 injection pipes with the union nuts.

HINT:

To position the injectors, loosely tighten the union nut.

Check the nozzle leakage pipe. Check that there are no scratches or dents on the 5 union seal surfaces.
If scratches or dents are present, replace the nozzle leakage pipe.

Set the leakage pipe and 5 new gaskets in place.

Apply a small amount of oil to the 4 injector hollow screws and union bolt.

Temporarily install the leakage pipe with the 4 injector hollow screws and union bolt.

Tighten the 4 holder clamp bolts.

Torque:

22 N*m{220 kgf*cm, 16 ft.*lbf}

Tighten the 4 hollow screws in order from 1 to 4.

Torque:

16 N*m{163 kgf*cm, 12 ft.*lbf}

NOTICE:

If a hollow screw is accidentally tightened beyond the torque specification, it must be replaced.

Tighten the union bolt.

Torque:

13 N*m{127 kgf*cm, 9 ft.*lbf}

NOTICE:

If the union bolt is accidentally tightened beyond the torque specification, it must be replaced.

Remove the 4 injection pipes.

Check that there are no leaks from the nozzle leakage pipe connection.

1. Install the gasket and No. 2 nozzle leakage pipe to the cylinder head with SST (check valve).
   

   Part No.:

   23762-27010 (No. 2 nozzle leakage pipe)
   

   90904-30012 (Gasket)
   

   SST

   09280-00010
   

   Torque:

   21 N*m{214 kgf*cm, 15 ft.*lbf}

2. Apply a small amount of soapy water (or other fluid for detecting fuel leakage) on the nozzle leakage pipe connection.
   





3. Install SST (turbocharger pressure gauge) to the fuel return side of the leakage pipe, maintain 100 kPa (1.0 kgf/cm², 15 psi) of pressure for 60 seconds and check that no bubbles form.
   

   SST

   09992-00242
   

4. After checking for fuel leaks, wipe off the soapy water from the leakage pipe connection.
   

5. Remove SST, the No. 2 nozzle leakage pipe and gasket.
   

   NOTICE:

   Never reinstall the disassembled union bolt to the engine.

Install 4 new No. 3 cylinder head cover gaskets to the cylinder head cover in the directions shown in the illustration.

NOTICE:

1. Do not install the No. 3 cylinder head cover gaskets at an angle.
   
2. Check that there is no foreign matter at the installation location of the No. 3 cylinder head cover gaskets.
   

Remove any old seal packing (FIPG material) from the cylinder head.

Apply seal packing to the areas shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

NOTICE:

1. Remove any oil from the contact surface.
   
2. Install the cylinder head cover within 3 minutes after applying seal packing.
   
3. Do not start the engine for at least 2 hours after installation.
   

Install a new gasket and the cylinder head cover with the 10 bolts and 2 nuts.

Torque:

9.0 N*m{92 kgf*cm, 80 in.*lbf}

Install 4 new nozzle holder seals.

Install the No. 1 oil pan cover with the 4 bolts.

Torque:

9.0 N*m{92 kgf*cm, 80 in.*lbf}

Install the No. 1 vacuum transmitting pipe with the bolt and nut.

Torque:

for bolt:

13 N*m{133 kgf*cm, 10 ft.*lbf}

for nut:

8.0 N*m{82 kgf*cm, 71 in.*lbf}

Check that the injection gear in the timing gear case moves back and forth smoothly.

Install the pump drive shaft pulley and No. 2 camshaft timing pulley flange with the 4 bolts.

Torque:

31 N*m{316 kgf*cm, 23 ft.*lbf}

Move the pump drive shaft pulley back and forth to check the thrust clearance of the injection pump drive shaft.

Standard thrust clearance:

0.15 to 0.55 mm (0.00590 to 0.0217 in.)

Temporarily install the fuel inlet pipe with the union nuts.

NOTICE:

1. When replacing the fuel supply pump, it is necessary to replace the fuel inlet pipe with a new one.
   
2. Keep the fuel inlet pipe free of foreign matter.
   

Using a 17 mm union nut wrench, tighten the fuel inlet pipe union nut on the common rail side.

Torque:

35 N*m{357 kgf*cm, 26 ft.*lbf}

NOTICE:

Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (LandCruiser RM000003YMD00TX.html).

Using a 17 mm union nut wrench, tighten the fuel inlet pipe union nut on the fuel supply pump side.

Torque:

35 N*m{357 kgf*cm, 26 ft.*lbf}

NOTICE:

Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (LandCruiser RM000003YMD00TX.html).

Install the manifold stay with vacuum switching valve with the 2 bolts and connect the No. 3 vacuum transmitting hose and No. 4 vacuum transmitting hose.

Torque:

19 N*m{194 kgf*cm, 14 ft.*lbf}

NOTICE:

Make sure the vacuum hose color matches the connection area color.

w/ EGR Cooler:
Connect the No. 3 vacuum transmitting hose.

w/ EGR System:
Connect the No. 2 vacuum transmitting hose and No. 3 vacuum transmitting hose.

NOTICE:

1. Make sure the vacuum hose color matches the connection area color.
   
2. Push on the hose until it reaches the bent part of the pipe.
   

Connect the No. 1 vacuum transmitting hose.

Connect the vacuum switching valve connector.

1. w/o EGR System:
   Connect the connector.
   

2. w/ EGR System without EGR Cooler:
   Connect the 2 connectors.
   

3. w/ EGR System with EGR Cooler:
   Connect the 3 connectors.
   

Set a new gasket on the intake manifold.

NOTICE:

Make sure the claw of the gasket face the intake manifold as shown in the illustration.

Install the intake air connector with diesel throttle body with the 3 bolts.

Torque:

20 N*m{204 kgf*cm, 15 ft.*lbf}

NOTICE:

Tighten the bolts in the order shown in the illustration.

Connect the throttle position sensor connector.

Temporarily install the air connector stay with the 3 bolts.

Tighten the bolt labeled A.

Torque:

20 N*m{204 kgf*cm, 15 ft.*lbf}

Tighten the 2 bolts labeled B.

Torque:

20 N*m{204 kgf*cm, 15 ft.*lbf}

Temporarily install the No. 1, No. 2 and No. 3 injection pipes with the union nuts.

Install the No. 2 and No. 3 injection pipe clamps with the 2 bolts and 2 nuts as shown in the illustration.

Torque:

5.0 N*m{51 kgf*cm, 44 in.*lbf}

HINT:

If the painted mark on the No. 2 injection pipe has disappeared, use the illustration as a reference to install the clamps.

Using a 17 mm union nut wrench, tighten the injection pipe union nuts on the common rail side.

Torque:

35 N*m{357 kgf*cm, 26 ft.*lbf}

NOTICE:

Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (LandCruiser RM000003YMD00TX.html).

Using a 17 mm union nut wrench, tighten the injection pipe union nuts on the injector side.

Torque:

35 N*m{357 kgf*cm, 26 ft.*lbf}

NOTICE:

Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (LandCruiser RM000003YMD00TX.html).

Install the throttle body bracket with the 2 bolts.

Torque:

20 N*m{204 kgf*cm, 15 ft.*lbf}

Install the gas filter with gas filter bracket with the bolt.

Torque:

20 N*m{204 kgf*cm, 15 ft.*lbf}

Connect the vacuum hose.

Install the electric EGR control valve (LandCruiser RM000002RK6045X.html).

Align the keyway of the pulley with the key located on the crankshaft, and then slide the pulley into place to install it.

Using SST, install the pulley bolt.

SST

09213-58014
09330-00021

Torque:

365 N*m{3722 kgf*cm, 269 ft.*lbf}

Using a 10 mm hexagon wrench, install a new washer and the No. 1 timing belt idler with the bolt.

Torque:

35 N*m{357 kgf*cm, 26 ft.*lbf}

Check that the idler pulley moves smoothly.
If the idler pulley does not move smoothly, check the installation condition of the idler and washer.

Install the timing belt (LandCruiser RM000001479026X.html).

Attach the clamp and install the crankshaft position sensor with the bolt.

Torque:

8.5 N*m{87 kgf*cm, 75 in.*lbf}

Install the camshaft position sensor with the bolt.

Torque:

8.5 N*m{87 kgf*cm, 75 in.*lbf}

Install a new O-ring and the vane pump with the 2 nuts.

Torque:

41 N*m{418 kgf*cm, 30 ft.*lbf}

Install 2 new O-rings to the vacuum pump.

Install the vacuum pump with the 2 nuts.

Torque:

21 N*m{210 kgf*cm, 15 ft.*lbf}

Install the timing gear cover insulator with the bolt.

Torque:

8.0 N*m{82 kgf*cm, 71 in.*lbf}

Install the No. 2 cylinder head cover with the 4 bolts.

Torque:

for bolt A:

18 N*m{184 kgf*cm, 13 ft.*lbf}

for bolt B:

8.0 N*m{82 kgf*cm, 71 in.*lbf}

Install a new O-ring to the engine oil level dipstick guide.

Apply a small amount of clean engine oil to the O-ring.

Install the engine oil level dipstick guide to the cylinder block sub-assembly with the 2 bolts.

Torque:

8.0 N*m{82 kgf*cm, 71 in.*lbf}

Install the engine oil level dipstick.

Connect the 2 ventilation hoses and install the ventilation pipe to the cylinder head cover to the cylinder head sub-assembly with the bolt.

Torque:

18 N*m{184 kgf*cm, 13 ft.*lbf}

Type A
Connect the No. 3 turbo water hose and No. 4 turbo water hose to the ventilation pipe, and slide the 2 clamps to secure the hose.

Install the No. 1 compressor mounting bracket with the 5 bolts.

Torque:

21 N*m{214 kgf*cm, 15 ft.*lbf}

Install the generator bracket with the bolts.

Torque:

21 N*m{214 kgf*cm, 15 ft.*lbf}

Install the generator with the 2 bolts.

Torque:

for bolt A:

62 N*m{632 kgf*cm, 46 ft.*lbf}

for bolt B:

21 N*m{214 kgf*cm, 15 ft.*lbf}

Install 2 engine hangers with 2 bolts as shown in the illustration.

HINT:

Part No.

Torque:

for No. 1 engine hanger:

25 N*m{255 kgf*cm, 18 ft.*lbf}

for No. 2 engine hanger:

60 N*m{612 kgf*cm, 44 ft.*lbf}

NOTICE:

Install the engine hangers with new bolts.

Attach an engine sling device and hang the engine with a chain block.

Remove the engine from the engine stand.

Install the engine (LandCruiser RM0000045F8013X.html).

Add new engine oil.

Standard Oil Grade:

Oil Grade	Oil Viscosity (SAE)
G-DLD1, API CF-4, CF or ACEA B1 (You may also use API CE or CD)	- 5W-30 - 10W-30 - 15W-40 - 20W-50

Standard Capacity:

Item	Specified Condition
Drain and refill without oil filter change	6.7 liters (7.1 US qts, 5.9 Imp. qts)
Drain and refill with oil filter change	7.0 liters (7.4 US qts, 6.2 Imp. qts)
Dry fill	7.5 liters (7.9 US qts, 6.6 Imp. qts)

Install the oil filler cap.

Using the hand pump mounted on the fuel filter cap, bleed the air from the fuel system. Continue pumping until the pump resistance increases.

NOTICE:

1. The maximum hand pump pumping speed is 2 strokes per second.
   
2. The hand pump must be pushed with a full stroke during pumping.
   
3. When the fuel pressure at the supply pump inlet port reaches a saturated pressure, the hand pump resistance increases.
   
4. If pumping is interrupted during the air bleeding process, fuel in the fuel line may return to the fuel tank. Continue pumping until the hand pump resistance increases.
   
5. If the hand pump resistance does not increase despite consecutively pumping 200 times or more, there may be a fuel leak between the fuel tank and fuel filter, the hand pump may be malfunctioning, or the vehicle may have run out of fuel.
   
6. If air bleeding using the hand pump is incomplete, the common rail pressure does not rise to the pressure range necessary for normal use and the engine cannot be started.
   

Start the engine.

NOTICE:

1. Even if air bleeding using the hand pump has been completed, the starter may need to be cranked for 10 seconds or more to start the engine.
   
2. Do not crank the engine continuously for more than 20 seconds. The battery may be discharged.
   
3. Use a fully-charged battery.
   

1. When the engine can be started, proceed to the next step.
   

2. If the engine cannot be started, bleed the air again using the hand pump until the hand pump resistance increases (refer to the procedures above). Then start the engine.
   

Turn the ignition switch off.

Connect the intelligent tester to the DLC3.

Turn the ignition switch on (IG) and turn the intelligent tester on.

Clear the DTCs (LandCruiser RM000000PDK1DJX.html).

Start the engine.*1

Enter the following menus: Powertrain / Engine and ECT / Active Test / Test the Fuel Leak.*2

Perform the following test 5 times with on/off intervals of 10 seconds: Active Test / Test the Fuel Leak.*3

Allow the engine to idle for 3 minutes or more after performing the Active Test for the 5th time.

HINT:

When the Active Test "Test the Fuel Leak" is used to change the pump control mode, the actual fuel pressure inside the common rail drops below the target fuel pressure when the Active Test is off, but this is normal and does not indicate a pump malfunction.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Read Current DTCs.

Clear the DTCs (LandCruiser RM000000PDK1DJX.html).

HINT:

It is necessary to clear the DTCs as DTC P1604 or P1605 may be stored when air is bled from the fuel system after replacing or repairing fuel system parts.

Repeat steps *1 to *3.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Read Current DTCs.

OK:

No DTCs are output.

Tighten the radiator drain cock plug by hand.

Tighten the cylinder block drain cock plug.

Torque:

8.0 N*m{82 kgf*cm, 71 in.*lbf}

Fill the radiator with TOYOTA Super Long Life Coolant (SLLC) to the B line of the reservoir tank.

Standard Capacity:

Item		Specified Condition
for Automatic Transmission	w/ Rear Heater	14.9 liters (15.7 US qts, 13.1 Imp. qts)
	w/o Rear Heater	13.1 liters (13.8 US qts, 11.5 Imp. qts)
for Manual Transmission	w/ Rear Heater	15.0 liters (15.8 US qts, 13.2 Imp. qts)
	w/o Rear Heater	13.2 liters (13.9 US qts, 11.6 Imp. qts)

HINT:

1. TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).
   
2. Please contact your TOYOTA dealer for further details.
   
3. for Cold Area Specification Vehicles:
   Please contact any authorized TOYOTA dealer or repairer or another duly qualified and equipped professional for further details.
   

NOTICE:

Never use water as a substitute for engine coolant.

Press the inlet and outlet radiator hoses several times by hand, and then check the level of the coolant.
If the coolant level drops below the B line, add TOYOTA SLLC to the B line.

Install the radiator reservoir cap.

Using a wrench, install the vent plug.

Torque:

2.0 N*m{20 kgf*cm, 18 in.*lbf}

Bleed air from the cooling system.

1. Warm up the engine until the thermostat opens. While the thermostat is open, circulate the coolant for several minutes.
   

2. Maintain the engine speed at 2500 to 3000 rpm.
   

3. Press the inlet and outlet radiator hoses several times by hand to bleed air.
   

   CAUTION:

   When pressing the radiator hoses:

   1. Wear protective gloves.
      
   2. Be careful as the radiator hoses are hot.
      
   3. Keep your hands away from the radiator fan.
      

4. Stop the engine and wait until the coolant cools down to ambient temperature.
   

   CAUTION:

   Do not remove the radiator reservoir cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

After the coolant cools down, check that the coolant level is at the FULL line.
If the coolant level is below the FULL line, add TOYOTA SLLC to the FULL line.

Start the engine. Make sure that there are no oil leaks from the areas that were worked on.

Check that there are no leaks from any part of the fuel system when the engine is stopped. If there is fuel leakage, repair or replace parts as necessary.

Start the engine and check that there are no leaks from any part of the fuel system. If there is fuel leakage, repair or replace parts as necessary.

Disconnect the return hose from the common rail.

Start the engine and check for fuel leaks from the return pipe.
If there is fuel leakage, replace the common rail.

Connect the intelligent tester to the DLC3.

Start the engine and turn the intelligent tester on.

Select the Fuel Leak test from the Active Test mode on the intelligent tester.

If the intelligent tester is not available, fully depress the accelerator pedal quickly. Increase the engine speed to the maximum and maintain that speed for 2 seconds. Repeat this operation several times.

Check that there are no leaks from any part of the fuel system.

NOTICE:

A return pipe leakage of less than 10 cc (0.6 cu in.) per minute is acceptable.

Reconnect the return hose to the common rail.

Connect the intelligent tester to the DLC3.

If a tester is not available, connect the tester probe of a tachometer to terminal 9 (TAC) of the DLC3 with SST.

SST

09843-18040

Inspect the idle speed.

HINT:

1. Make sure that the engine is warmed up.
   
2. Make sure that the A/C switch is off.
   
3. w/ DPF:
   Make sure that PM regeneration is not being performed.
   

1. Start the engine and measure the idle speed.
   

   Idle Speed:

   Item	Specified Condition
   for Automatic Transmission	650 to 750 rpm
   for Manual Transmission	610 to 710 rpm

Inspect the maximum speed.

1. Start the engine.
   

2. Fully depress the accelerator pedal.
   

3. Measure the maximum speed.
   

   Maximum Speed:

   4450 to 4750 rpm
   

If the tester probe of a tachometer is connected to the DLC3, disconnect the tester probe together with SST from terminal 9 of the DLC3.

Disconnect the intelligent tester from the DLC3.

Warm up the engine, stop the engine and wait 5 minutes. The engine oil level should be between the dipstick low level mark and full level mark.
If low, check for leakage and add oil up to the full level mark.

NOTICE:

Do not fill engine oil above the full level mark.

HINT:

A certain amount of engine oil will be consumed while driving. In the following situations, engine oil consumption may increase, and engine oil may need to be refilled in between oil maintenance intervals.

1. When the engine is new, for example directly after purchasing the vehicle or after replacing the engine.
   
2. If low quality engine oil or oil of an inappropriate viscosity is used.
   
3. When driving at high engine speed or with a heavy load, when towing, or when driving while accelerating or decelerating frequently.
   
4. When leaving the engine idling for a long time, or when driving frequently through heavy traffic.
   

Install the No. 1 engine under cover with the 4 bolts.

Torque:

29 N*m{296 kgf*cm, 21 ft.*lbf}

Install the lower front bumper cover with the clip and 5 bolts.

Torque:

8.0 N*m{82 kgf*cm, 71 in.*lbf}