Dtc P0102 Mass Air Flow Circuit Low


DESCRIPTION

MONITOR DESCRIPTION

MONITOR STRATEGY

CONFIRMATION DRIVING PATTERN

WIRING DIAGRAM

INSPECTION PROCEDURE

READ DTC OUTPUT

INSPECT MASS AIR FLOW METER SUB-ASSEMBLY (POWER SOURCE VOLTAGE)

CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)

INSPECT MASS AIR FLOW METER SUB-ASSEMBLY

CHECK HARNESS AND CONNECTOR (SENSOR GROUND)

CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)

CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - NO. 1 INTEGRATION RELAY)

DTC P0102 Mass Air Flow Circuit Low

DTC P0103 Mass Air Flow Circuit High


DESCRIPTION

The mass air flow meter sub-assembly is a sensor that measures the amount of air flowing through the throttle valve.
The ECM uses this information to determine the fuel injection time and to provide the appropriate air-fuel ratio.
Inside the mass air flow meter sub-assembly, there is a heated platinum wire which is exposed to the flow of intake air.
By applying a specific electrical current to the wire, the ECM heats it to a given temperature. The flow of incoming air cools both the wire and an internal thermistor, affecting their resistance. To maintain a constant current value, the ECM varies the voltage applied to the wire and internal thermistor. The voltage level is proportional to the airflow through the sensor, and the ECM uses it to calculate the intake air volume.
The circuit is constructed so that the platinum hot wire and temperature sensor create a bridge circuit, and the power transistor is controlled so that the potentials of A and B remain equal to maintain the predetermined temperature.
HINT:
When either of these DTCs is stored, the ECM enters fail-safe mode. During fail-safe mode, the ignition timing is calculated by the ECM according to the engine speed and throttle valve position. The ECM continues operating in fail-safe mode until a pass condition is detected.

Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155.2Tr-Fe Engine Control.Sfi System. Dtc P0102 Mass Air Flow Circuit Low


DTC No.
DTC Detection Condition
Trouble Area
P0102
Mass air flow meter sub-assembly voltage is below 0.2 V for 3 seconds (1 trip detection logic).
  1. Open or short in mass air flow meter sub-assembly circuit
  2. Mass air flow meter sub-assembly
  3. ECM
P0103
Mass air flow meter sub-assembly voltage is higher than 4.9 V for 3 seconds (1 trip detection logic).
  1. Open or short in mass air flow meter sub-assembly circuit
  2. Mass air flow meter sub-assembly
  3. ECM

HINT:
When either of these DTCs is stored, check the air flow rate by entering the following menus: Powertrain / Engine and ECT / Data List / All Data / MAF.

MAF (gm/sec)
Malfunction
Approximately 0.0
  1. Open in mass air flow meter sub-assembly power source circuit
  2. Open or short in VG circuit
160.0 or more
Open in E2G circuit

MONITOR DESCRIPTION

If there is a defect in the mass air flow meter sub-assembly or an open or short circuit, the voltage level deviates from the normal operating range. The ECM interprets this deviation as a malfunction in the mass air flow meter sub-assembly and stores a DTC.
Example:
When the sensor output voltage remains below 0.2 V, or higher than 4.9 V for more than 3 seconds, the ECM stores a DTC.
If the malfunction is not repaired successfully, a DTC is stored 3 seconds after the engine is next started.

MONITOR STRATEGY


Frequency of Operation
Continuous

CONFIRMATION DRIVING PATTERN

  1. Connect the GTS to the DLC3.
  2. Turn the ignition switch to ON and turn the GTS on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the GTS on.
  6. Wait 5 seconds or more.
  7. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
  8. Read the pending DTCs.
    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.
  9. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  10. Input the DTC: P0102, P0103.
  11. Check the DTC judgment result.

    GTS Display
    		Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit
    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.

WIRING DIAGRAM


Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155.2Tr-Fe Engine Control.Sfi System. Dtc P0102 Mass Air Flow Circuit Low


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
HINT:
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
1.READ DTC OUTPUT

  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read DTCs.

    Result
    Result
    		Proceed to
    DTC P0102 is output
    		A
    DTC P0103 is output
    		B


B
Go to step 5
A


2.INSPECT MASS AIR FLOW METER SUB-ASSEMBLY (POWER SOURCE VOLTAGE)
Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155.2Tr-Fe Engine Control.Sfi System. Dtc P0102 Mass Air Flow Circuit Low

  1. Disconnect the mass air flow meter sub-assembly connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    		Switch Condition
    		Specified Condition
    C33-1 (+B) - Body ground
    		Ignition switch ON
    		11 to 14 V
    Text in Illustration
    *a
    		Front view of wire harness connector
    (to Mass Air Flow Meter sub-assembly)


NG
Go to step 7
OK


3.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)

  1. Disconnect the mass air flow meter sub-assembly connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    		Condition
    		Specified Condition
    C33-3 (VG) - C154-24 (VG)
    		Always
    		Below 1 Ω
    C33-2 (E2G) - C154-32 (E2G)
    		Always
    		Below 1 Ω
    C33-3 (VG) or C154-24 (VG) - Body ground
    		Always
    		10 kΩ or higher


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.INSPECT MASS AIR FLOW METER SUB-ASSEMBLY

  1. Inspect the mass air flow meter sub-assembly (LandCruiser RM000001L4A00YX.html).

    HINT:
    Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly (LandCruiser RM000004NJC03XX.html).


NG
REPLACE MASS AIR FLOW METER SUB-ASSEMBLY (LandCruiser RM000002VE200IX.html)
OK

REPLACE ECM (LandCruiser RM000000VW203EX.html)

5.CHECK HARNESS AND CONNECTOR (SENSOR GROUND)

  1. Disconnect the mass air flow meter sub-assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    		Condition
    		Specified Condition
    C154-32 (E2G) - Body ground
    		Always
    		Below 1 Ω
    HINT:
    Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly (LandCruiser RM000004NJC03XX.html).


NG
Go to step 6
OK

REPLACE MASS AIR FLOW METER SUB-ASSEMBLY (LandCruiser RM000002VE200IX.html)

6.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)

  1. Disconnect the mass air flow meter sub-assembly connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    		Condition
    		Specified Condition
    C33-2 (E2G) - C154-32 (E2G)
    		Always
    		Below 1 Ω


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (LandCruiser RM000000VW203EX.html)

7.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - NO. 1 INTEGRATION RELAY)

  1. Disconnect the mass air flow meter sub-assembly connector.

  1. Remove the No. 1 integration relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    		Condition
    		Specified Condition
    C33-1 (+B) - 1B-4
    		Always
    		Below 1 Ω
    C33-1 (+B) or 1B-4 - Body ground
    		Always
    		10 kΩ or higher


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

CHECK ECM POWER SOURCE CIRCUIT (LandCruiser RM0000027690EIX.html)