Dtc P0191 Fuel Rail Pressure Sensor Circuit Range / Performance


DESCRIPTION

WIRING DIAGRAM

INSPECTION PROCEDURE

READ VALUE USING GTS (COMMON RAIL PRESSURE AND TARGET COMMON RAIL PRESSURE)

CHECK HARNESS AND CONNECTOR (FUEL PRESSURE SENSOR - ECM)

REPAIR OR REPLACE HARNESS OR CONNECTOR

CHECK WHETHER DTC OUTPUT RECURS (DTC P0191)

REPLACE COMMON RAIL ASSEMBLY

BLEED AIR FROM FUEL SYSTEM

CHECK WHETHER DTC OUTPUT RECURS (DTC P0191)

REPLACE ECM

CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

DTC P0191 Fuel Rail Pressure Sensor Circuit Range / Performance


DESCRIPTION

HINT:
Refer to DTC P0087 (LandCruiser RM0000018800CBX_01.html).

P0191
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Idling for 1 second or more
The difference between the main and sub voltage outputs of the fuel pressure sensor is 0.04 V or less, or 1.06 V or higher for 1 second or more (1 trip detection logic).
  1. Open or short in fuel pressure sensor circuit
  2. Fuel pressure sensor (common rail assembly)
  3. ECM

Related Data List
DTC No.
Data List
P0191
  1. Common Rail Pressure
  2. Target Common Rail Pressure

WIRING DIAGRAM

Refer to DTC P0087 (LandCruiser RM0000018800CBX_06.html).

INSPECTION PROCEDURE

NOTICE:
After replacing the ECM, the new ECM needs registration (LandCruiser RM0000012XK0AUX.html) and initialization (LandCruiser RM000000TIN08HX.html).
HINT:
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
1.READ VALUE USING GTS (COMMON RAIL PRESSURE AND TARGET COMMON RAIL PRESSURE)

  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG) and turn the GTS on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Common Rail Pressure and Target Common Rail Pressure.

  1. Start the engine.

  1. Check the change in the values for the data list items above when increasing the engine speed from idling to 3000 rpm with no load.

    Result
    Result
    		Proceed to
    Common Rail Pressure is always 10000 kPa or less
    or
    Common Rail Pressure is always 200000 kPa or higher
    		A
    Except above
    		B

    HINT:
    Normally, "Common Rail Pressure" is within 5000 kPa of "Target Common Rail Pressure".


B
Go to step 4
A


2.CHECK HARNESS AND CONNECTOR (FUEL PRESSURE SENSOR - ECM)

  1. Disconnect the fuel pressure sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    		Condition
    		Specified Condition
    r8-5 (PR) - C151-18 (PCR1)
    		Always
    		Below 1 Ω
    r8-2 (PR2) - C152-26 (PCR2)
    		Always
    		Below 1 Ω
    r8-1 (VCS) - C152-33 (VCS)
    		Always
    		Below 1 Ω
    r8-6 (VC) - C151-28 (VCM)
    		Always
    		Below 1 Ω
    r8-4 (E2) - C151-19 (E2M)
    		Always
    		Below 1 Ω
    r8-3 (E2S) - C152-25 (E2S)
    		Always
    		Below 1 Ω
    r8-5 (PR) or C151-18 (PCR1) - Body ground and other terminals
    		Always
    		10 kΩ or higher
    r8-2 (PR2) or C152-26 (PCR2) - Body ground and other terminals
    		Always
    		10 kΩ or higher
    r8-1 (VCS) or C152-33 (VCS) - Body ground and other terminals
    		Always
    		10 kΩ or higher
    r8-6 (VC) or C151-28 (VCM) - Body ground and other terminals
    		Always
    		10 kΩ or higher

  1. Reconnect the fuel pressure sensor connector.

  1. Reconnect the ECM connector.



OK
Go to step 5

NG
Go to step 3

3.REPAIR OR REPLACE HARNESS OR CONNECTOR

  1. Repair or replace the harness or connector.


NEXT


4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0191)

  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG) and turn the GTS on.

  1. Clear the DTCs (LandCruiser RM000000PDK1E5X.html).

  1. Let the engine idle for 1 second.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.

    Result
    Result
    		Proceed to
    DTC P0191 is output
    		A
    No DTC is output
    		B



B
END
A


5.REPLACE COMMON RAIL ASSEMBLY

  1. Replace the common rail assembly (LandCruiser RM000005UI0000X.html).


NEXT


6.BLEED AIR FROM FUEL SYSTEM

  1. Bleed the air from the fuel system (LandCruiser RM000002SY803FX_01_0002.html).


NEXT


7.CHECK WHETHER DTC OUTPUT RECURS (DTC P0191)

  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG) and turn the GTS on.

  1. Clear the DTCs (LandCruiser RM000000PDK1E5X.html).

  1. Let the engine idle for 1 second or more.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.

    Result
    Result
    		Proceed to
    DTC P0191 is output
    		A
    No DTC is output
    		B



B
END
A


8.REPLACE ECM

  1. Replace the ECM (LandCruiser RM0000013Z002DX.html).


NEXT


9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG) and turn the GTS on.

  1. Clear the DTCs (LandCruiser RM000000PDK1E5X.html).

  1. Let the engine idle for 1 second or more.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Confirm that the DTC is not output again.


NEXT

END