Can Communication System (W/ Vsc) Steering Angle Sensor Communication Stop Mode


DESCRIPTION

WIRING DIAGRAM

INSPECTION PROCEDURE

DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CHECK FOR OPEN IN CAN BUS WIRE (STEERING ANGLE SENSOR BRANCH WIRE)

CHECK HARNESS AND CONNECTOR (STEERING ANGLE SENSOR - BATTERY AND BODY GROUND)

CAN COMMUNICATION SYSTEM (w/ VSC) - Steering Angle Sensor Communication Stop Mode


DESCRIPTION


Detection Item
Symptom
Trouble Area
Steering Angle Sensor Communication Stop Mode
When either condition below is met:
  1. Steering Angle Sensor is not displayed on "Bus Check".
  2. "Steering Angle Sensor Communication Stop Mode" in "DTC Combination Table" applies.
  1. Power source or inside steering angle sensor
  2. Steering angle sensor branch wire or connector
  3. Spiral cable (steering angle sensor)

WIRING DIAGRAM


Toyota Fortuner. Ggn50, 60 Kun51, 61 Tgn51 Lan50.Can Communication.Can Communication System (W/ Vsc).Can Communication System (W/ Vsc) Steering Angle Sensor Communication Stop Mode


INSPECTION PROCEDURE

HINT:
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.
1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and the branch wire.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
    NOTICE:
    When disconnecting the cable from the negative (-) battery terminal, some systems need to be initialized after the cable is reconnected (Toyota Fortuner RM000002HD2002X.html).

NEXT


2.CHECK FOR OPEN IN CAN BUS WIRE (STEERING ANGLE SENSOR BRANCH WIRE)


    Toyota Fortuner. Ggn50, 60 Kun51, 61 Tgn51 Lan50.Can Communication.Can Communication System (W/ Vsc).Can Communication System (W/ Vsc) Steering Angle Sensor Communication Stop Mode

  1. Disconnect the S23 steering angle sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    		Switch Condition
    		Specified Condition
    S23-4 (CANH) - S23-3 (CANL)
    		Ignition switch off
    		54 to 69 Ω


NG
REPAIR OR REPLACE STEERING ANGLE SENSOR BRANCH WIRE OR CONNECTOR (CANH, CANL)
OK


3.CHECK HARNESS AND CONNECTOR (STEERING ANGLE SENSOR - BATTERY AND BODY GROUND)

  1. Reconnect the cable to the negative (-) battery terminal.

    NOTICE:
    When disconnecting the cable from the negative (-) battery terminal, some systems need to be initialized after the cable is reconnected (Toyota Fortuner RM000002HD2002X.html).


    Toyota Fortuner. Ggn50, 60 Kun51, 61 Tgn51 Lan50.Can Communication.Can Communication System (W/ Vsc).Can Communication System (W/ Vsc) Steering Angle Sensor Communication Stop Mode

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    		Condition
    		Specified Condition
    S23-2 (ESS) - Body ground
    		Always
    		Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    		Switch Condition
    		Specified Condition
    S23-5 (IG) - Body ground
    		Ignition switch ON
    		11 to 14 V
    S23-6 (BAT) - Body ground
    		Always


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE SPIRAL CABLE (STEERING ANGLE SENSOR) (Toyota Fortuner RM000000SS902HX.html)