Dtc C1413 Front Speed Sensor Rh Output Malfunction


DESCRIPTION

WIRING DIAGRAM

INSPECTION PROCEDURE

CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)

READ VALUE USING INTELLIGENT TESTER (FR/FL WHEEL SPEED)

PERFORM TEST MODE (SIGNAL CHECK)

RECONFIRM DTC

CHECK FRONT SPEED SENSOR INSTALLATION

INSPECT FRONT SPEED SENSOR TIP

INSPECT FRONT SKID CONTROL ROTOR

CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - FRONT SPEED SENSOR)

CHECK TERMINAL VOLTAGE (FR+, FL+ TERMINAL)

RECONFIRM DTC

REPLACE FRONT SPEED SENSOR

RECONFIRM DTC

DTC C1413 Front Speed Sensor RH Output Malfunction

DTC C1275 Abnormal Change in Output Signal of Front Speed Sensor RH (Test Mode DTC)

DTC C1276 Abnormal Change in Output Signal of Front Speed Sensor LH (Test Mode DTC)

DTC C1414 Front Speed Sensor LH Output Malfunction


DESCRIPTION

Refer to DTCs C1401 and C1402 (Toyota Fortuner RM000000XI90JJX.html).

DTC Code
DTC Detection Condition
Trouble Area
C1413
C1414
One of the following conditions is met:
  1. An open in the sensor signal circuit occurs 255 times or more.
  2. At a vehicle speed of 20 km/h (12 mph) or more, noise occurs in the sensor signals 75 times or more within 5 seconds.
  3. At a vehicle speed of 10 km/h (6 mph) or more, noise occurs once per rotor rotation for 15 seconds or more.
  1. Front speed sensor RH/LH
  2. Speed sensor circuit
  3. Front skid control rotor RH/LH
  4. Skid control ECU (Brake actuator assembly)
C1275
C1276
Stored during Test Mode.
  1. Front speed sensor RH/LH
  2. Front skid control rotor RH/LH
HINT:
  1. DTCs C1413 and C1275 are for the front speed sensor RH.
  2. DTCs C1414 and C1276 are for the front speed sensor LH.

WIRING DIAGRAM

Refer to DTCs C1405 and C1406 (Toyota Fortuner RM000000XI90JKX.html).

INSPECTION PROCEDURE

NOTICE:
  1. After replacing the brake actuator assembly, perform calibration (Toyota Fortuner RM000000XHR06WX.html).
  2. Check the speed sensor signal after replacement (Toyota Fortuner RM000000XHT08TX.html).
  3. Before disconnecting the connector, make sure that there are no problems with the connection.
  4. After disconnecting the connector, make sure that the connector case and terminals are not deformed or corroded.
1.CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)

  1. Using the intelligent tester, check for any momentary interruption in the wire harness and connector corresponding to the DTC (Toyota Fortuner RM000000XHS0A8X.html).

    ABS/VSC/TRC
    Tester Display
    		Measurement Item/Range
    		Normal Condition
    		Diagnostic Note
    FR Speed Open
    		Front speed sensor RH open circuit detection / Error or Normal
    		Normal
    		-
    FL Speed Open
    		Front speed sensor LH open circuit detection / Error or Normal
    		Normal
    		-
    OK:
    Normal (there are no momentary interruptions).
    HINT:
    Perform the above inspection before removing the sensor or disconnecting a connector.


NG
Go to step 8
OK


2.READ VALUE USING INTELLIGENT TESTER (FR/FL WHEEL SPEED)

  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Start the engine.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Chassis / ABS/VSC/TRC / Data List, and then drive the vehicle.

    ABS/VSC/TRC
    Tester Display
    		Measurement Item/Range
    		Normal Condition
    		Diagnostic Note
    FR Wheel Speed
    		Front speed sensor RH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
    		Actual wheel speed
    		No large fluctuations when driving at a constant speed.
    FL Wheel Speed
    		Front speed sensor LH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
    		Actual wheel speed
    		No large fluctuations when driving at a constant speed.

  1. Check the speed value output from the speed sensor displayed on the intelligent tester.

    HINT:
    Factors that affect the indicated vehicle speed include tire size, tire inflation and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, refer to the reference chart (Toyota Fortuner RM0000011JB00WX.html).
    OK:
    The speed value output from the speed sensor displayed on the intelligent tester is the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).


NG
Go to step 5
OK


3.PERFORM TEST MODE (SIGNAL CHECK)

  1. Perform the signal check in the Test Mode procedure (Toyota Fortuner RM000000XHT08TX.html).

    OK:
    All Test Mode DTCs are cleared.


NG
Go to step 5
OK


4.RECONFIRM DTC

  1. Clear the DTC (Toyota Fortuner RM000000XHV0C7X.html).

  1. Turn the ignition switch off.

  1. Start the engine.

  1. Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.

  1. Check if the same DTC is output (Toyota Fortuner RM000000XHV0C7X.html).

    Result
    Result
    		Proceed to
    DTC is not output
    		A
    DTC is output
    		B
    HINT:
    If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next suspected area (Toyota Fortuner RM000000XHN0BDX.html).


B
REPLACE BRAKE ACTUATOR ASSEMBLY (Toyota Fortuner RM0000010K0010X.html)
A

USE SIMULATION METHOD TO CHECK (Toyota Fortuner RM0000012Q9013X.html)

5.CHECK FRONT SPEED SENSOR INSTALLATION

  1. Turn the ignition switch off.



    Toyota Fortuner. Ggn50, 60 Kun51, 61 Tgn51 Lan50.Brake Control.Vehicle Stability Control System. Dtc C1413 Front Speed Sensor Rh Output Malfunction

  1. Check the speed sensor installation (Toyota Fortuner RM0000010JM029X.html).

    Text in Illustration
    *1
    		Front Speed Sensor
    *a
    		No clearance
    *b
    		CORRECT
    *c
    		INCORRECT
    OK:
    There is no clearance between the sensor and the steering knuckle.
    The installation bolt is tightened properly.


NG
INSTALL FRONT SPEED SENSOR CORRECTLY (Toyota Fortuner RM0000010JM029X.html)
OK


6.INSPECT FRONT SPEED SENSOR TIP

  1. Turn the ignition switch off.

  1. Remove the front speed sensor (Toyota Fortuner RM0000010JP01RX.html).

  1. Check the speed sensor tip.

    OK:
    No scratches, oil or foreign matter on the sensor tip.
    NOTICE:
    Do not replace the speed sensor if no damage to the speed sensor tip is found.
    HINT:
    1. If the sensor is contaminated with oil or other foreign material, clean the sensor.
    2. If there is iron powder sticking to the rotor, this will result in a malfunction. Therefore, confirm that the rotor is not contaminated with foreign material before replacing the sensor.


NG
CLEAN OR REPLACE FRONT SPEED SENSOR
OK


7.INSPECT FRONT SKID CONTROL ROTOR

  1. Turn the ignition switch off.

  1. Remove the front skid control rotor (Toyota Fortuner RM00000112M005X.html).

  1. Check the front skid control rotor.

    OK:
    No scratches, oil or foreign matter on the rotor.


NG
CLEAN OR REPLACE FRONT SKID CONTROL ROTOR
OK


8.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - FRONT SPEED SENSOR)

  1. Turn the ignition switch off.

  1. Disconnect the skid control ECU (brake actuator assembly) connector.

  1. Disconnect the front speed sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for RH
    Tester Connection
    		Condition
    		Specified Condition
    S25-7 (FR+) - S5-1 (FR+)
    		Always
    		Below 1 Ω
    S25-7 (FR+) - Body ground
    		Always
    		10 kΩ or higher
    S25-6 (FR-) - S5-2 (FR-)
    		Always
    		Below 1 Ω
    S25-6 (FR-) - Body ground
    		Always
    		10 kΩ or higher
    for LH:
    Tester Connection
    		Condition
    		Specified Condition
    S25-19 (FL+) - S4-1 (FL+)
    		Always
    		Below 1 Ω
    S25-19 (FL+) - Body ground
    		Always
    		10 kΩ or higher
    S25-18 (FL-) - S4-2 (FL-)
    		Always
    		Below 1 Ω
    S25-18 (FL-) - Body ground
    		Always
    		10 kΩ or higher


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


9.CHECK TERMINAL VOLTAGE (FR+, FL+ TERMINAL)

  1. Turn the ignition switch off.

  1. Connect the skid control ECU (brake actuator assembly) connector.

  1. Disconnect the front speed sensor connector.



    Toyota Fortuner. Ggn50, 60 Kun51, 61 Tgn51 Lan50.Brake Control.Vehicle Stability Control System. Dtc C1413 Front Speed Sensor Rh Output Malfunction

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    for RH
    Tester Connection
    		Switch Condition
    		Specified Condition
    S5-1 (FR+) - Body ground
    		Ignition switch ON
    		8 to 14 V
    for LH
    Tester Connection
    		Switch Condition
    		Specified Condition
    S4-1 (FL+) - Body ground
    		Ignition switch ON
    		8 to 14 V
    Text in Illustration
    *A
    		for RH
    *B
    		for LH
    *a
    		Front view of wire harness connector
    (to Front Speed Sensor)


NG
REPLACE BRAKE ACTUATOR ASSEMBLY (Toyota Fortuner RM0000010K0010X.html)
OK


10.RECONFIRM DTC

  1. Clear the DTCs (Toyota Fortuner RM000000XHV0C7X.html).

  1. Turn the ignition switch off.

  1. Start the engine.

  1. Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.

  1. Check if the same DTC is output (Toyota Fortuner RM000000XHV0C7X.html).

    Result
    Result
    		Proceed to
    DTC is not output
    		A
    DTC is output
    		B


B
Go to step 11
A

USE SIMULATION METHOD TO CHECK (Toyota Fortuner RM0000012Q9013X.html)

11.REPLACE FRONT SPEED SENSOR

  1. Turn the ignition switch off.

  1. Replace the front speed sensor (Toyota Fortuner RM0000010JP01RX.html).


NEXT


12.RECONFIRM DTC

  1. Clear the DTCs (Toyota Fortuner RM000000XHV0C7X.html).

  1. Turn the ignition switch off.

  1. Start the engine.

  1. Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.

  1. Check if the same DTC is output (Toyota Fortuner RM000000XHV0C7X.html).

    Result
    Result
    		Proceed to
    DTC is not output
    		A
    DTC is output
    		B


B
REPLACE FRONT SKID CONTROL ROTOR (Toyota Fortuner RM00000112M005X.html)
A

END