Automatic Transmission System Diagnosis System
DESCRIPTION
NORMAL MODE AND CHECK MODE
2 TRIP DETECTION LOGIC
FREEZE FRAME DATA
CHECK DLC3
CHECK MIL
Automatic Transmission System -- Diagnosis System |
When troubleshooting Multiplex OBD (M-OBD) vehicles, the vehicle must be connected to the intelligent tester. Various data output from the vehicle's ECM can then be read.
The Malfunction Indicator Lamp (MIL) illuminates when the vehicle's on-board computer detects a malfunction in the computer itself or in drive system components. In addition, the applicable Diagnostic Trouble Codes (DTCs) are recorded in the ECM memory (Toyota Fortuner RM000000W710JJX.html).
When the malfunction does not reoccur, the MIL stays illuminated until the ignition switch is turned OFF, and the MIL turns OFF when the engine is started. However, the DTCs remain recorded in the ECM memory.
To check DTCs, connect the tester to the Data Link Connector 3 (DLC3) on the vehicle or connect terminals TC and CG on the DLC3 (DTCs will be displayed on the combination meter).
| NORMAL MODE AND CHECK MODE |
The diagnosis system operates in "normal mode" during normal vehicle use. In normal mode, "2 trip detection logic" is used to ensure accurate detection of malfunctions. "Check mode" is also available to technicians as an option. In check mode, "1 trip detection logic" is used for simulating malfunction symptoms and increasing the system's ability to detect malfunctions, including intermittent malfunctions (Toyota Fortuner RM000000W780AUX.html).
When a malfunction is first detected, the malfunction is temporarily stored in the ECM memory (1st trip). If the same malfunction is detected during the next drive cycle, the MIL is illuminated (2nd trip).
Freeze frame data records the engine conditions (fuel system, calculated engine load, engine coolant temperature, fuel trim, engine speed, vehicle speed, etc.) when a malfunction is detected. When troubleshooting, freeze frame data can help determine if the vehicle was running or stopped, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
The tester records freeze frame data in 5 different instances: 1) 3 times before the DTC is set, 2) once when the DTC is set, and 3) once after the DTC is set. These data can be used to simulate the vehicle's condition around the time when the malfunction occurred. The data may help find the cause of the malfunction, or help in judging if the DTC is being caused by a temporary malfunction or not.
|
The vehicle's ECM uses ISO 14230 (M-OBD) communication protocol. The terminal arrangement of the DLC3 complies with ISO 15031-03 and matches the ISO 14230 format.
If the result is not as specified, the DLC3 may have a malfunction. Repair or replace the harness and connector.
Symbols (Terminal No.)
| Terminal Description
| Condition
| Specified Condition
|
SIL (7) - SG (5)
| Bus "+" line
| During transmission
| Pulse generation
|
CG (4) - Body ground
| Chassis ground
| Always
| Below 1 Ω
|
SG (5) - Body ground
| Signal ground
| Always
| Below 1 Ω
|
BAT (16) - Body ground
| Battery positive
| Always
| 9 to 14 V
|
- HINT:
- Connect the cable of the tester to the DLC3, turn the ignition switch ON and attempt to use the tester. If the display indicates that a communication error has occurred, there is a problem either with the vehicle or with the tester.
- If communication is normal when the tester is connected to another vehicle, inspect the DLC3 on the original vehicle.
- If communication is still not possible when the tester is connected to another vehicle, the problem is probably in the tester itself. Consult the Service Department listed in the tester's instruction manual.
The MIL illuminates when the ignition switch is turned ON and the engine is not running.
If the MIL is not illuminated, check the MIL circuit (Toyota Fortuner RM000000WZ10LRX.html).
When the engine is started, check that the MIL turns OFF.
If the MIL remains illuminated, the diagnosis system has detected a malfunction or abnormality in the system.
