Fan Installation

Install the fan to the coupling with the 4 nuts.

Torque:

6.5 N*m{66 kgf*cm, 58 in.*lbf}

Install the fan pulley to the water pump.

Install the shroud together with the coupling fan between the radiator and engine.

NOTICE:

Be careful not to damage the radiator core.

Install the fluid coupling fan to the fan pulley with the 4 nuts.

HINT:

Tighten the nuts as much as possible by hand.

Attach the shroud's claws to the radiator as shown in A in the illustration.

Install the shroud with the 2 bolts.

Torque:

5.0 N*m{51 kgf*cm, 44 in.*lbf}

Install the fan and generator V belt, cooler compressor V belt and vane pump V belt (Toyota Fortuner RM00000122V002X.html).

Tighten the 4 nuts of the fluid coupling fan.

Torque:

19 N*m{194 kgf*cm, 14 ft.*lbf}

Install the radiator reservoir with the bolt.

Torque:

5.0 N*m{51 kgf*cm, 44 in.*lbf}

Connect the No. 1 and No. 2 water by-pass hoses to the tank upper and lower.

Install the oil reservoir with the 3 bolts.

Torque:

5.0 N*m{51 kgf*cm, 44 in.*lbf}

Tighten the radiator drain cock plug by hand.

Tighten the cylinder block drain cock plug.

Torque:

57 N*m{581 kgf*cm, 42 ft.*lbf}

Fill the radiator with TOYOTA Super Long Life Coolant (SLLC) to the reservoir tank's FULL line.

Standard capacity:

9.4 liters (9.9 US qts, 8.3 Imp. qts)

HINT:

1. TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).
   

1. Please contact your TOYOTA dealer for further details.
   

NOTICE:

Never use water as a substitute for engine coolant.

Press the inlet and outlet radiator hoses several times by hand, and then check the level of the coolant.
If the coolant level drops below the LOW line, add TOYOTA SLLC to the FULL line.

Install the radiator reservoir cap.

Using a wrench, install the vent plug.

Torque:

2.0 N*m{20 kgf*cm, 18 in.*lbf}

Bleed air from the cooling system.

1. Warm up the engine until the thermostat opens. While the thermostat is open, circulate the coolant for several minutes.
   

2. Maintain the engine speed at 2,500 to 3,000 rpm.
   

3. Press the inlet and outlet radiator hoses several times by hand to bleed air.
   

   CAUTION:

   When pressing the radiator hoses:

   1. Wear protective gloves.
      
   1. Be careful as the radiator hoses are hot.
      
   1. Keep your hands away from the radiator fan.
      

4. Stop the engine and wait until the coolant cools down to ambient temperature.
   

   CAUTION:

   Do not remove the radiator reservoir cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

After the coolant cools down, check that the coolant level is at the FULL line.
If the coolant level is below the LOW line, add TOYOTA SLLC to the FULL line.

Check for engine coolant leaks (Toyota Fortuner RM000001443007X_01_0001.html).

Install the under cover with the 8 bolts.

Torque:

28 N*m{286 kgf*cm, 21 ft.*lbf}