Sfi System -- Data List / Active Test |
| READ DATA LIST |
- HINT:
- Using the intelligent tester's Data List allows switch, sensor, actuator, and other item values to be read without removing any parts. Reading the Data List early in troubleshooting is one way to save time.
- NOTICE:
- In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Warm up the engine.
Turn the ignition switch OFF.
Connect the intelligent tester to the DLC3.
Turn the ignition switch ON.
Turn the tester ON.
Enter the following menus: Powertrain / Engine and ECT / Data List.
- HINT:
- To display the entire Data List, press the pull down menu button next to Primary. Then select All Data.
Read the Data List on the tester's screen.
 |
| Intelligent Tester Display | Measurement Item: Display (Range) | Normal Condition *1 | Diagnostic Note |
| Injector | Injection period of No. 1 cylinder: Min.: 0 ms, Max.: 32.64 ms | 1.3 to 2.8 ms: Idling | - |
| IGN Advance | Ignition timing advance for No. 1 cylinder: Min.: -64°, Max.: 63.5° | BTDC 7 to 24°: Idling (A/C OFF, shift position N) | - |
| Calculated Load | Calculated load by ECM: Min.: 0%, Max.: 100% | 11.4 to 16.4%: idle (A/C OFF and shift position N) 13.1 to 18.9%: 2,500 rpm (A/C OFF and shift position N) | - |
| MAF | Air flow rate from MAF meter: Min.: 0 g/sec., Max.: 655 g/sec. | 3.2 to 4.7 g/sec.: idling 13.1 to 18.9 g/sec.: 2,500 rpm | If value approximately 0.0 g/sec.:
|
| Engine Speed | Engine speed: Min.: 0 rpm, Max.: 16,383 rpm | 650 to 750 rpm: Idle after engine warmed up | - |
| Vehicle Speed | Vehicle speed: Min.: 0 km/h, Max.: 255 km/h | Actual vehicle load | Same as speedometer indication |
| Coolant Temp | Engine coolant temperature: Min.: -40°C, Max.: 140°C | 80 to 95°C (167 to 203°F): engine warmed up |
|
| Intake Air | Intake air temperature: Min.: -40°C, Max.: 140°C | Equivalent to ambient air temperature |
|
| Air-Fuel Ratio | Air-fuel ratio: Min.: 0, Max.: 1.999 | 0.8 to 1.2: During idling | - |
| Purge Density Learn Value | Learning value of purge density: Min.: -50, Max.: 350 | - 40 to 0%: Idling | Service data |
| Purge Flow | Purge flow: Min.: 0%, Max.: 102.4% | 0 to 100%: Idling | - |
| Knock Correction Learn Value | Correction learning value of knocking: Min.: -64 crankshaft angle, Max.: 1,984 crankshaft angle | 0 to 22 crankshaft angle: Driving, 70 km/h (44 mph) | Service data |
| Knock Feedback Value | Feedback value of knocking: Min.: -64 crankshaft angle, Max.: 1,984 crankshaft angle | -22 to 0 crankshaft angle: Driving, 70 km/h (44 mph) | Service data |
| Clutch Current | Clutch current: Min.: 0 A, Max.: 2.49 A | - | - |
| Electromagnetic Clutch | Electromagnetic clutch: ON or OFF | - | - |
| Accelerator Position No. 1 | No. 1 absolute accelerator pedal position: Min.: 0%, Max.: 100% | 10 to 22%: accelerator pedal released 54 to 86%: accelerator pedal fully depressed | - |
| Accelerator Position No. 2 | No. 2 absolute accelerator pedal position: Min.: 0%, Max.: 100% | 12 to 42%: accelerator pedal released 66 to 98%: accelerator pedal fully depressed | - |
| Accelerator Position No. 1 | No. 1 absolute accelerator pedal position sensor voltage: Min.: 0 V, Max.: 4.98 V | - | ETCS freeze frame data |
| Accelerator Position No. 2 | No. 2 absolute accelerator pedal position sensor voltage: Min.: 0 V, Max.: 4.98 V | - | ETCS freeze frame data |
| Accelerator Position No. 1 | No. 1 accelerator pedal position sensor voltage: Min.: 0 V, Max.: 5 V | 0.4 to 1.4 V: Accelerator pedal released 3.1 to 4.6 V: Accelerator pedal fully depressed | - |
| Accelerator Position No. 2 | No. 2 accelerator pedal position sensor voltage: Min.: 0 V, Max.: 5 V | 1.0 to 2.2 V: Accelerator pedal released 3.9 to 5.0 V: Accelerator pedal fully depressed | - |
| Accelerator Idle Position | Whether or not accelerator pedal position sensor detecting idle: ON or OFF | ON: Idling | - |
| Throttle Fully Close Learn | No. 1 throttle valve fully closed (learned value): Min.: 0 V, Max.: 5 V | 0.4 to 0.8 V | - |
| Accel Fully Close #1 (AD) | Accelerator fully closed value (AD): Min.: 0 V, Max.: 4.98 V | - | ETCS service data |
| Accel Fully Close Learn #1 | No. 1 accelerator fully closed learning value: Min.: 0, Max.: 124.512 | - | ETCS service data |
| Accel Fully Close Learn #2 | No. 2 accelerator fully closed learning value: Min.: 0, Max.: 124.512 | - | ETCS service data |
| Fail Safe Drive | Whether or not fail-safe function executed: ON or OFF | ON: ETCS has failed | - |
| Fail Safe Drive (Main CPU) | Whether or not fail-safe function executed: ON or OFF | ON: ETCS has failed | - |
| ST1 | Brake pedal: ON or OFF | ON: Released OFF: Depressed | - |
| System Guard | System guard: ON or OFF | - | - |
| Open Side Malfunction | Open side malfunction: ON or OFF | - | ETCS service data |
| Throttle Position | Absolute throttle position sensor: Min.: 0%, Max.: 100% | 10 to 24%: throttle fully closed 64 to 96%: throttle fully open | - |
| Throttle Idle Position | Whether or not throttle position sensor detecting idle: ON or OFF | ON: Idling | - |
| Throttle Require Position | Throttle requirement position: Min.: 0 V, Max.: 5 V | 0.5 to 1.0 V: Idling | - |
| Throttle Sensor Position | Throttle sensor positioning: 0 to 100% | 0 to 10%: throttle fully closed 64 to 96%: throttle fully open | - |
| Throttle Sensor Position #2 | No. 2 absolute throttle position: 0 to 100% | 10 to 24%: throttle fully closed 64 to 96%: throttle fully open | - |
| Throttle Position No. 1 | No. 1 throttle position sensor output voltage: Min.: 0 V, Max.: 4.98 V | - | ETCS freeze frame data |
| Throttle Position No. 2 | No. 2 throttle position sensor output voltage: Min.: 0 V, Max.: 4.98 V | - | ETCS freeze frame data |
| Throttle Position No. 1 | No. 1 throttle position: Min.: 0 V, Max.: 5 V | 0.4 to 1. 4 V: Throttle fully closed 3.1 to 4.6 V: Throttle fully open | - |
| Throttle Position No. 2 | No. 2 throttle position: Min.: 0 V, Max.: 5 V | 1.0 to 2.2 V: Throttle fully closed 3.9 to 5.0 V: Throttle fully open | - |
| Throttle Position Command | No. 1 throttle position command value: Min.: 0 V, Max.: 4.98 V | 0.5 to 4.8 V | ETCS service data |
| Throttle Sens Open Pos #1 | Throttle sensor opener position : Min.: 0 V, Max.: 4.98 V | 0.6 to 1.0 V | ETCS service data |
| Throttle Sens Open Pos #2 | No. 2 throttle sensor opener position: Min.: 0 V, Max.: 4.98 V | 2.0 to 2.6 V | ETCS service data |
| Throttle Sens Open #1 (AD) | No. 1 Throttle sensor opener position (AD): Min.: 0 V, Max.: 4.98 V | 0.6 to 0.9 V | ETCS service data |
| Throttle Motor | Whether or not throttle motor control permitted: ON or OFF | ON: Idling | Read value with ignition switch ON (do not start engine) |
| Throttle Motor Current | Throttle actuator current: Min.: 0 A, Max.: 80 A | 0 to 3.0 A: Idling | - |
| Throttle Motor | Throttle actuator: Min.: 0%, Max.: 100% | 0.5 to 40%: Idling | - |
| Throttle Motor Current | Throttle actuator current: Min.: 0 A, Max.: 19.92 A | 0 to 3.0 A: Idling | - |
| Throttle Motor Open Duty | Throttle motor opening duty ratio: Min.: 0%, Max.: 100% | 0 to 40%: During idling | When accelerator pedal depressed, duty ratio increased |
| Throttle Motor Close Duty | Throttle actuator closed duty ratio: Min.: 0%, Max.: 100% | 0 to 40%: During idling | When accelerator pedal released quickly, duty ratio increased |
| Throttle Motor Duty (Open) | Throttle actuator duty ratio (open): Min.: 0%, Max.: 100% | - | ETCS service data |
| Throttle Motor Duty (Close) | Throttle actuator duty ratio (close): Min.: 0%, Max.: 100% | - | ETCS service data |
| O2S B1 S2 | Heated oxygen sensor output voltage for bank 1 sensor 2: Min.: 0 V, Max.: 1.275 V | 0.1 to 0.9 V: Driving 70 km/h (44 mph) | Performing Control the Injection Volume or Control the Injection Volume for A/F sensor function of Active Test enables technician to check output voltage of sensor |
| O2S B2 S2 | Heated oxygen sensor output voltage for bank 2 sensor 2: Min.: 0 V, Max.: 1.275 V | 0.1 to 0.9 V: Driving 70 km/h (44 mph) | Performing Control the Injection Volume or Control the Injection Volume for A/F sensor function of Active Test enables technician to check output voltage of sensor |
| AFS B1 S1 | A/F sensor output voltage for bank 1 sensor 1: Min.: 0 V, Max.: 7.999 V | 2.8 to 3.8 V: Idling | Performing Control the Injection Volume or Control the Injection Volume for A/F sensor function of Active Test enables technician to check output voltage of sensor |
| AFS B2 S1 | A/F sensor output voltage for bank 2 sensor 1: Min.: 0 V, Max.: 7.999 V | 2.8 to 3.8 V: Idling | Performing Control the Injection Volume or Control the Injection Volume for A/F sensor function of Active Test enables technician to check output voltage of sensor |
| Total FT #1 | Total fuel trim (bank 1): Min.: 0.5, Max.: 0.498 | 0.5 to 1.4 at idle | Below 1.0: Fuel trim is lean 1.0 or more: Fuel trim is rich |
| Total FT #2 | Total fuel trim (bank 2): Min.: 0.5, Max.: 0.498 | 0.5 to 1.4 at idle | Below 1.0: Fuel trim is lean 1.0 or more: Fuel trim is rich |
| Short FT #1 | Short-term fuel trim of bank 1: Min.: -100%, Max.: 99.2% | 0 +-20% | Short-term fuel compensation used to maintain air-fuel ratio at stoichiometric air-fuel ratio |
| Long FT #1 | Long-term fuel trim of bank 1: Min.: -100%, Max.: 99.2% | 0 +-20% | Overall fuel compensation carried out in long-term to compensate continual deviation of short-term fuel trim from central value |
| Short FT #2 | Short-term fuel trim of bank 2: Min.: -100%, Max.: 99.2% | 0 +-20% | Short-term fuel compensation used to maintain air-fuel ratio at stoichiometric air-fuel ratio |
| Long FT #2 | Long-term fuel trim of bank 1: Min.: -100%, Max.: 99.2% | 0 +-20% | Overall fuel compensation carried out in long-term to compensate continual deviation of short-term fuel trim from central value |
| Fuel System Status (Bank 1) | Fuel system status (Bank 1): OL, CL, OL DRIVE, OL FAULT, CL FAULT | CL: Idling after engine warmed up |
|
| Fuel System Status (Bank 2) | Fuel system status (Bank 2): OL, CL, OL DRIVE, OL FAULT, CL FAULT | CL: Idling after engine warmed up |
|
| O2FT B1 S2 | Short-term fuel trim associated with bank 1 sensor 2: Min.: -100%, Max.: 99.2% | - | Same as Short FT #1 |
| O2FT B2 S2 | Short-term fuel trim associated with bank 2 sensor 2: Min.: -100%, Max.: 99.2% | - | Same as Short FT #2 |
| AF FT B1 S1 | Short-term fuel trim associated with bank 1 sensor 1: Min.: 0, Max.: 1.999 |
| - |
| AF FT B2 S1 | Short-term fuel trim associated with bank 2 sensor 1: Min.: 0, Max.: 1.999 |
| - |
| Initial Engine Coolant Temp | Initial engine coolant temperature: Min.: -40°C, Max.: 120°C | Coolant temperature when engine started | Service data |
| Initial Intake Air Temp | Initial intake air temperature: Min.: -40°C, Max.: 120°C | Intake air temperature when engine started | Service data |
| Injection Volum (Cylinder 1) | Injection volume (cylinder 1): Min.: 0 ml, Max.: 2.048 ml | 0 to 0.5 ml | Quantity of fuel injection volume for 10 times |
| SPD (SP2) | Output shaft speed: Min.: 0 km/h, Max.: 255 km/h | - | For automatic transmission |
| SPD (NT) | Input shaft speed: Min.: 0 rpm, Max.: 12,750 rpm | - | For automatic transmission |
| Starter Signal | Starter signal: ON or OFF | ON: Cranking | - |
| Power Steering Switch | Power steering signal: ON or OFF | ON: Power steering operation | - |
| Power Steering Signal | Power steering signal: ON or OFF | ON: When steering wheel first turned after ignition switch turned ON | This signals status usually ON until ignition switch turned OFF |
| Closed Throttle Position SW | Closed throttle position switch: ON or OFF | ON: Throttle fully closed OFF: Throttle open | - |
| A/C Signal | A/C signal: ON or OFF | ON: A/C ON | - |
| Neutral Position SW Signal | PNP switch: ON or OFF | ON: Shift position is P or N | For automatic transmission |
| Electrical Load Signal | Electrical load signal: ON or OFF | ON: Headlights or defogger turned ON | - |
| Stop Light Switch | Stop light switch: ON or OFF | ON: Brake pedal depressed | - |
| ETCS Actuator Power | Whether or not electric throttle control system power inputted: ON or OFF | ON: Idling | - |
| +BM Voltage | +BM voltage: Min.: 0, Max.: 19.92 | 10 to 15 V: Idling | ETCS service data |
| Battery Voltage | Battery voltage: Min.: 0 V, Max.: 65.535 V | 9 to 14 V: Idling | - |
| Actuator Power Supply | Actuator power supply ON or OFF | ON: Idling | ETCS service data |
| Variable Intake Control VSV | VSV status for ACIS control: ON or OFF | - | Active Test support data |
| ACT VSV | A/C cut status for Active Test: ON or OFF | - | Active Test support data |
| VVT Control Status (Bank 2) | VVT control (bank 2) status: ON or OFF | - | Active Test support data |
| EVAP Purge VSV | VSV status for EVAP control: ON or OFF | - | Active Test support data |
| Fuel Pump/Speed Status | Fuel pump/speed status: ON or OFF | - | Active Test support data |
| VVT Control Status (Bank 1) | VVT control (bank 1) status: ON or OFF | - | Active Test support data |
| TC and TE1 | TC and TE1 terminal of DLC3: ON or OFF | - | Active Test support data |
| VVT Aim Angle (Bank 1) *2 | VVT aim angle (bank 1): Min.: 0%, Max.: 100% | 0%: Idling | VVT duty signal value during intrusive operation |
| VVT Change Angle (Bank 1) *2 | VVT change angle: Min.: 0°FR, Max.: 60°FR | 0 to 5°FR: Idling | Displacement angle during intrusive operation |
| VVT OCV Duty (Bank 1) *2 | VVT OCV operation duty: Min.: 0%, Max.: 100% | 0%: Idling | Requested duty value for intrusive operation |
| VVT Aim Angle (Bank 2) *2 | VVT aim angle (bank 2): Min.: 0%, Max.: 100% | 0%: Idling | VVT duty signal value during intrusive operation |
| VVT Change Angle (Bank 2) *2 | VVT change angle (bank 2): Min.: 0°FR, Max.: 60°FR | 0 to 5°FR: Idling | Displacement angle during intrusive operation |
| VVT OCV Duty (Bank 2) *2 | VVT OCV (bank 2) operation duty: Min.: 0%, Max.: 100% | 0%: Idling | Requested duty value for intrusive operation |
| Idle Fuel Cut | Fuel cut idle: ON or OFF | ON: Fuel cut operation | Idle fuel cut: ON when throttle valve fully closed and engine speed over 2,800 rpm |
| FC TAU | Fuel cut TAU: Fuel cut during very light load: ON or OFF | ON: Fuel cut operating | Fuel cut being performed under very light load to prevent engine combustion from becoming incomplete |
| # Codes | # Codes: Min.: 0, Max.: 255 | - | Number of detected DTCs |
| Check Mode | Check mode: 0: OFF, 1: ON | ON: Check mode ON | Toyota Fortuner RM0000010E7004X.html |
| SPD Test | Check mode result for vehicle speed sensor: 0: COMPL, 1: INCMPL | - | - |
| Misfire Test | Check mode result for misfire monitor: 0: COMPL, 1: INCMPL | - | - |
| OXS2 Test | Check mode result for heated oxygen sensor (bank 2): 0: COMPL, 1: INCMPL | - | - |
| OXS1 Test | Check mode result for heated oxygen sensor (bank 1): 0: COMPL, 1: INCMPL | - | - |
| A/F Test Results (Bank 2) | Check mode result for air-fuel ratio sensor (bank 2): 0: COMPL, 1: INCMPL | - | - |
| A/F Test Results (Bank 1) | Check mode result for air-fuel ratio sensor (bank 1): 0: COMPL, 1: INCMPL | - | - |
| MIL ON Run Distance | MIL ON run distance: Min.: 0 km, Max.: 65,535 km | Distance after DTC detected | - |
| Running Time From MIL ON | Running time from MIL ON: Min.: 0 minutes, Max.: 65,535 minutes | Equivalent to running time after MIL ON | - |
| Engine Run Time | Engine run time: Min.: 0 seconds, Max.: 65,535 seconds | Time after engine start | Service data |
| Time After DTC Cleared | Time after DTC cleared: Min.: 0 minutes, Max.: 65,535 minutes | Equivalent to time after DTCs erased | - |
| Distance from DTC Cleared | Distance after DTC cleared: Min.: 0 km, Max.: 65.535 km | Equivalent to drive distance after DTCs erased | - |
| Warmup Cycle Cleared DTC | Warm up cycle after DTC cleared: Min.: 0, Max.: 225 | - | Number of warm up cycles after DTC cleared |
| Model Code | Model code | - | Identifying the model code: GGN2# |
| Engine Type | Engine type | - | Identifying the engine type: 1GR-FE |
| Cylinder Number | Number of cylinders: Min.: 0, Max.: 255 | - | Identifying the number of cylinders: 6 |
| Destination | Destination | - | Identifying destination: A (America) |
| Model Year | Model year: Min.: 1900, Max.: 2155 | - | Identifying model year: 200# |
- HINT:
- *1: If no conditions are specifically stated for "Idling", it means the shift lever is on N or P, the A/C switch is OFF and all accessory switches are OFF.
- *2: Data List values are only displayed when performing the following Active Tests: VVT B1, VVT B2, VVT EX B1 and VVT EX B2. For other Active Tests, the Data List value will be 0.
| PERFORM ACTIVE TEST |
- HINT:
- Performing the intelligent tester's Active Test allows relay, VSV, actuator and other items to be operated without removing any parts. Performing the Active Test early in troubleshooting is one way to save time.
- The Data List can be displayed during the Active Test.
Warm up the engine.
Turn the ignition switch OFF.
Connect the intelligent tester to the DLC3.
Turn the ignition switch ON.
Turn the tester ON.
Enter the following menus: Powertrain / Engine and ECT / Active Test.
According to the display on the tester, perform the Active Test.
| Intelligent Tester Display | Test Details | Control Range | Diagnostic Note |
| Control the Injection Volume | Change injection volume | -12.5 to 24.8% |
|
| Activate the Fuel Pump Speed Control | Fuel pump speed control | ON (low speed)/OFF (high speed) | - |
| Activate the VSV for Intake Control | VSV for ACIS | ON/OFF | - |
| Activate the VSV for EVAP Control | Purge VSV | ON/OFF | - |
| Active the VVT System (Bank 1) | Turn on and off Oil Control Valve (OCV) | ON/OFF |
|
| Control the VVT System (Bank 2) | Turn on and off OCV | ON/OFF |
|
| Control the A/C Cut Signal | Control the A/C cut signal | ON/OFF | - |
| Control the Fuel Pump/Speed | Fuel pump | ON/OFF | - |
| Connect the TC and TE1 | Turn on and off TC and TE1 connection | ON/OFF | ON: TC and TE1 connected OFF: TC and TE1 disconnected |
| Control the Idle Fuel Cut Prohibit | Prohibit idling fuel cut control | ON/OFF | - |
| Control the ETCS Open/Close Slow Speed | Throttle actuator | ON: Throttle valve opens slowly | This test is possible when the following conditions are met:
|
| Control the ETCS Open/Close Fast Speed | Throttle actuator | ON: Throttle valve opens fast | Same as above |
| Control the Cylinder#1 Fuel Cut | Cylinder #1 injector fuel cut | ON/OFF | This test is possible during vehicle stopping and engine idling |
| Control the Cylinder#2 Fuel Cut | Cylinder #2 injector fuel cut | ON/OFF | Same as above |
| Control the Cylinder#3 Fuel Cut | Cylinder #3 injector fuel cut | ON/OFF | Same as above |
| Control the Cylinder#4 Fuel Cut | Cylinder #4 injector fuel cut | ON/OFF | Same as above |
| Control the Cylinder#5 Fuel Cut | Cylinder #5 injector fuel cut | ON/OFF | Same as above |
| Control the Cylinder#6 Fuel Cut | Cylinder #6 injector fuel cut | ON/OFF | Same as above |
| Control the VVT Linear (Bank 1) | Control the VVT (bank 1) | -128 to 127% This valve added to present OCV control duty 100%: Maximum advance -100%: Maximum retard | Engine stalls or rough idles when the VVT actuator is operated at 100% This test is possible during idle |
| Control the VVT Linear (Bank 2) | Control the VVT (bank 2) | -128 to 127% This valve added to present OCV control duty 100%: Maximum advance -100%: Maximum retard | Engine stalls or rough idles when the VVT actuator is operated at 100% This test is possible during idle |