Headlight Assembly (For Hid Headlight) - Reassembly

Land Cruiser URJ200 URJ202 GRJ200 VDJ200 - LIGHTING EXT

HEADLIGHT ASSEMBLY (for HID Headlight) - REASSEMBLY

  • HINT:
Use the same procedure for the RH and LH sides.
The procedure listed below is for the LH side.
1. INSTALL HEADLIGHT LEVELING MOTOR LH

Type 1:

Headlight Assembly (For Hid Headlight) - Reassembly. LIGHTING EXT. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Insert the headlight leveling motor LH in the direction indicated by the arrow (1) in the illustration.

Turn the aiming screw in the direction indicated by the arrow (2) in the illustration to connect the shaft.

Turn the headlight leveling motor LH in the direction indicated by the arrow (3) in the illustration to install it.

Connect the connector.

Type 2:

Headlight Assembly (For Hid Headlight) - Reassembly. LIGHTING EXT. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Attach the tip of the headlight leveling motor LH with the reflector as shown in the illustration.

Headlight Assembly (For Hid Headlight) - Reassembly. LIGHTING EXT. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Turn the headlight leveling motor LH in the direction indicated by the arrow in the illustration to install the headlight leveling motor LH.

  • HINT:
  • For the headlight leveling motor RH, rotate it in the opposite direction of the arrow shown in the illustration before pulling it out.
2. INSTALL FRONT TURN SIGNAL LIGHT BULB
Headlight Assembly (For Hid Headlight) - Reassembly. LIGHTING EXT. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Install the front turn signal light bulb to the socket.

Turn the socket in the direction indicated by the arrow in the illustration to install the socket.

3. INSTALL NO. 1 HEADLIGHT BULB
Headlight Assembly (For Hid Headlight) - Reassembly. LIGHTING EXT. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Turn the No. 1 headlight bulb in the direction indicated by the arrow in the illustration to install the No. 1 headlight bulb.

  • NOTICE:
  • Do not touch the glass port of the No. 1 headlight bulb.

Connect the connector.

4. INSTALL DISCHARGE HEADLIGHT BULB
Headlight Assembly (For Hid Headlight) - Reassembly. LIGHTING EXT. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Install the discharge headlight bulb and lock the set spring as shown in the illustration.

  • NOTICE:
  • Do not touch the glass port of the discharge headlight bulb.
5. INSTALL HEADLIGHT GASKET

Install a new headlight gasket to the headlight light control ECU sub-assembly LH.

6. INSTALL HEADLIGHT LIGHT CONTROL ECU SUB-ASSEMBLY LH
Headlight Assembly (For Hid Headlight) - Reassembly. LIGHTING EXT. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Turn the headlight light control ECU sub-assembly LH socket in the direction indicated by the arrow in the illustration to connect the headlight light control ECU sub-assembly LH socket.

  • NOTICE:
Check that the headlight gasket is installed on the headlight light control ECU subassembly LH.
Check that the headlight gasket is not damaged or contaminated with foreign matter. If there is any damage, replace the headlight gasket with a new one.
Do not pull the headlight light control ECU sub-assembly LH with the socket connected.
Headlight Assembly (For Hid Headlight) - Reassembly. LIGHTING EXT. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Turn the headlight light control ECU sub-assembly LH in the direction indicated by the arrow in the illustration to install the headlight light control ECU sub-assembly to the headlight unit.

Connect the connector.