Lighting System - Door Courtesy Light Circuit

Land Cruiser URJ200 URJ202 GRJ200 VDJ200 - LIGHTING EXT

DESCRIPTION

WIRING DIAGRAM

INSPECTION PROCEDURE

CHECK OPERATION OF DOOR COURTESY LIGHT

INSPECT FUSE (DOME1)

CHECK HARNESS AND CONNECTOR (DOOR COURTESY LIGHT - BODY GROUND)

INSPECT DOOR COURTESY LIGHT (FRONT DOOR LH)

CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BODY GROUND)

INSPECT DOOR COURTESY LIGHT (FRONT DOOR RH)

CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BODY GROUND)

INSPECT COURTESY LIGHT (REAR DOOR LH)

CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BODY GROUND)

INSPECT DOOR COURTESY LIGHT (REAR DOOR RH)

CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BODY GROUND)

LIGHTING SYSTEM - Door Courtesy Light Circuit

DESCRIPTION

The door courtesy light turns on when the door is opened and turns off when closed.


WIRING DIAGRAM

Lighting System - Door Courtesy Light Circuit. LIGHTING EXT. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

INSPECTION PROCEDURE

1.CHECK OPERATION OF DOOR COURTESY LIGHT

When a door is opened, check that the following lights do not illuminate.

Result
ResultProceed to
All door courtesy light does not illuminateA
Front door courtesy light LH does not illuminateB
Front door courtesy light RH does not illuminateC
Rear door courtesy light LH does not illuminateD
Rear door courtesy light RH does not illuminateE
B
Go to step 4
C
Go to step 6
D
Go to step 8
E
Go to step 10
A
2.INSPECT FUSE (DOME1)

Remove the DOME1 fuse from the engine room junction block.

Measure the resistance according to the value(s) in the table below.

  • Standard Resistance:
  • Tester ConnectionConditionSpecified Condition
    DOME1 fuseAlwaysBelow 1 Ω
NG
REPLACE FUSE
OK
3.CHECK HARNESS AND CONNECTOR (DOOR COURTESY LIGHT - BODY GROUND)
Lighting System - Door Courtesy Light Circuit. LIGHTING EXT. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Disconnect the I13, I5, J12 and J5 ECU connectors.

Measure the voltage according to the value(s) in the table below.

  • Standard Voltage:
  • Tester ConnectionSwitch ConditionSpecified Condition
    I13-1 - Body groundAlways11 to 14 V
    J12-1 - Body ground
    I5-1 - Body ground
    J5-1 - Body ground
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
PROCEED TO NEXT INSPECTION PROCEDURE SHOWN IN PROBLEM SYMPTOMS TABLE ()
4.INSPECT DOOR COURTESY LIGHT (FRONT DOOR LH)
Lighting System - Door Courtesy Light Circuit. LIGHTING EXT. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Remove the door courtesy light connector.

Check that the door courtesy light comes on.

  • OK:
  • Measurement ConditionSpecified Condition
    Battery positive (+) - Terminal 2
    Battery positive (-) - Terminal 1    		Light illumination
NG
Go to step 5
OK
END
5.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BODY GROUND)
Lighting System - Door Courtesy Light Circuit. LIGHTING EXT. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Remove the main body ECU.

for LHD:


Measure the voltage according to the value(s) in the table below.

  • Standard Voltage:
  • Tester ConnectionConditionSpecified Condition
    E1-24 (DCTY) - Body groundAlways11 to 14V

for RHD:


Measure the voltage according to the value(s) in the table below.

  • Standard Voltage:
  • Tester ConnectionConditionSpecified Condition
    E2-21 (PCTY) - Body groundAlways11 to 14V
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
REPLACE MAIN BODY ECU
6.INSPECT DOOR COURTESY LIGHT (FRONT DOOR RH)
Lighting System - Door Courtesy Light Circuit. LIGHTING EXT. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Remove the door courtesy light connector.

Check that the door courtesy light comes on.

  • OK:
  • Measurement ConditionSpecified Condition
    Battery positive (+) - Terminal 2
    Battery positive (-) - Terminal 1    		Light illumination
NG
Go to step 7
OK
END
7.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BODY GROUND)
Lighting System - Door Courtesy Light Circuit. LIGHTING EXT. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Remove the main body ECU.

for LHD:


Measure the voltage according to the value(s) in the table below.

  • Standard Voltage:
  • Tester ConnectionConditionSpecified Condition
    E2-21 (PCTY) - Body groundAlways11 to 14V

for RHD:


Measure the voltage according to the value(s) in the table below.

  • Standard Voltage:
  • Tester ConnectionConditionSpecified Condition
    E1-24 (DCTY) - Body groundAlways11 to 14V
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
REPLACE MAIN BODY ECU
8.INSPECT COURTESY LIGHT (REAR DOOR LH)
Lighting System - Door Courtesy Light Circuit. LIGHTING EXT. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Remove the door courtesy light connector.

Check that the door courtesy light comes on.

  • OK:
  • Measurement ConditionSpecified Condition
    Battery positive (+) - Terminal 2
    Battery positive (-) - Terminal 1    		Light illumination
NG
Go to step 9
OK
END
9.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BODY GROUND)
Lighting System - Door Courtesy Light Circuit. LIGHTING EXT. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Remove the main body ECU.

Measure the voltage according to the value(s) in the table below.

  • Standard Voltage:
  • Tester ConnectionConditionSpecified Condition
    2C-2 (LCTY) - Body groundAlways11 to 14V
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
REPLACE MAIN BODY ECU
10.INSPECT DOOR COURTESY LIGHT (REAR DOOR RH)
Lighting System - Door Courtesy Light Circuit. LIGHTING EXT. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Remove the door courtesy light connector.

Check that the door courtesy light comes on.

  • OK:
  • Measurement ConditionSpecified Condition
    Battery positive (+) - Terminal 2
    Battery positive (-) - Terminal 1    		Light illumination
NG
Go to step 11
OK
END
11.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BODY GROUND)
Lighting System - Door Courtesy Light Circuit. LIGHTING EXT. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Remove the main body ECU.

except Double Swing Out Type:


Measure the voltage according to the value(s) in the table below.

  • Standard Voltage:
  • Tester ConnectionConditionSpecified Condition
    E2-7 (RCTY) - Body groundAlways11 to 14V

for Double Swing Out Type:


Measure the voltage according to the value(s) in the table below.

  • Standard Voltage:
  • Tester ConnectionConditionSpecified Condition
    E1-17 (RCTY) - Body groundAlways11 to 14V
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
REPLACE MAIN BODY ECU