Land Cruiser URJ200 URJ202 GRJ200 VDJ200 - MIRROR EXT
OUTER REAR VIEW MIRROR - INSPECTION
| 1. INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH (w/o Retract Mirror) |
Apply battery voltage and check the operation of the mirror.
- OK:
Measurement Condition Specified Condition Battery positive (+) → Terminal 3 (MV)
Battery negative (-) → Terminal 1 (M+)Turns upward (A) Battery positive (+) → Terminal 1 (M+)
Battery negative (-) → Terminal 3 (MV)Turns downward (B) Battery positive (+) → Terminal 2 (MH)
Battery negative (-) → Terminal 1 (M+)Turns left (C) Battery positive (+) → Terminal 1 (M+)
Battery negative (-) → Terminal 2 (MH)Turns right (D)
If the result is not as specified, replace the outer rear view mirror assembly LH.
| *a | Component without harness connected (Outer Rear View Mirror Assembly LH) |
w/ Side Turn Signal Light:
Check the side turn light assembly.
Apply battery voltage to the terminals of the connector, and check the illumination condition.
- OK:
Measurement Connection Specified Condition Battery positive (+) → Terminal 4 (TRNL)
Negative (-) end of the battery → Terminal 5 (GND)Side turn light illuminates
If the result is not as specified, check the side turn signal light assembly LH ().
| *a | Component without harness connected (Outer Rear View Mirror Assembly LH) |
| 2. INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH (w/o Retract Mirror) |
Apply battery voltage and check the operation of the mirror.
- OK:
Measurement Condition Specified Condition Battery positive (+) → Terminal 3 (MV)
Battery negative (-) → Terminal 1 (M+)Turns upward (A) Battery positive (+) → Terminal 1 (M+)
Battery negative (-) → Terminal 3 (MV)Turns downward (B) Battery positive (+) → Terminal 2 (MH)
Battery negative (-) → Terminal 1 (M+)Turns right (C) Battery positive (+) → Terminal 1 (M+)
Battery negative (-) → Terminal 2 (MH)Turns left (D)
If the result is not as specified, replace the outer rear view mirror assembly RH.
| *a | Component without harness connected (Outer Rear View Mirror Assembly RH) |
/ Side Turn Signal Light:
Check the side turn light assembly.
Apply battery voltage to the terminals of the connector, and check the illumination condition.
- OK:
Measurement Connection Specified Condition Battery positive (+) → Terminal 4 (TRNR)
Negative (-) end of the battery → Terminal 5 (GND)Side turn light illuminates
If the result is not as specified, check the side turn signal light assembly RH ().
| *a | Component without harness connected (Outer Rear View Mirror Assembly RH) |
| 3. INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH (w/ Retract Mirror) |
For each position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror movement.
- OK:
Measurement Condition Mirror Position Specified Condition Battery positive (+) → Terminal 19 (MR)
Battery negative (-) → Terminal 20 (MF)Forward position A Moves from A to retracted position E Battery negative (-) → Terminal 19 (MR)
Battery positive (+) → Terminal 20 (MF)Forward position A Does not move Battery positive (+) → Terminal 19 (MR)
Battery negative (-) → Terminal 20 (MF)Position between forward position A and driving position C Moves from B to retracted position E Battery negative (-) → Terminal 19 (MR)
Battery positive (+) → Terminal 20 (MF)Position between forward position A and driving position C Moves from B to forward position A Battery positive (+) → Terminal 19 (MR)
Battery negative (-) → Terminal 20 (MF)Driving position C Moves from C to retracted position E Battery negative (-) → Terminal 19 (MR)
Battery positive (+) → Terminal 20 (MF)Driving position C Does not move Battery positive (+) → Terminal 19 (MR)
Battery negative (-) → Terminal 20 (MF)Position between driving position C and retracted position E Moves from D to retracted position E Battery negative (-) → Terminal 19 (MR)
Battery positive (+) → Terminal 20 (MF)Position between driving position C and retracted position E Moves from D to driving position C Battery positive (+) → Terminal 19 (MR)
Battery negative (-) → Terminal 20 (MF)Retracted position E Does not move Battery negative (-) → Terminal 19 (MR)
Battery positive (+) → Terminal 20 (MF)Retracted position E Moves from E to driving position C
- NOTICE:
If the result is not as specified, replace the outer rear view mirror assembly LH.
| *a | Component without harness connected (Outer Rear View Mirror Assembly LH) |
Apply battery voltage and check the operation of the mirror.
- OK:
Measurement Condition Specified Condition Battery positive (+) → Terminal 7 (MV)
Battery negative (-) → Terminal 8 (M+)Turns upward Battery negative (-) → Terminal 8 (M+)
Battery positive (+) → Terminal 7 (MV)Turns downward Battery positive (+) → Terminal 9 (MH)
Battery negative (-) → Terminal 8 (M+)Turns left Battery negative (-) → Terminal 8 (M+)
Battery positive (+) → Terminal 9 (MH)Turns right
If the result is not as specified, replace the outer rear view mirror assembly LH.
| *a | Component without harness connected (Outer Rear View Mirror Assembly LH) |
w/ Mirror Heater:
Check the mirror heater.
Measure the resistance according to the value (s) in the table below.
- Standard Resistance:
Tester Connection Condition Specified Condition Terminal 6 (+) - Terminal 17 (-) 25°C (75°F) 3.0 to 3.9 Ω
If the result is not as specified, replace the outer rear view mirror assembly LH.
Apply battery voltage and check the operation of the mirror heater.
- OK:
Measurement Condition Specified Condition Battery positive (+) → Terminal 6 (+)
Battery negative (-) → Terminal 17 (-)Mirror becomes warm
- HINT:
- It will take a short time for the mirror to become warm.
If the result is not as specified, replace the outer rear view mirror assembly LH.
| *a | Component without harness connected (Outer Rear View Mirror Assembly LH) |
Check the side turn light assembly.
Apply battery voltage to the terminals of the connector, and check the illumination condition.
- OK:
Measurement Connection Specified Condition Battery positive (+) → Terminal 4 (TRNL)
Negative (-) end of the battery → Terminal 15 (GND)Side turn light illuminates
If the result is not as specified, check the side turn signal light assembly LH ().
| *a | Component without harness connected (Outer Rear View Mirror Assembly LH) |
w/EC Mirror:
Check the EC mirror operation.
Connect 1.5 V dry-cell battery.
Apply dry battery voltage and check operation of the mirror face, as shown in the table and illustration.
- OK:
Measurement Condition Specified Condition Battery positive (+) → Terminal 5 (EC+)
Battery negative (-) → Terminal 16 (EC-)Mirror surface becomes dark
If the result is not as specified, replace the outer rear view mirror assembly LH.
| *a | Component without harness connected (Outer Rear View Mirror Assembly LH) |
| 4. INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH (w/ Retract Mirror) |
For each position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror movement.
- OK:
Measurement Condition Mirror Position Specified Condition Battery positive (+) → Terminal 19 (MR)
Battery negative (-) → Terminal 20 (MF)Forward position A Moves from A to retracted position E Battery negative (-) → Terminal 19 (MR)
Battery positive (+) → Terminal 20 (MF)Forward position A Does not move Battery positive (+) → Terminal 19 (MR)
Battery negative (-) → Terminal 20 (MF)Position between forward position A and driving position C Moves from B to retracted position E Battery negative (-) → Terminal 19 (MR)
Battery positive (+) → Terminal 20 (MF)Position between forward position A and driving position C Moves from B to forward position A Battery positive (+) → Terminal 19 (MR)
Battery negative (-) → Terminal 20 (MF)Driving position C Moves from C to retracted position E Battery negative (-) → Terminal 19 (MR)
Battery positive (+) → Terminal 20 (MF)Driving position C Does not move Battery positive (+) → Terminal 19 (MR)
Battery negative (-) → Terminal 20 (MF)Position between driving position C and retracted position E Moves from D to retracted position E Battery negative (-) → Terminal 19 (MR)
Battery positive (+) → Terminal 20 (MF)Position between driving position C and retracted position E Moves from D to driving position C Battery positive (+) → Terminal 19 (MR)
Battery negative (-) → Terminal 20 (MF)Retracted position E Does not move Battery negative (-) → Terminal 19 (MR)
Battery positive (+) → Terminal 20 (MF)Retracted position E Moves from E to driving position C
- NOTICE:
If the result is not as specified, replace the outer rear view mirror assembly RH.
| *a | Component without harness connected (Outer Rear View Mirror Assembly RH) |
Apply battery voltage and check the operation of the mirror.
- OK:
Measurement Condition Specified Condition Battery positive (+) → Terminal 7 (MV)
Battery negative (-) → Terminal 8 (M+)Turns upward Battery negative (-) → Terminal 8 (M+)
Battery positive (+) → Terminal 7 (MV)Turns downward Battery positive (+) → Terminal 9 (MH)
Battery negative (-) → Terminal 8 (M+)Turns left Battery negative (-) → Terminal 8 (M+)
Battery positive (+) → Terminal 9 (MH)Turns right
If the result is not as specified, replace the outer rear view mirror assembly RH.
| *a | Component without harness connected (Outer Rear View Mirror Assembly RH) |
w/ Mirror Heater:
Check the mirror heater.
Measure the resistance according to the value (s) in the table below.
- Standard Resistance:
Tester Connection Condition Specified Condition Terminal 6 (+) - Terminal 17 (-) 25°C (75°F) 3.0 to 3.9 Ω
If the result is not as specified, replace the outer rear view mirror assembly RH.
Apply battery voltage and check the operation of the mirror heater.
- OK:
Measurement Condition Specified Condition Battery positive (+) → Terminal 6 (+)
Battery negative (-) → Terminal 17 (-)Mirror becomes warm
- HINT:
- It will take a short time for the mirror to become warm.
If the result is not as specified, replace the outer rear view mirror assembly.
| *a | Component without harness connected (Outer Rear View Mirror Assembly RH) |
Check the side turn light assembly.
Apply battery voltage to the terminals of the connector, and check the illumination condition.
- OK:
Measurement Connection Specified Condition Battery positive (+) → Terminal 4 (TRNR)
Negative (-) end of the battery → Terminal 15 (GND)Side turn light illuminates
If the result is not as specified, check the side turn signal light assembly RH ().
| *a | Component without harness connected (Outer Rear View Mirror Assembly RH) |
w/EC Mirror:
Check the EC mirror operation.
Connect 1.5 V dry-cell battery.
Apply dry battery voltage and check operation of the mirror face, as shown in the table and illustration.
- OK:
Measurement Condition Specified Condition Battery positive (+) → Terminal 5 (EC+)
Battery negative (-) → Terminal 16 (EC-)Mirror surface becomes dark
If the result is not as specified, replace the outer rear view mirror assembly RH.
| *a | Component without harness connected (Outer Rear View Mirror Assembly RH) |