Land Cruiser URJ200 URJ202 GRJ200 VDJ200 - DOOR / HATCH
BACK DOOR - INSPECTION
| 1. INSPECT BACK DOOR REMOTE CONTROL ASSEMBLY |
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection Switch Condition Specified Condition 1 - 2 Back door remote control is pulled (on) Below 1 Ω 1 - 2 Back door remote control is not pulled (off) 10 kΩ or higher
If the result is not as specified, replace the back door remote control assembly.
| *a | Component without harness connected (Back Door Remote Control Assembly) |
| *b | Not pulled (off) |
| *c | Pulled (on) |
| 2. INSPECT LOWER TAIL GATE LOCK ASSEMBLY LH |
Operation check:
Set the lower tail gate lock LH to the full-latch position.
Apply battery voltage and check operation of the lower tail gate lock motor LH.
- OK:
Measurement Condition Specified Condition Battery positive (+) → Terminal 6 (ACT-)
Battery negative (-) → Terminal 5 (ACT+)Latch turns to open-latch position
If the result is not as specified, replace the lower tail gate lock assembly LH.
Set the lower tail gate lock LH to the half-latch position.
Apply battery voltage and check operation of the lower tail gate lock motor LH.
- OK:
Measurement Condition Specified Condition Battery positive (+) → Terminal 5 (ACT+)
Battery negative (-) → Terminal 6 (ACT-)Latch turns to over-latch position
If the result is not as specified, replace the lower tail gate lock assembly LH.
| *a | Component without harness connected (Lower Tail Gate Lock Assembly LH) |
| *b | Over-latch |
| *c | Full-latch |
| *d | Half-latch |
| *e | Open-latch |
Resistance check:
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Close Position Switch Tester Connection Condition Specified Condition 7 (HND) - 8 (GND) Over-latch Below 1 Ω 7 (HND) - 8 (GND) Full-latch 10 kΩ or higher 7 (HND) - 8 (GND) Half-latch 10 kΩ or higher 7 (HND) - 8 (GND) Open-latch 10 kΩ or higher
If the result is not as specified, replace the lower tail gate lock assembly LH.
- Lower Tail Gate Courtesy Switch:
Tester Connection Condition Specified Condition 2 (FUL) - 3 (E1) Over-latch 10 kΩ or higher 2 (FUL) - 3 (E1) Full-latch 10 kΩ or higher 2 (FUL) - 3 (E1) Half-latch Below 1 Ω 2 (FUL) - 3 (E1) Open-latch Below 1 Ω
If the result is not as specified, replace the lower tail gate lock assembly LH.
- Half-latch Switch:
Tester Connection Condition Specified Condition 1 (HAF) - 3 (E1) Over-latch 10 kΩ or higher 1 (HAF) - 3 (E1) Full-latch Below 1 Ω 1 (HAF) - 3 (E1) Half-latch 10 kΩ or higher 1 (HAF) - 3 (E1) Open-latch Below 1 Ω
If the result is not as specified, replace the lower tail gate lock assembly LH.
- Pawl Switch:
Tester Connection Condition Specified Condition 4 (POL) - 3 (E1) Over-latch 10 kΩ or higher 4 (POL) - 3 (E1) Full-latch Below 1 Ω 4 (POL) - 3 (E1) Half-latch Below 1 Ω 4 (POL) - 3 (E1) Open-latch 10 kΩ or higher
If the result is not as specified, replace the lower tail gate lock assembly LH.
| *a | Component without harness connected (Lower Tail Gate Lock Assembly LH) |
| *b | Over-latch |
| *c | Full-latch |
| *d | Half-latch |
| *e | Open-latch |
| 3. INSPECT LOWER TAIL GATE LOCK ASSEMBLY RH |
Operation check:
Set the lower tail gate lock RH to the full-latch position.
Apply battery voltage and check operation of the lower tail gate lock motor RH.
- OK:
Measurement Condition Specified Condition Battery positive (+) → Terminal 6 (ACT-)
Battery negative (-) → Terminal 5 (ACT+)Latch turns to open-latch position
If the result is not as specified, replace the lower tail gate lock assembly RH.
Set the lower tail gate lock RH to the half-latch position.
Apply battery voltage and check operation of the lower tail gate lock motor RH.
- OK:
Measurement Condition Specified Condition Battery positive (+) → Terminal 5 (ACT+)
Battery negative (-) → Terminal 6 (ACT-)Latch turns to over-latch position
If the result is not as specified, replace the lower tail gate lock assembly RH.
| *a | Component without harness connected (Lower Tail Gate Lock Assembly RH) |
| *b | Over-latch |
| *c | Full-latch |
| *d | Half-latch |
| *e | Open-latch |
Resistance check:
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Close Position Switch Tester Connection Condition Specified Condition 7 (HND) - 8 (GND) Over-latch Below 1 Ω 7 (HND) - 8 (GND) Full-latch 10 kΩ or higher 7 (HND) - 8 (GND) Half-latch 10 kΩ or higher 7 (HND) - 8 (GND) Open-latch 10 kΩ or higher
If the result is not as specified, replace the lower tail gate lock assembly RH.
- Lower Tail Gate Courtesy Switch:
Tester Connection Condition Specified Condition 2 (FUL) - 3 (E1) Over-latch 10 kΩ or higher 2 (FUL) - 3 (E1) Full-latch 10 kΩ or higher 2 (FUL) - 3 (E1) Half-latch Below 1 Ω 2 (FUL) - 3 (E1) Open-latch Below 1 Ω
If the result is not as specified, replace the lower tail gate lock assembly RH.
- Half-latch Switch:
Tester Connection Condition Specified Condition 1 (HAF) - 3 (E1) Over-latch 10 kΩ or higher 1 (HAF) - 3 (E1) Full-latch Below 1 Ω 1 (HAF) - 3 (E1) Half-latch 10 kΩ or higher 1 (HAF) - 3 (E1) Open-latch Below 1 Ω
If the result is not as specified, replace the lower tail gate lock assembly RH.
- Pawl Switch:
Tester Connection Condition Specified Condition 4 (POL) - 3 (E1) Over-latch 10 kΩ or higher 4 (POL) - 3 (E1) Full-latch Below 1 Ω 4 (POL) - 3 (E1) Half-latch Below 1 Ω 4 (POL) - 3 (E1) Open-latch 10 kΩ or higher
If the result is not as specified, replace the lower tail gate lock assembly RH.
| *a | Component without harness connected (Lower Tail Gate Lock Assembly RH) |
| *b | Over-latch |
| *c | Full-latch |
| *d | Half-latch |
| *e | Open-latch |