Vehicle Stability Control System Brake Warning Light Remains On

Brake. Land Cruiser. Urj200, 202 Grj200 Vdj200
Brake Control Dynamic Control Systems. Land Cruiser. Urj200, 202 Grj200 Vdj200

DESCRIPTION

WIRING DIAGRAM

INSPECTION PROCEDURE

CHECK DTC

INSPECT IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED

INSPECT BATTERY

CHECK CAN COMMUNICATION LINE

CHECK DTC (CAN COMMUNICATION SYSTEM)

CHECK HARNESS AND CONNECTOR (IG1 TERMINAL)

CHECK HARNESS AND CONNECTOR (GND1, GND2 AND GND3 TERMINAL)

PERFORM ACTIVE TEST USING GTS (BRAKE WARNING LIGHT)

VEHICLE STABILITY CONTROL SYSTEM - Brake Warning Light Remains ON


DESCRIPTION

The brake warning light comes on when brake fluid is insufficient, the parking brake is applied or the EBD is defective.

WIRING DIAGRAM


Land Cruiser. Urj200, 202 Grj200 Vdj200.Brake Control Dynamic Control Systems.Anti-Lock Brake System.Vehicle Stability Control System Brake Warning Light Remains On


INSPECTION PROCEDURE

NOTICE:
After replacing the master cylinder solenoid, perform zero point calibration and store the system information (Click here).
1.CHECK DTC

  1. Check for DTCs (Click here).

    Result
    Result
    		Proceed to
    DTC is not output
    		A
    DTC is output
    		B


B
REPAIR CIRCUIT INDICATED BY OUTPUT DTC (Click here)
A


2.INSPECT IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED

  1. Check the skid control ECU (master cylinder solenoid) connector connection.

    OK:
    The connector is securely connected.


NG
CONNECT CONNECTOR TO ECU CORRECTLY
OK


3.INSPECT BATTERY

  1. Check the battery voltage.

    Standard voltage:
    11 to 14 V

    Result
    Result
    		Proceed to
    OK
    		A
    NG (for 1GR-FE)
    		B
    NG (for 1VD-FTV)
    		C
    NG (for 1UR-FE)
    		D
    NG (for 3UR-FE)
    		E


B
GO TO CHARGING SYSTEM (ON-VEHICLE INSPECTION) (Click here)

C
GO TO CHARGING SYSTEM (ON-VEHICLE INSPECTION) (Click here)

D
GO TO CHARGING SYSTEM (ON-VEHICLE INSPECTION) (Click here)

E
GO TO CHARGING SYSTEM (ON-VEHICLE INSPECTION) (Click here)
A


4.CHECK CAN COMMUNICATION LINE

  1. Turn the ignition switch off.

  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON and the GTS on.

  1. Select "CAN Bus Check" from the System Selection Menu screen, and follow the prompts on the screen to inspect the CAN Bus.

    OK:
    "CAN Bus Check" indicates no malfunctions in CAN communication.

    Result
    Result
    		Proceed to
    OK
    		A
    NG (for LHD (with Central Gateway ECU))
    		B
    NG (for LHD (without Central Gateway ECU))
    		C
    NG (for RHD (with Central Gateway ECU))
    		D
    NG (for RHD (without Central Gateway ECU))
    		E


B
GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)

C
GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)

D
GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)

E
GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)
A


5.CHECK DTC (CAN COMMUNICATION SYSTEM)

  1. Turn the ignition switch off.

  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON and the GTS on.

  1. for LHD (with Central Gateway ECU):
    Check for DTCs (Click here).

  1. for LHD (without Central Gateway ECU):
    Check for DTCs (Click here).

  1. for RHD (with Central Gateway ECU):
    Check for DTCs (Click here).

  1. for RHD (without Central Gateway ECU):
    Check for DTCs (Click here).

    Result
    Result
    		Proceed to
    CAN DTC is not output
    		A
    CAN DTC is output (for LHD (with Central Gateway ECU))
    		B
    CAN DTC is output (for LHD (without Central Gateway ECU))
    		C
    CAN DTC is output (for RHD (with Central Gateway ECU))
    		D
    CAN DTC is output (for RHD (without Central Gateway ECU))
    		E


B
GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)

C
GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)

D
GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)

E
GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)
A


6.CHECK HARNESS AND CONNECTOR (IG1 TERMINAL)

  1. Disconnect the skid control ECU (master cylinder solenoid) connector.



    Land Cruiser. Urj200, 202 Grj200 Vdj200.Brake Control Dynamic Control Systems.Anti-Lock Brake System.Vehicle Stability Control System Brake Warning Light Remains On

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    		Switch Condition
    		Specified Condition
    A24-46 (IG1) - Body ground
    		Ignition switch ON
    		11 to 14 V
    Text in Illustration
    *a
    		Front view of wire harness connector
    (to Skid Control ECU (Master Cylinder Solenoid))


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.CHECK HARNESS AND CONNECTOR (GND1, GND2 AND GND3 TERMINAL)
Land Cruiser. Urj200, 202 Grj200 Vdj200.Brake Control Dynamic Control Systems.Anti-Lock Brake System.Vehicle Stability Control System Brake Warning Light Remains On

  1. Turn the ignition switch off.

  1. Disconnect the skid control ECU (master cylinder solenoid) connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    		Condition
    		Specified Condition
    A24-1 (GND1) - Body ground
    		Always
    		Below 1 Ω
    A24-32 (GND2) - Body ground
    		Always
    		Below 1 Ω
    A25-4 (GND3) - Body ground
    		Always
    		Below 1 Ω
    Text in Illustration
    *a
    		Front view of wire harness connector
    (to Skid Control ECU [Master Cylinder Solenoid])


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8.PERFORM ACTIVE TEST USING GTS (BRAKE WARNING LIGHT)

  1. Turn the ignition switch off.

  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch ON.

  1. Turn the GTS on.

  1. Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.

    ABS/VSC/TRC
    Tester Display
    		Test Part
    		Control Range
    		Diagnostic Note
    Brake Warning Light
    		Brake warning light
    		Warning light ON/OFF
    		Observe the combination meter assembly.

  1. When performing the Brake Warning Light Active Test, check Brake Warning Light in the Data List.

    ABS/VSC/TRC
    Tester Display
    		Measurement Item/Range
    		Normal Condition
    		Diagnostic Note
    Brake Warning Light
    		Brake warning light/ ON or OFF
    		ON: Warning light on
    OFF: Warning light off
    		-

    Result
    Result
    		Proceed to
    Data List Display
    		Data List Display when Performing Active Test ON/OFF Operation
    ON
    		Changes between ON and OFF
    		A
    Does not change between ON and OFF (for LHD)
    		B
    Does not change between ON and OFF (for RHD)
    		C
    OFF
    		Changes between ON and OFF
    		A
    Does not change between ON and OFF (for LHD)
    		B
    Does not change between ON and OFF (for RHD)
    		C


B
REPLACE MASTER CYLINDER SOLENOID (Click here)

C
REPLACE MASTER CYLINDER SOLENOID (Click here)
A

REPLACE MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)