Dtc P1607 Cruise Control Input Processor

Engine Hybrid System. Yaris. Ncp93, 131
1Nz-Fe Engine Control. Yaris. Ncp93, 131

DESCRIPTION

MONITOR STRATEGY

TYPICAL ENABLING CONDITIONS

TYPICAL MALFUNCTION THRESHOLDS

CONFIRMATION DRIVING PATTERN

INSPECTION PROCEDURE

CHECK FOR DTC

DTC P1607 Cruise Control Input Processor


DESCRIPTION

The ECM continuously monitors its main and sub CPUs. This self-check ensures that the ECM is functioning properly. If outputs from the CPUs are different and deviate from the standard, the ECM will illuminate the MIL and store a DTC immediately.

DTC No.
DTC Detection Condition
Trouble Area
P1607
ECM CPUs malfunction
(1 trip detection logic)
ECM

MONITOR STRATEGY


Related DTC
P1607: Internal control module range check
Required sensors/Components (Main)
ECM
Required sensors/Components (Related)
Cruise control
Frequency of Operation
Continuous
Duration
0.3 seconds
MIL Operation
Immediate
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs not present
None
DMA communication error
Not detected

TYPICAL MALFUNCTION THRESHOLDS


Cruise control
Prohibited
When either condition below is met:
-
  1. Cruise control
Operating
  1. Low speed control
Operating

CONFIRMATION DRIVING PATTERN

NOTICE:
After turning ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (YARIS_NCP93 RM00000482L007X.html).
  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
  4. Turn the Techstream off.
  5. Turn the ignition switch off.
  6. Disconnect the Techstream.
  7. Disconnect the cable from the negative (-) battery terminal and wait for 1 minute.
  8. Connect the cable to the negative (-) battery terminal.
  9. Connect the Techstream to the DLC3.
  10. Turn the ignition switch to ON and turn the Techstream on.
  11. Wait for 16 seconds or more.
  12. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
  13. Read pending DTCs.
    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.
  14. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  15. Input the DTC: P1607.
  16. Check the DTC judgment result.

    Techstream Display
    		Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit
    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
  17. If the test result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (YARIS_NCP93 RM000000PDK0T5X.html).
    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.

INSPECTION PROCEDURE

NOTICE:
After turning ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (YARIS_NCP93 RM00000482L007X.html).
HINT:
Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
1.CHECK FOR DTC

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear the DTC (YARIS_NCP93 RM000000PDK0T5X.html).

  1. Turn the ignition switch off and turn the Techstream off.

  1. Disconnect the Techstream.

  1. Disconnect the cable from the negative (-) battery terminal and wait for 1 minute.

  1. Connect the cable to the negative (-) battery terminal.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Wait 16 seconds or more.

  1. Enter the following menus: Powertrain / Engine and ECT/ Trouble Codes.

  1. Read DTCs.

    OK:
    P1607 is not present.


NG
REPLACE ECM (YARIS_NCP93 RM000001CN002IX.html)
OK

CHECK FOR INTERMITTENT PROBLEMS (YARIS_NCP93 RM000000PDQ0Q2X.html)