Parking Brake Pedal Installation

Install the parking brake pedal assembly with the bolt and 2 nuts.

Torque:

39 N*m{398 kgf*cm, 29 ft.*lbf}

Connect the parking brake switch connector.

Install the No. 1 parking brake cable assembly to the body with the bolt, the nut, and a new No. 1 parking brake cable clamp.

Torque:

Bolt:

15 N*m{153 kgf*cm, 11 ft.*lbf}

Nut:

5.4 N*m{55 kgf*cm, 48 in.*lbf}

Using a brass bar and a hammer, install the clip to the No. 1 parking brake cable assembly.

Install the parking brake pedal assembly with the bolt and 2 nuts.

Torque:

15 N*m{153 kgf*cm, 11 ft.*lbf}

Connect the parking brake switch connector.

Install the No. 1 parking brake cable assembly to the body with the bolt.

Torque:

15 N*m{153 kgf*cm, 11 ft.*lbf}

Using a brass bar and a hammer, install the clip to the No. 1 parking brake cable sub-assembly.

Engage the 3 claws and install the No. 1 air duct sub-assembly.

Connect the No. 4 parking brake cable assembly to the No. 1 parking brake cable assembly.

Using SST and a wrench, hold the lock nut of the No. 1 parking brake cable and tighten the turnbuckle of the No. 4 parking brake cable assembly.

SST

09023-00101

Torque:

without SST:

5.4 N*m{55 kgf*cm, 48 in.*lbf}

with SST:

5.0 N*m{51 kgf*cm, 44 in.*lbf}

NOTICE:

1. Use a torque wrench with a fulcrum length of 250 mm (9.84 in.).
   
2. This torque is effective when SST is parallel to a torque wrench.
   

Check that the ignition switch is off.

Check that the battery negative (-) cable is disconnected.

CAUTION:

Wait for 90 seconds after disconnecting the cable to prevent airbag deployment.

Install the center airbag sensor assembly with the 3 bolts.

Torque:

17.5 N*m{179 kgf*cm, 13 ft.*lbf}

NOTICE:

1. If the center airbag sensor assembly has been dropped, or there are any cracks, dents or other defects in the case, bracket or connector, replace it with a new one.
   
2. When installing the center airbag sensor assembly, be careful that the SRS wiring does not interfere with other parts and that it is not pinched between other parts.
   

Check that there is no looseness in the installation parts of the center airbag sensor assembly.

Connect the holder (with connectors).

Check that the water-proof sheet is properly set.

Install the floor shift lever assembly with the 4 bolts.

Torque:

12 N*m{122 kgf*cm, 8.9 ft.*lbf}

Install the yaw rate and acceleration sensor with the 2 bolts.

NOTICE:

1. Do not damage the yaw rate and acceleration sensor.
   
2. Make sure that the yaw rate and acceleration sensor is installed securely.
   

Torque:

13 N*m{133 kgf*cm, 10 ft.*lbf}

Connect the yaw rate and acceleration sensor connector.

Install the No. 1 console box duct with the clip.

Engage the clip.

Install the No. 2 console box insert front with the 3 screws <F>.

Engage the clip.

Install the No. 1 console box insert front with the 3 screws <F>.

Install the 2 screws <F>.

Install the console box assembly with the 2 bolts <G>.

Install the console box carpet.

Install the console box pocket.

Connect each connector.

Engage the 4 claws.

Install the upper console panel sub-assembly with the 2 screws <F>.

Connect the connector.

Engage the 3 claws and 5 clips to install the upper console rear panel sub-assembly.

with Seat Heater System:

1. Connect each connector.
   

Engage the 6 claws and the 3 clips to install the floor shift position indicator housing sub-assembly.

Engage the 2 clips and install the No. 1 instrument cluster finish panel garnish.

Engage the 2 clips and install the No. 2 instrument cluster finish panel garnish.

Install the shift lever knob sub-assembly.

Engage the 3 claws and 3 clips.

Install the 4 screws <B>.

Install the lower instrument panel sub-assembly with the bolt <A>.

Engage the 4 claws and 2 guides and install the instrument panel No. 2 under cover.

Connect each connector.

Install the combination meter assembly with the 4 screws <E>.

Engage the guide and the 4 claws.

Install the instrument cluster finish panel with the 2 clips.

Connect each connector.

Engage the 3 claws and 2 clips to install the No. 1 instrument panel sub-assembly.

Install the air hose and connect the connector.

Engage the 2 claws and the DLC3.

Engage the claw and the 4 clips.

Instal the lower instrument panel finish panel LH with the screw <B> and bolt <A>.

Engage the 2 clips.

Install the cowl side trim sub-assembly LH with the cowl side trim clip.

Engage the 7 claws and 3 clips, then install the front door scuff plate LH.