Brake. Camry. Acv40 Gsv40
Brake Control. Camry. Acv40 Gsv40
Vehicle Stability Control System -- Diagnostic Trouble Code Chart |
- If a trouble code is displayed during the DTC check, check the circuit indicated by the DTC. For details of each code, refer to the page for the respective "DTC Code" in the DTC chart.
- Inspect the fuse and relay before investigating the trouble areas as shown in the table below.
| DTC Code | Detection Item | Trouble Area | See page |
| C0200/31(*1) | Front Speed Sensor RH Circuit | 1. Front speed sensor RH 2. Speed sensor circuit 3. Speed sensor rotor 4. Sensor installation 5. Brake actuator assembly (Skid control ECU) | CAMRY_ACV40 RM000000XI906RX.html |
| C0205/32(*1) | Front Speed Sensor LH Circuit | 1. Front speed sensor LH 2. Speed sensor circuit 3. Speed sensor rotor 4. Sensor installation 5. Brake actuator assembly (Skid control ECU) | CAMRY_ACV40 RM000000XI906RX.html |
| C0210/33(*1) | Rear Speed Sensor RH Circuit | 1. Rear speed sensor RH 2. Speed sensor circuit 3. Speed sensor rotor 4. Sensor installation 5. Brake actuator assembly (Skid control ECU) | CAMRY_ACV40 RM000000XIA05RX.html |
| C0215/34(*1) | Rear Speed Sensor LH Circuit | 1. Rear speed sensor LH 2. Speed sensor circuit 3. Speed sensor rotor 4. Sensor installation 5. Brake actuator assembly (Skid control ECU) | CAMRY_ACV40 RM000000XIA05RX.html |
| C0226/21 | SFR Solenoid Circuit | 1. Brake actuator assembly 2. SFRH or SFRR circuit | CAMRY_ACV40 RM000000XI804VX.html |
| C0236/22 | SFL Solenoid Circuit | 1. Brake actuator assembly 2. SFLH or SFLR circuit | CAMRY_ACV40 RM000000XI804VX.html |
| C0246/23 | SRR Solenoid Circuit | 1. Brake actuator assembly 2. SRRH or SRRR circuit | CAMRY_ACV40 RM000000XI804VX.html |
| C0256/24 | SRL Solenoid Circuit | 1. Brake actuator assembly 2. SRLH or SRLR circuit | CAMRY_ACV40 RM000000XI804VX.html |
| C0273/13(*1) | Open in ABS Motor Relay Circuit | 1. ABS NO. 1 fuse 2. VSC NO. 2 relay 3. VSC NO. 2 relay circuit 4. Brake actuator assembly | CAMRY_ACV40 RM000000XIB020X.html |
| C0274/14 | Short to B+ in ABS Motor Relay Circuit | 1. ABS NO. 1 fuse 2. VSC NO. 2 relay 3. VSC NO. 2 relay circuit 4. Brake actuator assembly | CAMRY_ACV40 RM000000XIB020X.html |
| C0278/11 | Open in ABS Solenoid Relay Circuit | 1. ABS NO. 2 fuse 2. ABS solenoid relay 3. ABS solenoid relay circuit 4. Brake actuator assembly | CAMRY_ACV40 RM000000XI7046X.html |
| C0279/12 | Short to B+ in ABS Solenoid Relay Circuit | Brake actuator assembly | CAMRY_ACV40 RM000000XI7046X.html |
| C1225/25 | SM Solenoid Circuit | 1. Brake actuator assembly 2. SM1 or SM2 circuit | CAMRY_ACV40 RM000000XI804VX.html |
| C1235/35 | Foreign Object is Attached on Tip of Front Speed Sensor RH | 1. Front speed sensor RH 2. Speed sensor rotor 3. Sensor installation 4. Brake actuator assembly (Skid control ECU) | CAMRY_ACV40 RM000000XIC04GX.html |
| C1236/36 | Foreign Object is Attached on Tip of Front Speed Sensor LH | 1. Front speed sensor LH 2. Speed sensor rotor 3. Sensor installation 4. Brake actuator assembly (Skid control ECU) | CAMRY_ACV40 RM000000XIC04GX.html |
| C1238/38 | Foreign Object is Attached on Tip of Rear Speed Sensor RH | 1. Rear speed sensor RH 2. Speed sensor rotor 3. Sensor installation 4. Brake actuator assembly (Skid control ECU) | CAMRY_ACV40 RM000000XIC04GX.html |
| C1239/39 | Foreign Object is Attached on Tip of Rear Speed Sensor LH | 1. Rear speed sensor LH 2. Speed sensor rotor 3. Sensor installation 4. Brake actuator assembly (Skid control ECU) | CAMRY_ACV40 RM000000XIC04GX.html |
| C1241/41 | Low Battery Positive Voltage | 1. ECU-IG NO. 2 fuse 2. Battery 3. Charging system 4. Power source circuit 5. Internal power supply circuit of the skid control ECU | CAMRY_ACV40 RM000000XW6051X.html |
| C1243/43(*1) | Acceleration Sensor Stuck Malfunction | 1. Yaw rate and acceleration sensor 2. Yaw rate and acceleration sensor circuit | CAMRY_ACV40 RM000001RFV03JX.html |
| C1244/44 | Open or Short in Acceleration Sensor Circuit | 1. Yaw rate and acceleration sensor 2. Yaw rate and acceleration sensor circuit | CAMRY_ACV40 RM000001RFV03JX.html |
| C1245/45(*1) | Acceleration Sensor Output Malfunction | 1. Yaw rate and acceleration sensor 2. Yaw rate and acceleration sensor circuit | CAMRY_ACV40 RM000001RFV03JX.html |
| C1246/46(*2) | Master Cylinder Pressure Sensor Malfunction | 1. Master cylinder pressure sensor 2. Master cylinder pressure sensor circuit 3. Stop light switch circuit 4. Brake actuator assembly | CAMRY_ACV40 RM000000XIG04WX.html |
| C1249/49 | Open in Stop Light Switch Circuit | 1. STOP fuse 2. Stop light switch 3. Stop light switch circuit 4. Brake actuator assembly (Skid control ECU) | CAMRY_ACV40 RM000000XIE05UX.html |
| C1251/51(*1) | Open in Pump Motor Circuit | 1. Brake actuator assembly (GND circuit) 2. Brake actuator assembly (Motor circuit) | CAMRY_ACV40 RM000000XIF04DX.html |
| C1361/91 | Short Circuit in ABS Motor Fail Safe Relay Circuit | 1. ABS NO. 1 fuse 2. VSC NO. 1 (fail safe) relay 3. VSC NO. 1 (fail safe) relay circuit 4. Brake actuator assembly | CAMRY_ACV40 RM000000XIB020X.html |
| C1381/97 | Acceleration Sensor Power Supply Voltage Malfunction | 1. Yaw rate and acceleration sensor 2. Yaw rate and acceleration sensor power source circuit | CAMRY_ACV40 RM000001RFV03JX.html |
| C1442/44 | Invalid Data Received from Acceleration Sensor | Yaw rate and acceleration sensor | CAMRY_ACV40 RM000003NL3017X.html |
| U0073/94 | Control Module Communication Bus OFF | CAN communication system | CAMRY_ACV40 RM000000YUO053X.html |
| U0124/95 | Lost Communication with Lateral Acceleration Sensor Module | CAN communication system (Skid control ECU to yaw rate and acceleration sensor) | CAMRY_ACV40 RM000000YUO053X.html |
Even after the trouble areas are repaired, the ABS warning light will not go off unless the following operations are performed:
- (*1):
- Drive the vehicle at 12 mph (20 km/h) for 30 seconds or more and check that the ABS warning light goes off.
- Clear the DTC.
- (*2):
- Keep the vehicle stationary for 5 seconds or more and depress the brake pedal lightly 2 or 3 times.
- Drive the vehicle at the vehicle speed of 31 mph (50 km/h) and keep depressing the brake pedal strongly for approximately 3 seconds.
- Repeat the above operation 3 times or more and check that the ABS warning light goes off.
- Clear the DTC.
- HINT:
- In some cases, the intelligent tester cannot be used when the ABS warning light remains on.
| DTC Code | Detection Item | Trouble Area | See page |
| 43 | ABS Control System Malfunction | ABS control system | CAMRY_ACV40 RM000002CSA00DX.html |
| C1201/51 | Engine Control System Malfunction | Engine control system | CAMRY_ACV40 RM000000XII03ZX.html |
| C1203/53 | ECM Communication Circuit Malfunction | ECM | CAMRY_ACV40 RM000000XIJ00BX.html |
| C1210/36 | Zero Point Calibration of Yaw Rate Sensor Undone | 1. Brake actuator assembly (Skid control ECU) 2. Yaw rate and acceleration sensor 3. Zero point calibration undone | CAMRY_ACV40 RM000000XIK03IX.html |
| C1231/31 | Steering Angle Sensor Circuit Malfunction | 1. Steering angle sensor 2. Steering angle sensor circuit 3. Steering angle sensor power supply 4. Brake actuator assembly (Skid control ECU) | CAMRY_ACV40 RM000000XIM053X.html |
| C1232/32 | Stuck in Acceleration Sensor | 1. Yaw rate and acceleration sensor 2. Yaw rate and acceleration sensor circuit | CAMRY_ACV40 RM000001RFV03JX.html |
| C1234/34 | Yaw Rate Sensor Malfunction | 1. Yaw rate and acceleration sensor 2. Yaw rate and acceleration sensor circuit | CAMRY_ACV40 RM000001RFV03JX.html |
| C1290/66 | Steering Angle Sensor Zero Point Malfunction | 1. Yaw rate and acceleration sensor zero point calibration incomplete 2. Poor adjustment of the centered position of the steering wheel 3. Poor adjustment of front wheel alignment | CAMRY_ACV40 RM000000ZRR052X.html |
| C1336/39 | Zero Point Calibration of Acceleration Sensor Undone | 1. Brake actuator assembly (Skid control ECU) 2. Yaw rate and acceleration sensor 3. Zero point calibration undone | CAMRY_ACV40 RM000000XIK03IX.html |
| C1439/66 | Steering Angle Sensor Initialization Incomplete | 1. Steering angle sensor 2. Yaw rate and acceleration sensor 3. Brake actuator assembly (Skid control ECU) | CAMRY_ACV40 RM000003NJL01AX.html |
| C1440/98 | Unusual Bank Angle Detected | Yaw rate and acceleration sensor | CAMRY_ACV40 RM000003NL2011X.html |
| C1443/34 | Invalid Data Received from Yaw Rate Sensor | Yaw rate and acceleration sensor | CAMRY_ACV40 RM000003NL3017X.html |
| C1445/66 | Vehicle Driven with Steering Angle Sensor not Initialized | 1. Steering angle sensor 2. Yaw rate and acceleration sensor 3. Brake actuator assembly (Skid control ECU) | CAMRY_ACV40 RM000003NJL01AX.html |
| U0100/65 | Lost Communication with ECM / PCM | CAN communication system (Skid control ECU to ECM) | CAMRY_ACV40 RM000000YUO053X.html |
| U0123/62 | Lost Communication with Yaw Rate Sensor Module | CAN communication system (Skid control ECU to yaw rate and acceleration sensor) | CAMRY_ACV40 RM000000YUO053X.html |
| U0126/63 | Lost Communication with Steering Angle Sensor Module | CAN communication system (Skid control ECU to steering angle sensor) | CAMRY_ACV40 RM000000YUO053X.html |
- HINT:
- In some cases, the intelligent tester cannot be used when the SLIP indicator light remains on.
| DTC Code | Detection Item | Trouble Area | See page |
| C1271/71 | Low Output Signal of Front Speed Sensor RH (Test Mode DTC) | 1. Front speed sensor RH 2. Sensor installation 3. Speed sensor rotor | CAMRY_ACV40 RM000000XI906RX.html |
| C1272/72 | Low Output Signal of Front Speed Sensor LH (Test Mode DTC) | 1. Front speed sensor LH 2. Sensor installation 3. Speed sensor rotor | CAMRY_ACV40 RM000000XI906RX.html |
| C1273/73 | Low Output Signal of Rear Speed Sensor RH (Test Mode DTC) | 1. Rear speed sensor RH 2. Sensor installation 3. Speed sensor rotor | CAMRY_ACV40 RM000000XIA05RX.html |
| C1274/74 | Low Output Signal of Rear Speed Sensor LH (Test Mode DTC) | 1. Rear speed sensor LH 2. Sensor installation 3. Speed sensor rotor | CAMRY_ACV40 RM000000XIA05RX.html |
| C1275/75 | Abnormal Change in Output Signal of Front Speed Sensor RH (Test Mode DTC) | Speed sensor rotor | CAMRY_ACV40 RM000000XIC04GX.html |
| C1276/76 | Abnormal Change in Output Signal of Front Speed Sensor LH (Test Mode DTC) | Speed sensor rotor | CAMRY_ACV40 RM000000XIC04GX.html |
| C1277/77 | Abnormal Change in Output Signal of Rear Speed Sensor RH (Test Mode DTC) | Speed sensor rotor | CAMRY_ACV40 RM000000XIC04GX.html |
| C1278/78 | Abnormal Change in Output Signal of Rear Speed Sensor LH (Test Mode DTC) | Speed sensor rotor | CAMRY_ACV40 RM000000XIC04GX.html |
| C1279/79 | Acceleration Sensor Output Voltage Malfunction (Test Mode DTC) | 1. Yaw rate and acceleration sensor 2. Sensor installation | CAMRY_ACV40 RM000001RFV03JX.html |
| C1281/81 | Master Cylinder Pressure Sensor Output Malfunction (Test Mode DTC) | 1. Stop light switch 2. Master cylinder pressure sensor | CAMRY_ACV40 RM000000XIG04WX.html |
| DTC Code | Detection Item | Trouble Area | See page |
| C0371/71 | Yaw Rate Sensor (Test Mode DTC) | Yaw rate and acceleration sensor | CAMRY_ACV40 RM000001RFV03JX.html |