Can Communication System Main Body Ecu Communication Stop Mode

Communication System. Toyota Rav4. Aca30, 33, 38 Gsa33 Zsa30, 35
Can Communication. Toyota Rav4. Aca30, 33, 38 Gsa33 Zsa30, 35

DESCRIPTION

WIRING DIAGRAM

INSPECTION PROCEDURE

DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CHECK CAN BUS LINE FOR DISCONNECTION (MAIN BODY ECU BRANCH WIRE)

CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BATTERY AND BODY GROUND)

CAN COMMUNICATION SYSTEM - Main Body ECU Communication Stop Mode


DESCRIPTION


Detection Item
Symptom
Trouble Area
Main Body ECU Communication Stop Mode
Either condition is met:
  1. "Main Body" is not displayed on "Bus Check".
  2. "Main Body ECU Communication Stop Mode" in "DTC Combination Table" applies.
  1. Power source or inside main body ECU
  2. Main body ECU branch wire or connector
  3. Main body ECU

WIRING DIAGRAM


Toyota Rav4. Aca30, 33, 38 Gsa33 Zsa30, 35.Can Communication.Can Communication System.Can Communication System  Main Body Ecu Communication Stop Mode


INSPECTION PROCEDURE

NOTICE:
  1. Turn the ignition switch off before measuring the resistances of the main wire and the branch wire.
  2. For Auto:
    After the ignition switch is turned off, check that the key reminder warning system is not in operation.
  3. For Reminder:
    After the ignition switch is turned off, check that the key reminder warning system and light reminder buzzer are not in operation.
  4. Before measuring the resistance, leave the vehicle for at least 1 minute and do not operate the ignition switch, any switches or doors. If doors need to be opened in order to check connectors, open the doors and leave them open.
HINT:
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.
1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistance of the main wire and the branch wire.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
    NOTICE:
    1. w/ Navigation System (for HDD):
      After the ignition switch is turned off, the HDD navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) battery terminal.
    2. When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

next


2.CHECK CAN BUS LINE FOR DISCONNECTION (MAIN BODY ECU BRANCH WIRE)


    Toyota Rav4. Aca30, 33, 38 Gsa33 Zsa30, 35.Can Communication.Can Communication System.Can Communication System  Main Body Ecu Communication Stop Mode
  1. Disconnect the E20 main body ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E20-15 (CANH) - E20-16 (CANL)
    Ignition switch off
    54 to 69 Ω


NG
REPAIR OR REPLACE MAIN BODY ECU BRANCH WIRE OR CONNECTOR (CANH, CANL)
OK


3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BATTERY AND BODY GROUND)
  1. Connect the cable to the negative (-) battery terminal.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.


  1. Disconnect the E19, IB and IE main body ECU connectors.


    Toyota Rav4. Aca30, 33, 38 Gsa33 Zsa30, 35.Can Communication.Can Communication System.Can Communication System  Main Body Ecu Communication Stop Mode

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    IE-17 (GND1) - Body ground
    Always
    Below 1 Ω
    E19-4 (GND2) - Body ground
    Always
    Below 1 Ω
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    w/ Entry and Start System
    Tester Connection
    Condition
    Specified Condition
    E19-1 (AM1) - Body ground
    Always
    11 to 14 V
    w/o Entry and Start System
    Tester Connection
    Condition
    Specified Condition
    IB-30 (BECU) - Body ground
    Always
    11 to 14 V


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU